K09 卫生、安全、劳动保护 标准查询与下载

BS EN 61111:2009 带电作业.电气绝缘垫

This International Standard is applicable to electrical insulating matting made of elastomer for use as a floor covering for the electrical protection of workers on electrical installations.

Live working - Electrical insulating matting

DIN EN 61111:2010 带电作业.电绝缘垫(IEC 61111-2009).德文版本EN 61111-2009

This Standard is applicable to electrical insulating matting made of elastomer for use as a floor covering for the electrical protection of workers on a.c. installations.

Live working - Electrical insulating matting (IEC 61111:2009); German version EN 61111:2009

DB42/T 602-2010 防雷装置设计技术评价规范

Technical specifications for technical examination of design for lightning protection system

DIN EN 62192:2010 带电工作.绝缘绳索(IEC 62192-2009).德文版本EN 62192-2009

This standard covers insulating ropes that are utilized during live working procedures in contact with parts of installations operating at voltages up to and including 800 kV r.m.s.

Live working - Insulating ropes (IEC 62192:2009); German version EN 62192:2009

DIN EN 50468:2010 带通信端口的设备用由于闪电导致过电压和过电流的抵抗力要求

This European Standard specifies the minimum level of resistibility of equipment having telecommunicatons port(s) to overvoltages and overcurrents. This standard covers telecommunications equipment installed at customer premises. Overvoltages or overcurrents covered by this European Standard are surges due to direct or indirect lightning on the telecommunication line plant.

Resistibility requirements to overvoltages and overcurrents due to lightning for equipment having telecommunication ports; German version EN 50468:2009

ASTM D3032-10 单连线绝缘的标准试验方法

1.1 These test methods cover procedures for testing hookup wire. 1.2 For the purposes of these test methods, hookup wire insulation includes all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness or flat ribbon cable. The insulating materials include not only the primary insulation over the conductor, but also insulating jackets over shielded constructions. 1.3 The test procedures and their locations are as follows:

Standard Test Methods for Hookup Wire Insulation

ANSI/UL 61010-031-2010 测量,控制和实验室用电气设备安全性要求标准.第031部分:电气测量和试验用手持探头组件安全性要求

Proposed Requirements based on Amendment 1 of IEC 61010-031

Standard for Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test

NRS 040-4-2009 中压操作规范．第4部分：网络操作用供电行业培训、能力评估和授权用建议模型

Sets out the process, to designated persons, for skills development, competency declaration, assessment and authorization of electricity supply industry employees and other persons.

High-voltage operating regulations Part 4: Recommended model for the training, competency assessment and authorization of the Electricity Supply Industry for network operations

IEC 61243-3:2009 带电作业.电压检测器.第3部分:两极低压型

This part of IEC 61243 is applicable to hand-held two-pole voltage detectors with its accessories (crocodile clips and detachable leads) to be used in contact with parts of electrical systems: ?C for a.c. voltages not exceeding 1 000 V at nominal frequencies between 16 2 3 Hz and up to 500 Hz@ and/o ?C for d.c. voltages not exceeding 1 500 V. NOTE The a.c. voltages defined in this standard refer either to phase-to-phase voltages or phase to neutral voltages Contact electrode extensions are not covered by this standard. Voltage detectors covered by this standard are intended to be used under dry and humid conditions@ both indoor and outdoor. They are not intended to be used under rain conditions. Voltage detectors covered by this standard are not intended to be used for continuous operation. Voltage detectors covered by this standard are intended to be used up to 2 000 m above sea level. This standard also includes provisions for the following supplementary functions when available (see Annex B): ?C phase indication@ ?C rotating field indication@ and ?C continuity check. Other supplementary functions are not covered by this standard. Voltage detectors covered by this standard are not considered as measuring devices. Relevant safety requirements for measuring devices are included in IEC 61010 series.

Live working - Voltage detectors - Part 3: Two-pole low-voltage type

SS 551-2009 接地实施规程

1.1.1 General This Code gives guidance on the methods which may be adopted to earth an electrical system for th purpose of limiting the potential (with respect to the general mass of the earth) of current-carryin conductors forming part of the system, and non-current-carrying metalwork associated with equipmen apparatus, and appliances connected to the system. The former object is normally essential to the proper operation of the system, and this aspect is generall known as "system earthing". The latter concerns the safety of human life, of animals and of propert, and this aspect is sometimes known as "equipment earthing". The term "earthing" is used in this regard whether or not reliance is placed on the earth itself as a lov impedance return path for earth fault current. 1.1.2 Exclusion from scope This Code applies to land-based installations; it does not apply to trains, ships, aircraft or offshore installations, nor does it deal with the earthing of medical equipment or special problems encounterec with solid-state electronic components and equipment due to their sensitivity to static electricity. This standard does not address electromagnetic compatibility requirements for earthing, nor does it givE recommendation for functional earthing. 1.1.3 Materials, appliances and components Materials, appliances and components should comply with the relevant Singapore Standards, International Electrotechnical Commission Publications, British Standards or other equivalent national standards.

Code of practice for earthing

NF C92-131:2009 声频,视频和信息技术设备.生产过程中常规电气安全性试验

Audio, video and information technology equipment - Routine electrical safety testing in production.

BS EN 50468:2009 有通信站的设备耐受由放电火花引起的过电压和过电流的要求

This European Standard specifies the minimum level of resistibility of equipment having telecommunication port(s) to overvoltages and overcurrents. This European Standard covers telecommunication equipment installed at customer premises as shown in Figure 1. Overvoltages or overcurrents covered by this European Standard are surges due to direct or indirect lightning on the telecommunication line plant. Overvoltages or overcurrent not covered by this European Standard are – short-term induction of alternating voltages from electric power systems (including electrified railway), – earth potential rise due to power faults or load switching, – direct contacts between telecommunication lines and low voltage power lines. This European Standard is intended for use by network (public/private) operators and the equipment manufacturers. This European Standard applies to equipment having telecommunication port(s) connected to external conductors, i.e. conductor located outside the customer’s building. The tests are type tests and, although they are applicable to a complete system, it is recognised that they may be applied to individual items of equipment during development and design work.

Resistibility requirements to overvoltages and overcurrents due to lightning for equipment having telecommunication ports

DL/T 5408-2009 发电厂、变电站电子信息系统220/380V电源电涌保护配置、安装及验收规程

本规程规定了发电厂、变电站(含箱式变电站)电子信息系统220/380V电源电涌保护器的选择、配置原则。 本规程适用于发电厂、变电站 (含箱式变电站)电子信息系统220/380V电源电涌保护器的选择、配置、安装及验收。

Specifications for disposition, erection and acceptance of 220/380V power surge protection in power plant and substation

DIN EN 61230:2009 带电作业.便携式接地或接地短路装置(IEC 61230:2008),德文版本EN 61230:2008

Live working - Portable equipment for earthing or earthing and short-circuiting (IEC 61230:2008); German version EN 61230:2008

NF C18-407*NF EN 50508:2009 高电压安装时的电气操作用多功能绝缘棒

Multi-purpose insulating sticks for electrical operations on high voltage installations.

NF C05-100:2009 电工产品.6种受控物质(铅,汞,镉,六价铬,多溴联苯,多溴联苯醚)水平的测定

Electrotechnical products - Determination of levels of six regulated substances (lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, polybrominated diphenyl ethers).

NF C42-198-11*NF EN 61557-11:2009 最高可达 1000 V 交流电和 1500 V 直流电的低压配电系统的电气安全性.防护测量的试验、测量或监测设备.第11部分:电气配电网接地 TT、TN、IT系统中A型和B型残余电流监测器(RCMs)的效能

Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 11 : Effectiveness of residual current monitors (RCMs) type A and type B in TT, TN and

NF C42-198-9:2009 1000V交流和1500V直流以下的低压配电系统的电气安全性.防护测量用试验,测量或监测设备.第9部分:IT系统中绝缘失效定位设备

Electrical safety in low voltage distribution systems up to 1 000 V ac and 1 500 V dc - Equipment for testing, measuring or monitoring of protective measures - Part 9 : equipment for insulation fault location in IT systems.

BS EN 61557-9:2009 不超过1000 V交流和1500 V直流的低压分布系统的电气安全性.防护措施测试,测量和监控设备.第9部分:IT系统中绝缘故障的定位设备

This part of IEC 61557 specifies the requirements for insulation fault location systems which localize insulation faults in any part of the system in unearthed IT a.c. systems and unearthed IT a.c. systems with galvanically connected d.c. circuits having nominal voltages up to 1 000 V a.c., as well as in unearthed IT d.c. systems with voltages up to 1 500 V d.c., independent of the measuring principle. NOTE 1 IT systems are described in IEC 60364-4-41 amongst other literature. Additional data for a selection of devices in other standards should be noted. NOTE 2 Further information on insulation fault location can be found in the following standards: IEC 60364-4-41:2005, 411.6, and IEC 60364-5-53:2001, 531.3.

Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c.. Equipment for testing, measuring or monitoring of protective measures - Part 9: Equipment for insulation fault location in IT systems

DIN EN 61318:2009 带电作业.工具、器件和设备质量合格评定

Live working - Conformity assessment applicable to tools, devices and equipment (IEC 61318:2007); German version EN 61318:2008