N13 机械量仪表、自动秤重装置与其他检测仪表 标准查询与下载

JJG 233-2008 压电加速度计检定规程

本规程适用于压电加速度计（以下简称加速度计）的首次检定、后续检定和使用中检验。

Verification Regulation for Piezoelectric Accelerometer

JIS B 7613:2008 家用计量器.浴室体重计、儿童体重计和烹饪用秤

この規格は，主として家庭で使用されるはかりであって，ひょう量が20 kgを超え，200 kg以下の一般用体重計，ひょう量が20 kg以下の乳幼児用体重計及びひょう量が3kg以下の調理用はかりについて規定する。

Household scales -- Bathroom scales, baby scales and cooking scales

ASME B89.4.10360.2-2008 坐标测量机(CMMs)用验收试验和重新认证试验.第2部分:线性尺寸测量用CMMs(技术报告)

This part of ISO 10360 specifies the acceptance tests for verifying the performance of a CMM usedfor measuring linear dimensions as stated by the manufacturer. It also specifies the reverificationtests that enable the user to periodically reverify the performance of the CMM.The acceptance and reverification tests given in this part of ISO 10360 are applicable only toCartesian CMMs using contacting probing systems of any type operating in the discrete-point probingmode.This International Standard does not explicitly apply to:—non-cartesian CMMs, however, the parties may apply this part of 10360 to non-Cartesian CMMsby mutual agreement,—CMMs using optical probing, however, the parties may apply this approach to optical CMMs bymutual agreement.This International Standard specifies performance requirements that can be assigned by themanufacturer or the user of a CMM, the manner of execution of the acceptance and reverificationtests to demonstrate the stated requirements, rules for proving conformance, and applications forwhich the acceptance and reverification tests can be used.

Acceptance Test and Reverification Test for Coordinate Measuring Machines (CMMs) Part 2: CMMs Used for Measuring Linear Dimensions (Technical Report)

DIN EN ISO 14978 Berichtigung 1:2008 几何产品规范(GPS).GPS测量设备的一般概念和要求.技术勘误DIN EN ISO 14978-2006-11

Geometrical product specifikations (GPS) - General concepts and requirements for GPS measuring equipment (ISO 14978:2006); German version EN ISO 14978:2006, Corrigendum to DIN EN ISO 14978:2006-11; German version EN ISO 14978:2006/AC:2008

JJG 264-2008 容重器检定规程

本规程适用于容重器首次检定、后续检定和使用中的检验。

Verification Regulation of Measuring Instruments for Cereals Density

JJF 1196-2008 机动车方向盘转向力-转向角检测仪校准规范

本规范适用于机动车方向盘转向力-转向角检测仪（以下简称方向盘力角仪）的校准。 本规范规定了方向盘力角仪的计量特性及校准方法。

Calibration Specification of Motor Vehicle Testers for Steering Force and Steering Angle

JIS B 7612-1:2008 重量测量仪的测压元件.第1部分:类似用途的测压元件

この規格は，ひずみゲージを用いた質量計用ロードセル(以下，ロードセルという。)について規定する。

Load Cells for Weighing Instruments -- Part 1: Analog Load Cells

JB/T 6788-2008 机械计数器系列型谱

本标准规定了机械计数器系列型谱。 本标准适用于纯机械计数器（以下简称计数器）。

Spectrum for type of temperature sensor

ISO 14978:2006/cor 1:2008 产品几何量技术规范(GPS).产品几何量技术规范(GPS)测量设备的一般概念和要求.技术勘误表1

This standard is Geometrical product specifications (GPS) - General concepts and requirements for GPS measuring equipment; Technical Corrigendum 1

Geometrical product specifications (GPS) - General concepts and requirements for GPS measuring equipment; Technical Corrigendum 1

JIS B 7609:2008 砝码

この規格は，質量測定の信頼性を確保するための標準として，又ははかりとともに用いる，質量の公称値が1 mg～5 000kgまでの分銅について，精度等級（E級，E級，F級，F級，M級，M級，M級，M）に分けて規定する。

Weights

GOST R 53228-2008 非自动称重仪器.第1部分:计量学和技术要求.试验

Non-automatic weighing instruments. Part 1. Metrological and technical requirements. Tests

ANSI/IEEE 1293/Cor1:2008 线性单轴非回转仪加速计用标准规范格式指南和试验程序.技术勘误1:附录K&L变化

Standard Specification Format Guide and Test Procedure for Linear, Single-Axis, Non-Gyroscopic Accelerometers - Corrigendum 1: Annex K & L Changes

ASTM E2428-08 验证扭矩试验机力矩指示用扭矩测量仪校准的标准实施规程

Testing machines that apply and indicate torque are in general use in many industries. Practice WK6364 has been written to provide a practice for the torque verification of these machines. A necessary element in Practice WK6364 is the use of devices whose torque characteristics are known to be traceable to national standards. Practice E 2428 describes how these devices are to be calibrated. The procedures are useful to users of torque testing machines, manufacturers and providers of torque measuring instruments, calibration laboratories that provide calibration services and documents, and service organizations using devices to verify torque testing machines.1.1 This practice is to specify procedure for the calibration of elastic torque-measuring instruments. Note 18212;Verification by deadweight and a lever arm is an acceptable method of verifying the torque indication of a torque testing machine. Tolerances for weights used are tabulated in Practice WK6364; methods for calibration of the weights are given in NIST Technical Note 577, Methods of Calibrating Weights for Piston Gages. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This practice is intended for the calibration of static or quasi-static torque measuring instruments. The practice is not applicable for high speed torque calibrations or measurements. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Calibration of Torque-Measuring Instruments for Verifying the Torque Indication of Torque Testing Machines

IEEE 1293/COR 1-2008 线性、单轴、无回旋装置加速度计的规范格式指南和试验程序.技术勘误1:附件K和附件L的改变

Specification format guide and test procedure for linear, single-axis, nongyroscopic accelerometers; Corrigendum 1: Changes to annex K and annex L

JJF 1185-2007 速度型滚动轴承振动测量仪校准规范

本规范适用于速度型滚动轴承振动测量仪的校准。

Calibration Specification for Vibrometer (Velocity) of Rolling Bearings

DIN 8127:2007 E₁、E₂、F₁、F₂、M₁、M_1-2、M₂、M_2-3和M₃等级的重量.度量衡学和技术要求

This standard contains technical and metrological requirements for weights used: - as standard for the verification of weighing instruments; - as standards for the verification or calibration of weights of a lower accuracy class; - with weighing instruments.

Weights of classes E₁, E₂, F₁, F₂, M₁, M_1-2, M₂, M_2-3, and M₃ - Metrological and technical requirements (OIML R 111-1:2004)

DIN 8131:2007 自动测重装填仪.度量衡学和技术要求.试验

This International Recommendation specifies the metrological and technical requirements for automatic gravimetric filling instruments," hereinafter called ""filling instruments""", which sub divide a bulk product into fills of predetermined and virtually constant mass by automatic weighing, the fills being kept separate.#,,#

Automatic gravimetric filling instruments - Metrological and technical requirements - Tests (OIML R 61-1:2004)

NAVY QPL-8813-13 NOTICE 2-2007 2型系列液压式飞机放气阀

QPL-8813-13, which identified products qualified under the requirements specified in MIL-V-8813, has been transformed to an equivalent qualification data set (QDS).

VALVE, AIRCRAFT, HYDRAULIC PRESSURE RELIEF, TYPE II SYSTEMS

NAVY QPL-5524-24 NOTICE 1-2007 1型系列飞机液压止回阀

QPL-5524-24, which identified products qualified under the requirements specified in MIL-V-5524, has been transformed to an equivalent qualification data set (QDS). Qualification information previously provided in this List is now available from the Qualified Products Database (QPD).

Valves, Check, Hydraulic, Aircraft, Type 1 Systems

NAVY QPL-5504-35 NOTICE 1-2007 微尘液压式过滤器及过滤器元件

QPL-5504-35, which identified products qualified under the requirements specified in MIL-F-5504, has been transformed to an equivalent qualification data set (QDS).

FILTERS AND FILTER ELEMENTS, FLUID PRESSURE, HYDRAULIC MICRONIC TYPE