共找到 139 条与 收、发信管 相关的标准,共 10 页
Harmonized system of quality assessment for electronic components; blank detail specification: small power transmitting tubes of anode dissipation up to 1 kW
This specification covers two compositions of aluminum pigmented, heatresistant,paint that will withstand solvents, normal weather exposure, and temperatures up to 650° Celsius ( C ) , and will maintain an emissivity factor below 0.40.
PAINT, ALUMINUM, HEAT-RESISTING (650 DEG. C), LOW-EMISSIVITY (0.40 OR LESS) (METRIC)
This specification establishes the requirements for the procurement of Surface Vessel Torpedo Tube Mk 32 Mod 9 (NAVORD LD 621171).
TORPEDO TUBE, SURFACE VESSEL, MARK 32 MOD 9 (FOR TORPEDOES MK 44 MOD 1 AND MK 46 MOD 1)
This specification establishes the requirements for the procurement of Torpedo Tube Assembly Mk 32 Mod 5 (NAVSEA LD 162165) and Torpedo Tube Assembly Mk 32 Mod 7 (NAVSFA LD 162166) for use on surface vessels.
TORPEDO TUBE, SURFACE VESSEL, MARK 32 MODS 5 AND 7 (FOR TORPEDOES MARK 44 MOD 1 AND MARK 46 MOD 1)
that frequency-shift keying is employed in radiotelegraphy in the fixed service
FREQUENCY-SHIFT KEYING
Generic specification for receiving tubes,high reliability, subminiature and finger-shaped
ELECTRONIC TUBES WITH QUALITY CONFORMANCE PROCEDURES. TRANSMITTING AND RECEIVING CLASSICAL TUBES. PARTICULAR REQUIREMENTS.
1.1 This practice covers the definition and interpretation of the commonly used thermionic constants of electron emitters (1, 2, 3), with appended standard methods of measurement.
Standard Practice for Definition and Determination of Thermionic Constants of Electron Emitters
1.1 This practice covers the definition and interpretation of the commonly used thermionic constants of electron emitters (1, 2, 3), with appended standard methods of measurement.
Standard Practice for Definition and Determination of Thermionic Constants of Electron Emitters
This specification covers Firing Mechanism 29378-1. The-assembly w i l l be used to activate the canopy counter balance jettison and clnch dom cylinder assembly in the TF-102 Aircraft
FIRING MECHANISM, CARTRIDGE ACTUATED: 29378-1 ASSEMBLY
This specification covers Firing Mechanisms P/N 29378-1. The assembly w i l l be ultimately loaded and used to actuate the canopy counterbalance jettison and cinch-down cylinder assembly in the TF102 Aircraft.
FIRING MECHANISM, CARTRIDGE ACTUATED, 29378-1 REMANUFACTURED METAL PARTS ASSEMBLY
This specification covers Firing Mechanisms P/N 50057-1. The assembly w i l l be ultimately loaded and used t o actuate the canopy counterbalance jettison and cinch-down cylinder assembly in the F102 Aircraft.
FIRING MECHANISM, CARTRIDGE ACTUATED, 50057-1 REMANUFACTURED METAL PARTS ASSEMBLY
This specification covers Firing Mechanism 50057-1, The assembly wl be used t o activate the canopy counter balance jettison and cinch down cylinder assembly in the F102 Aircraft.
FIRING MECHANISM, CARTRIDGE ACTUATED, 50057-1 ASSEMBLY
This specification describes the requirements for the procurenient, inspection, and testing
RELAY PANEL, FIRING (FOR TORPEDO MARK 37 MODS 0, 2, AND 3)
Orderhg data, - Procurement documents should specify the following:
GROMMET, FIBER (FOR PROJECTILE ROTATING BANDS)
This amendment forms a part of Specification MIL-Po17959(Nord), dated 6 April 1954.
POWDER, PROPELLANT, BALLISTICS OF, FOR 3 INCH 50 CALIBER GUN
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号