K45 继电保护及自动装置 标准查询与下载

DL/T 623-2010 电力系统继电保护及安全自动装置运行评价规程

本标准规定了电力系统继电保护及安全自动装置的运行评价方法。 本标准适用于接入电网运行的220kV及以上继电保护的运行评价，110kV及以下继电保护的运行评价可参照执行。

Evaluation rules of protection equipment and power system stability control devices

IEC 60099-8:2011 电涌放电器.第8部分:高于1 kV的直流系统的高架输电和配电用带有外部串联火花间隙(EGLA)的金属氧化物电涌放电器

This part of IEC 60099 covers metal-oxide surge arresters with external series gap (externally gapped line arresters (EGLA) that are applied on overhead transmission and distribution lines, only to protect insulator assemblies from lightning-caused flashovers. This standard defines surge arresters to protect the insulator assembly from lightning-caused overvoltages only. Therefore, and since the metal-oxide resistors are not permanently connected to the line, the following items are not considered for this standard: ? switching impulse sparkover voltage; ? residual voltage at steep current and switching current impulse; ? thermal stability; ? long-duration current impulse withstand duty; ? power-frequency voltage versus time characteristics of an arrester; ? disconnector test; ? aging duties by power-frequency voltage. Considering the particular design concept and the special application on overhead transmission and distribution lines, some unique requirements and tests are introduced, such as the verification test for coordination between insulator withstand and EGLA protective level, the follow current interrupting test, mechanical load tests, etc. Designs with the EGLA's external series gap installed in parallel to an insulator are not covered by this standard.

Surge arresters - Part 8: Metal-oxide surge arresters with external series gap (EGLA) for overhead transmission and distribution lines of a.c. systems above 1 kV

DIN CLC/TS 50539-22:2010 低电压浪涌保护设备.含直流电的专门应用浪涌保护设备.第22部分:选择和应用原则.风力涡轮机的应用.德文版本CLC/TS 50539-22-2010

Low-voltage surge protective devices - Surge protective devices for specific application including d.c. - Part 22: Selection and application principles - Wind turbine applications; German version CLC/TS 50539-22:2010

DIN CLC/TS 50539-12:2010 低电压浪涌保护设备.含直流电的专门应用浪涌保护设备.第12部分:筛选和应用原则.连接到广电装置的SPDs.德文版本CLC/TS 50539-12-2010

Low-voltage surge protective devices - Surge protective devices for specific application including d.c. - Part 12: Selection and application principles - SPDs connected to photovoltaic installations; German version CLC/TS 50539-12:2010

DL/T 364-2010 光纤通道传输保护信息通用技术条件

本标准规定了继电保护装置与通信设备的接口、接口连接、保护通道构成方式、继电保护专业和电力通信专业的相关技术原则、光纤通道传输继电保护信息的可靠性指标，以及保护用光纤通道的配置及维护。 本标准适用于220kv及以上电压等级电网传输继电保护信息的光纤通道。110kV电网传输继电保护信息的光纤通道可参照本标准。

General specification of transmitting protection information on optical channel

BS EN 60282-1:2009 高压熔断器.限流熔断器

This part of IEC 60282 applies to all types of high-voltage current-limiting fuses designed for use outdoors or indoors on alternating current systems of 50 Hz and 60 Hz and of rated voltages exceeding 1 000 V. Some fuses are provided with fuse-links equipped with an indicating device or a striker. These fuses come within the scope of this standard, but the correct operation of the striker in combination with the tripping mechanism of the switching device is outside the scope of this standard; see IEC 62271-105.

High-voltage fuses - Current-limiting fuses

JB/T 11050-2010 交流固态继电器

本标准规定了交流固态继电器的型式、尺寸、额定值、特性、测试方法、检验规则、标志、包装和贮存等要求。 本标准适用于额定通态电流(I)至l 000A、额定断态电压(V)至600 V的交流固态继电器。

AC Solid-state relays

DIN EN 60099-4:2010 电涌放电器.第4部分:交流电系统用无间隙金属氧化物电涌放电器

This part of IEC 60099 applies to non-linear metal-oxide resistor type surge arresters without spark gaps designed to limit voltage surges on a.c. power circuits.

Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems (IEC 60099-4:2004, modified + A1:2006 + A2:2009); German version EN 60099-4:2004 + A1:2006 + A2:2009

IEC 60282-1:2009 高压熔断器.第1部分:限流熔断器

This part of IEC 60282 applies to all types of high-voltage current-limiting fuses designed for use outdoors or indoors on alternating current systems of 50 Hz and 60 Hz and of rated voltages exceeding 1 000 V. Some fuses are provided with fuse-links equipped with an indicating device or a striker. These fuses come within the scope of this standard@ but the correct operation of the striker in combination with the tripping mechanism of the switching device is outside the scope of this standard; see IEC 62271-105.

High-voltage fuses - Part 1: Current-limiting fuses

BS DD CLC/TS 61496-2:2006 机械安全性.电敏保护设备.第2部分:利用有源光电防护装置(AOPDs)的设备详细要求

This clause of Part 1 is replaced by the following: This part of IEC 61496 specifies requirements for the design, construction and testing of electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety-related system, employing active opto-electronic protective devices (AOPDs) for the sensing function. Special attention is directed to features which ensure that an appropriate safety-related performance is achieved. An ESPE may include optional safety-related functions, the requirements for which are given in Annex A of IEC 61946-1 and of this part. This part does not specify the dimensions or configurations of the detection zone and its disposition in relation to hazardous parts for any particular application, nor what constitutes a hazardous state of any machine. It is restricted to the functioning of the ESPE and how it interfaces with the machine. Excluded from this part are AOPDs employing radiation at wavelengths outside the range 400 nm to 1500 nm. This part may be relevant to applications other than those for the protection of persons, for example, the protection of machinery or products from mechanical damage. In those applications, additional requirements may be necessary, for example, when the materials that are to be recognized by the sensing function have different properties from those of persons. This part does not deal with EMC emission requirements.

Safety of machinery — Electro-sensitive protective equipment — Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)

IEEE NESC IR553-2008 第38节:法规384C设备接地与连接

Interpretation Section 38. Equipment Rule 384C Grounding and bonding (2007 Edition, page 243) (29 October 2008) IR553

Interpretation Section 38. Equipment Rule 384C Grounding and bonding (2007 Edition, page 243) (29 October 2008) IR553

DIN EN 60255-22-1:2008 测量继电器和保护设备.第22-1部分:电气干扰试验.1MHz脉冲抗扰性试验

Measuring relays and protection equipment - Part 22-1: Electrical disturbance tests - 1 MHz burst immunity tests (IEC 60255-22-1:2007); German version EN 60255-22-1:2008

DL/T 1075-2007 数字式保护测控装置通用技术条件

本标准规定了数字式保护测控装置的术语和定义、技术要求、试验、检验规则、标志、包装、运输及贮存。 本标准适用于3kV～66kV电压等级线路、电容器、变压器、电抗器、电动机等电气设备的数字式保护测控装置(以下简称“装置”)，作为这些装置设计、制造、试验和使用的依据。 对于应用于其他场合的装置，可参考使用本标准。

General specifications for numerical integrated protection and control equipment

DL/T 559-2007 220kV～750kV电网继电保护装置运行整定规程

本标准规定了220kV～750kV电网的线路、断电器、母线以及与电网保护配合有关的变压器、高压电抗器、串联补偿器等电力设备继电保护整定及运行要求。 本标准适用于220kV～750kV电网的线路、断电器、母线以及与电网保护配合有关的变压器、高压电抗器、串联补偿器等电力设备继电保护设备。

Setting guide for 220kV~750kV power system protection equipment

DL/T 584-2007 3kV～110kV电网继电保护装置运行整定规程

本标准规定了3kV～110kV继电保护运行整定的原则、方法和具体要求。 本标准适用于3kV～110kV电网的线路、母线、并联电容器、并联电抗器以及变压器保护中与电网设计、研究制造、安装调试单位及部门亦应遵守本标准。 本标准以微机型继电保护和安全自动装置为主要对象，对于非微机装置可参照执行。

Setting guide for 3kV～110kV power system protection equipment

DL/T 587-2007 微机继电保护装置运行管理规程

本标准规定了微机继电保护装置在技术管理、检验管理、运行管理和职责分工等方面的要求。 本标准适用于10kV及以上电力系统中电力主设备和线路的微机继电保护装置。

Code for operating management of microprocessor-based relaying protection equipment

ANSI/IEEE 142:2007 工业和商业电力系统接地的推荐实施规程

The problems of system grounding, that is, connection to ground of neutral, of the corner of the delta, or of the midtap of one phase, are covered. The document covers the grounding of various systems, equipment grounding, static and lightning protection grounding, connection to earth, and electronic equipment grounding.

Recommended Practice for Grounding of Industrial and Commercial Power Systems

SANS 60099-5:2007 电涌放电器．第5部分：选择和应用建议

Provides recommendations for the selection and application of surge arresters to be used in three-phase systems with nominal voltages above 1 kV. Applies to non-linear resistor type gapped surge arresters and to gapless metal-oxide surge arresters.

Surge arresters Part 5: Selection and application recommendations

DIN CLC/TS 61643-12:2007 低压电涌保护装置.第12部分:与低压电力系统连接的电涌保护装置.选择和应用原则

Low-voltage surge protective devices - Part 12: Surge protective devices connected to low-voltage power systems - Selection and application principles (IEC 61643-12:2002, modified); German version CLC/TS 61643-12:2006

UL 467-2007 接地和连接设备

This Standard applies to grounding and bonding equipment for use in accordance with the Canadian Electrical Code, Part I, CSA C22.1, in Canada or the National Electrical Code, NFPA 70, in the United States. This Standard applies to the following grounding and bonding equipment: a) ground clamps, bonding devices, grounding bushings, water-meter shunts, grounding electrodes, and the like used in a grounding system; b) equipment for making electrical connections between i) the grounding conductors used in electrical power systems, non-current-carrying metal parts of electrical equipment, armored grounding wires, metal raceways, and the like; and ii) grounding electrodes; c) equipment for making electrical connections between i) the grounding conductors used in telecommunications systems such as telephone, radio, CATV, network power broadband, and the like; and ii) grounding electrodes; and d) hospital grounding jacks and mating grounding cord assemblies (for the United States, see Annex a).

Grounding and bonding equipment