共找到 3934 条与 连接器 相关的标准,共 263 页
Radio-frequency connectors - Part 47: Sectional specification for radio-frequency coaxial connectors with clamp coupling, typically for use in 75 ? cable networks (type F-Quick) (IEC 61169-47:2015); German version EN 61169-47:2015
本规范规定了N系列射频同轴连接器(以下简称连接器)的详细要求。 本规范适用的连接器及其型号与图表号的对照表参见附录A。
Detail specification for seriesN radio frequency coaxial connector
本规范规定了TNC系列2级射频同轴连接器的详细要求。 本规范适用于TNC系列2级射频同轴连接器,本规范适用的连接器及其型号与图号、表号的对照参见附录A。
Detail specification for series TNC radio frequency coaxial connector
Connectors for printed boards with frequencies below 3 MHZ Part 11: Detailed specifications for coaxial connectors (free connectors and fixed connector dimensions)
Plugs and socket-outlets for household and similar purposes - Part 1: General requirements on fixed socket-outlets
Plugs and socket-outlets for household and similar purposes - Part 2-1: General requirements on Plugs and portable socket-outlets
5.1 This practice is based on the use of electrical resistance as an indicator of contact performance. This is the fundamental physical attribute that reflects the condition of the electrical contact interface(s) within a connection. For practical current-carrying electrical connections, resistance may be calculated from potential drop measurements, as described, for example, in Test Method B539 and B812. 5.2 This practice accommodates the use of multiple test methods, as may be required to predict performance in a given application. 5.3 This practice applies only to the performance of the current-carrying contact interface(s). It does not characterize the performance of insulating materials or other components of a complete connection system. 5.4 Specifiers may use the performance classification as a requirement for a given application. 5.5 Manufacturers may use the performance classification to reflect the relative quality of their products. 1.1 This practice provides a method of specifying performance requirements for (or reporting test results of) electrical contact and connection systems. Both conductor and connector system performance may be specified by this practice, separately or in combination. 1.2 This practice may be used for separable or permanent contacts employing metallic conducting components. 1.3 This practice is applicable to both signal and power applications. 1.4 This practice is intended to be used for specifying performance of connectors and connection systems that are marketed for general public and trade application, as for instance for use in building wiring, electronics, and vehicles. 1.5 This practice is not intended to be used to specifying the performance of connection systems for specialized applications, such as military, industrial, aircraft, power distribution, and medical apparatus. 1.6 This practice does not specify the sample preparation or test sequences required for determining contact performance. It is the responsibility of the user of this practice to determine the applied test sequence(s) appropriate for the application. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provide by the manufacturer, to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Practice for Contact Performance Classification of Electrical Connection Systems
The Common Test Interface Pin Map Configuration for High-Density, Single-Tier Electronics Test Requirements Utilizing IEEE Std 1505
Connectors for electronic equipment -- Product requirements -- Part 1: Generic specification
Connectors for electronic equipment -- Tests and measurements -- Part 13-1: Mechanical operation tests -- Test 13a: Engaging and separating forces
本标准规定了250V及以下免剥皮快速电线连接器的术语和定义、一般要求、产品分类、产品型号与表示方法、性能要求、检验方法、检验规则、标签和标志、包装、运输及贮存。 本标准适用于0.5mm2 ~6.0mm2 250V及以下免剥皮快速电线连接器,不适用于防水,不能重复使用。
250V and below non-stripping fast wire connector
This International Standard establishes specifications and test requirements for a high-speed two-part connector with integrated shielding function for use as a printed board connector in industrial environments. The connectors connect a backplane to printed boards.
Connectors for electronic equipment - Product requirements - Part 4-116: Printed board connectors - Detail specification for a high-speed two-part connector with integrated shielding function
Radio-frequency connectors. Sectional specification for series MMCX RF coaxial connectors
The Universal Test Interface Framework and Pin Configuration for Portable/Benchtop Test Requirements Utilizing IEEE 1505 Receiver Fixture Interface Standard
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-14: Examinations and measurements - Error and repeatability of the attenuation settings of a variable optical attenuator (IEC 61300-3-14:2014); Ger
Direct current (DC) plugs and socket-outlets for information and communication technology (ICT) equipment installed in data centres and telecom central offices Part 1: Plug and socket-outlet system for 2,6 kW
Radio-frequency connectors. Sectional specification for radio-frequency coaxial connectors with clamp coupling, typically for use in 75
Space product assurance - Wire wrapping of high-reliability electrical connections; English version EN 16602-70-30:2014
Cylindrical cavity method to measure the complex permittivity of low-loss dielectric rods
Radio-frequency connectors. Sectional specification for RF coaxial connectors with inner diameter of outer conductors 13,5 mm with bayonet lock. Characteristic impedance 50 O (type QLI)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号