K49 避雷器 标准查询与下载

IEC 62561-7:2018 避雷装备部件(LPSC). 第7部分: 增强性化合物的接地要求

This part of IEC 62561 specifies the requirements and tests for earthing enhancing compounds producing low resistance of an earth termination system.

Lightning protection system components (LPSC) - Part 7: Requirements for earthing enhancing compounds

YD/T 3285-2017 无线电监测站雷电防护技术要求

Technical requirements for lightning protection of radio monitoring stations

BS EN 62561-1:2017 避雷系统组件(LPSC).连接组件的要求

Lightning protection system components (LPSC). Requirements for connection components

IEC 62561-4:2017 雷电防护系统组件(LPSC).第4部分:导体紧固件用要求

This part of IEC 62561 deals with the requirements and tests for metallic and non-metallic conductor fasteners that are used to retain and support the air-termination, down-conductor and earth-termination systems. This document does not cover the fixing of conductor fasteners to the fabric of structures due to the vast number and types used in modern day construction. LPSC can also be suitable for use in hazardous atmospheres. There are therefore additional requirements when installing the components in such conditions.

Lightning protection system components (LPSC) - Part 4: Requirements for conductor fasteners

IEC 62561-5:2017 雷电防护系统组件(LPSC).第5部分:接地极检测箱和接地电极密封要求

This part of IEC 62561 specifies the requirements and tests for earth electrode inspection housings (earth housing) installed in the earth and for earth electrode seals. Lightning protection system components (LPSC) can also be suitable for use in hazardous atmospheres. There are therefore additional requirements when installing the components under such conditions. NOTE Different requirements and test procedures are given in EN 124 (all parts) and EN 1253 (all parts).

Lightning protection system components (LPSC) - Part 5: Requirements for earth electrode inspection housings and earth electrode seals

IEC 62561-3:2017 避雷系统组件(LPSC).第3部分:隔离火花间隙的要求(ISG)

This part of IEC 62561 specifies the requirements and tests for isolating spark gaps (ISG) for lightning protection systems. ISGs can be used to indirectly bond a lightning protection system to other nearby metalwork where a direct bond is not permissible for functional reasons. Typical applications include the connection to earth-termination systems of power installations; earth-termination systems of telecommunication systems; auxiliary earth electrodes of voltage-operated, earth fault circuit breakers; rail earth electrode of power and DC railways; measuring earth electrodes for laboratories; installations with cathodic protection and stray current systems; service entry masts for low-voltage overhead cables; bypassing insulated flanges and insulated couplings of pipelines. This does not cover applications where follow currents occur. NOTE Lightning protection system components (LPSC) can also be suitable for use in hazardous conditions such as fire and explosive atmosphere. Due regard will be taken of the extra requirements necessary for the components to be installed in such conditions.

Lightning protection system components (LPSC) - Part 3: Requirements for isolating spark gaps (ISG)

DL/T 1694.5-2017 高压测试仪器及设备校准规范 第5部分：氧化锌避雷器阻性电流测试仪

Calibration specifications for high-voltage testing instruments and equipment Part 5: Zinc oxide arrester resistive current tester

IEC 62561-1:2017 避雷系统组件(LPSC).第1部分:连接组件的要求

This part of IEC 62561 specifies the requirements and tests for metallic connection components that form part of a lightning protection system (LPS). Typically, these can be connectors, clamps, bonding and bridging components, expansion pieces and test joints. For the purposes of this document the following connection types are considered as connection components: exothermic, brazing, welding, clamping, crimping, seaming, screwing or bolting. Testing of components for an explosive atmosphere is not covered by this document.

Lightning protection system components (LPSC) - Part 1: Requirements for connection components

DL/T 1677-2016 电力工程用降阻接地模块技术条件

Technical conditions for resistance-reducing grounding modules for power engineering

DL/T 1676-2016 交流输电线路用避雷器选用导则

Guidelines for Selection of Surge Arresters for AC Transmission Lines

JIS Z 9290-4:2016 防雷电.第4部分:建筑物中电气和电子系统

Protection against lightning -- Part 4: Electrical and electronic systems within structures

NF C17-153-1:2016 雷电防护系统部件(LPC).第1部分:连接部件的要求

Lightning protection system components (LPSC) - Part 1 : requirements for connection components

DL/T 1561-2016 避雷器监测装置校准规范

Calibration specification for arrester monitoring device

DL/T 1432.3-2016 变电设备在线监测装置检验规范 第3部分：电容型设备及金属氧化物避雷器绝缘在线监测装置

本部分规定了电容型设备及金属氧化物避雷器绝缘在线监测装置的检验项目、检测条件、检验内容及要求和检验结果处理。 本部分适用于电容型设备及金属氧化物避雷器绝缘在线监测装置的型式试验、出厂试验、交接试验和现场试验。

Testing specification for on-line monitoring device of transformation equipment.Part 3: On-line insulation monitoring device of capacitive equipment and metal-oxide surge arrester

BS EN 62858:2015 基于闪电定位系统 (LLS) 的闪电密度. 通用原则

Lightning density based on lightning location systems (LLS). General principles

NB/T 42059-2015 交流电力系统金属氧化物避雷器用脱离器

本标准规定了额定电压大于lkV的交流电力系统金属氧化物避雷器用脱离器(以下简称脱离器)的技术要求、试验方法和检验规则等内容。本标准仅适用于将故障避雷器从交流系统中退出并能明显识别而设计的脱离器。

Disconnectors of metal-oxide surge arresters for a.c. systems

DB43/T 1085-2015 电梯防雷技术规范

Elevator Lightning Protection Technical Specifications

IEC 62858:2015 基于闪电定位系统 (LLS) 的闪电密度. 通用原则

This International Standard introduces and discusses all necessary measures to make reliable and homogeneous the values of NG obtained from LLS in various countries. Only parameters that are relevant to risk assessment are considered.

Lightning density based on lightning location systems (LLS) - General principles

NB/T 42049-2015 3kV及以下直流系统用无间隙金属氧化物避雷器

本标准规定了额定电压4.8kV及以下瓷外套和复合外套直流无间隙金属氧化物避雷器(以下简称避雷器)的技术要求、试验方法和检验规则等内容。本标准适用于3kV及以下直流系统中保护牵引电机及电气设备免受过电压损坏的避雷器。

Metal-oxide surge arresters without gaps for d.c. systems of 3kV and below

JIS C 4608:2015 6.6 kV室内单元变电所用避雷装置

Surge arresters for 6.6 kV cubicle type unit substation