共找到 3934 条与 连接器 相关的标准,共 263 页
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for strain relief (IEC 61300-2-42:2014); German version EN 61300-2-42:2014
Connectors for electronic equipment. Product requirements. Circular connectors. Detail specification for connectors with M 12 × 1 screw-locking, for data transmission frequencies up to 500 MHz
Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Tests. Screen testing of return loss of single-mode PC optical fibre connectors
Radio-frequency connectors. Sectional specification for series SQMA series quick lock RF coaxial connectors
Fibre optic interconnecting devices and passive components. Performance standard. Non-connectorized single-mode fibre optic middle-scale 1 x N DWDM devices for category C. Controlled environments
Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Tests. Cable nutation
Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 17-1: Type FPFT (factory polished field terminated) simplex connector factory terminated with EN 60793-2-50 category B1.3 fibre an
Dynamic modules. Design guide. Investigation of operating mechanical shock and vibration tests for dynamic modules
本标准规定了TVS瞬态保护电连接器的要求和验证等。 本标准适用于TVS瞬态保护电连接器(以下简称电连接器)的设计、制造和检验。
General requirements for TVS transient protection connectors
Industrial connector sets and interconnect components to be used in optical fibre control and communication systems. Product specifications. Type ODVA APC terminated on EN 60793-2-50 category B1.1 and B1.3 singlemode fibre to meet the requirements of cate
Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Examinations and measurements. Switching time
Connectors for electronic equipment.Tests and measurements.Part 15-6: Connector tests (mechanical tests).Test 15f: Effectiveness of connector coupling devices
Method for test of connectors for use in electronic equipment (Amendment 1)
Connectors for electronic equipment -- Tests and measurements -- Part 13-5: Mechanical operation tests -- Test 13e: Polarizing and keying method
Connectors for electronic equipment -- Tests and measurements -- Part 15-4: Connector tests (mechanical tests) -- Test 15d: Contact insertion, release and extraction force
Connectors for electronic equipment -- Tests and measurements -- Part 16-3: Mechanical tests on contacts and terminations -- Test 16c: Contact-bending strength
Connectors for electronic equipment.Tests and measurements.Part 15-1: Connector tests (mechanical).Test 15a: Contact retention in insert
Connectors for electronic equipment.Tests and measurements.Part 1-100: General.Applicable publications
"This part of IEC 62196 is applicable to vehicle couplers with pins and contact-tubes of standardized configuration@ herein also referred to as ""accessories""@ intended for use in electric vehicle conductive charging systems which incorporate control means@ with rated operating voltage up to 1 500 V d.c. and rated current up to 250 A@ and 1 000 V a.c. and rated current up to 250 A. This part of IEC 62196 applies to high power d.c. interfaces and combined a.c./d.c. interfaces of vehicle couplers specified in IEC 62196-1:2014@ and intended for use in conductive charging systems for circuits specified in IEC 61851-1:2010@ and IEC 61851-23:2014. The d.c. vehicle connectors covered by this part of the standard are used only in charging mode 4@ according to Case C in Clause 6.2 of IEC 61851-1:2010@ Figure 3 in Clause 6.3.1 of IEC 61851-1:2010 and IEC 62196-2:2011. The d.c. vehicle inlets covered by this part of the standard are used only in charging mode 4@ according to Case C in Clause 6.2 of IEC 61851-1:2010@ Figure 3 in Clause 6.3.1 of IEC 61851-1:2010. These vehicle couplers are intended to be used for circuits similar to those specified in IEC 61851-23 which operate at different voltages and which may include ELV and communication signals. This part of IEC 62196 applies to the vehicle couplers to be used in an ambient temperature of between ?C30 ??and +50 ?? NOTE 1 In some countries@ other requirements may apply. NOTE 2 In the following country@ ?C35 ??applies: SE. These vehicle couplers are intended to be connected only to cables with copper or copperalloy conductors."
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
This part of IEC 61076 describes circular connectors with IP 65/IP 67 degree of protection and suitable for data transmission with frequencies up to 500 MHz. Applications include@ but are not limited to@ vision systems and data acquisition. These connectors consist of fixed and free connectors@ either rewireable or non-rewireable@ with M12 x 1 screw-locking. Male connectors have round contacts?? 0@6 mm. This standard covers two different types of connectors@ denominated X and H@ with different contact arrangement@ not mutually interchangeable@ but with common ratings and purposes.
Connectors for electronic equipment - Product requirements - Part 2-109: Circular connectors - Detail specification for connectors M 12 × 1 with screw-locking, for data transmissions with frequencies up to 500 MHz
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号