N53 电化学、热化学、光学式分析仪器 标准查询与下载

JB/T 9359.1-1999 红外线气体分析器.技术条件

　　本标准规定了红外线气体分析器的要求、试验方法、检验规则、标志、包装、运输和贮存等。 　　本标准适用于连续测定混合气体中某一组分或几种组分的不分光红外线气体分析器。 　　本标准适用于由光学、机械、电气部件组成的完整的仪器。根据本标准的目的，凡仪器附带的或由制造者规定的供仪器使用的稳压电源都属于仪器的一部分，无论其装于仪器内或是单独安装。 　　本标准不适用于与仪器连接使用的试样处理系统或其它附件，如记录仪，模拟数字转换器，数据收集系统等。

Specification of infrared gas analyzers

JB/T 9362-1999 离子选择电极.技术条件

　　本标准规定了离子选择电极的要求、试验方法、检验规则、标志、包装、运输、贮存等。 　　本标准适用于敏感膜类型如下所示规定的钾、钠、氟、氯、氨等五种通用离子选择电极。 　　电极名称 钾电极 钠电极 氟电极 氯电极 氨电极 　　敏感膜类型 PVC膜 玻璃膜 单晶膜 晶体膜 玻璃膜+透气膜 　　电极与适当的参比电极构成化学电池，用于测量水溶液中各种相应的离子浓度。

Specification for ion selective electrodes

JB/T 9359.2-1999 红外线气体分析器.试验方法

　　本标准规定了红外线气体分析器的定义、影响量、性能参数、试验项目及其方法。 　　本标准适用于连续测定环境空气或进入环境空气的气体中某一种或几种气体组分的不分光红外线气体分析器，即包括光学、机械、电气和电子部件的作为整体分析单元的成套分析仪器及配套的稳压电源。 　　本标准不适用于试样处理系统或与分析器联用的纪录器、模拟数字转换器、数据收集系统附件等。

Test method of infrared gas analyzers

JB/T 9365-1999 比较测色计

　　本标准规定了比较测色计的要求、试验方法、检验规则、标志、包装、运输、贮存等。 　　本标准适用于罗维朋单位的比较测色计、罗维朋比色计。

Colorimeter (Tintometer)

HB/Z 5085.7-1999 氰化电镀镉溶液分析方法 原子吸收光谱法测定铁的含量

本标准规定了采用原子吸收光谱法测定氰化电镀镉溶液中铁含量的方法原理、试剂、仪器、分析步骤及分析结果的计算。 　　本标准适用于氰化电镀镉溶液中铁含量的测定。

Analytical method of cadmium electroplating solution in cyanide electroplating Atomic absorption spectrometry Determination of iron content

HB/Z 5085.1-1999 氰化电镀镉溶液分析方法 EDTA容量法测定氧化镉的含量

本标准规定了采用EDTA容量法测定氰化电镀镉溶液中氧化镉含量的方法原理、试剂、分析步骤及分析结果的计算。 　　本标准适用于氰化电镀镉溶液中氧化镉含量的测定。

Analytical method of cadmium electroplating solution in cyanide electroplating EDTA volumetric method to determine the content of cadmium oxide

HB/Z 5085.2-1999 氰化电镀镉溶液分析方法 电位滴定法测定氰化钠的含量

本标准规定了采用电位滴定法测定氰化电镀镉溶液中氰化钠含量的方法原理、试剂、仪器、分析步骤及分析结果的计算。 　　本标准适用于氰化电镀镉溶液中氰化钠含量的测定。

Analytical method of cadmium electroplating solution for cyanide electroplating Determination of sodium cyanide content by potentiometric titration

HB/Z 5085.3-1999 氰化电镀镉溶液分析方法 电位滴定法测定氢氧化钠的含量

本标准规定了采用电位滴定法测定氰化电镀镉溶液中氢氧化钠含量的方法原理、试剂、仪器、分析步骤及分析结果的计算。 　　本标准适用于氰化电镀镉溶液中氢氧化钠含量的测定。

Analytical method of cyanide electroplating cadmium solution Potentiometric titration for determination of sodium hydroxide content

HB/Z 5085.4-1999 氰化电镀镉溶液分析方法 电位滴定法测定碳酸钠的含量

本标准规定了采用电位滴定法测定氰化电镀镉溶液中碳酸钠含量的方法原理、试剂、仪器、分析步骤及分析结果的计算。 　　本标准适用于氰化电镀镉溶液中碳酸钠含量的测定。

Analytical method of cadmium electroplating solution for cyanide electroplating Determination of sodium carbonate content by potentiometric titration

HB/Z 5085.5-1999 氰化电镀镉溶液分析方法 ＥＤＴＡ容量法测定硫酸镍的含量

本标准规定了采用EDTA容量法测定氰化电镀镉溶液中硫酸镍（NiSO4.7H2O）含量的方法原理、试剂、分析步骤及分析结果的计算。 　　本标准适用于氰化电镀镉溶液中硫酸镍含量的测定。

Analytical method for cyanide electroplating cadmium solution Determination of nickel sulfate content by EDTA volumetric method

HB/Z 5085.6-1999 氰化电镀镉溶液分析方法 沉淀滴定法测定硫酸钠的含量

本标准规定了采用沉淀滴定法测定氰化电镀镉溶液中硫酸钠（NaSO4.10H2O）含量的方法原理、试剂、分析步骤及分析结果的计算。 　　本标准适用于氰化电镀镉溶液中硫酸钠含量的测定。

Analytical method for cadmium cyanide electroplating solution Determination of sodium sulfate content by precipitation titration

HB/Z 5085.8-1999 氰化电镀镉溶液分析方法 原子吸收光谱法测定铜的含量

本标准规定了采用原子吸收光谱法测定氰化电镀镉溶液中铜含量的方法原理、试剂、仪器、分析步骤及分析结果的计算。 　　本标准适用于氰化电镀镉溶液中铜含量的测定。

Analytical method of cadmium electroplating solution in cyanide plating Determination of copper content by atomic absorption spectrometry

HB/Z 5088.1-1999 电镀镍溶液分析方法 ＥＤＴＡ容量法测定硫酸镍和硫酸镁的含量

本标准规定了采用EDTA容量测定电镀镍溶液中硫酸镍（NiSO4.7H2O）和硫酸镁（MgSO4.7H2O）含量的方法原理、试剂、分析步骤及分析结果的计算。 　　NiSO4.7H2O120～210g/LMgSO4.7H2O10～50g/L引用文件　HB/Z　5083-78　电镀溶液分析砈檬约?

Electroplating nickel solution analysis method EDTA volumetric method to determine the content of nickel sulfate and magnesium sulfate

HB/Z 5104.1-1999 铝合金硫酸阳极氧化溶液分析方法 电位滴定法测定游离硫酸和化合硫酸的含量

本标准规定了采用电位滴定法测定硫酸阳极氧化溶液中游离硫酸和化合硫酸含量的方法原理、仪器、试剂、分析步骤及分析结果的计算。 　　本标准适用于硫酸阳极氧化溶液中游离硫酸和化合硫酸含量的测定。

Analytical method of aluminum alloy sulfuric acid anodic oxidation solution Potentiometric titration determination of free sulfuric acid and combined sulfuric acid

HB/Z 5104.2-1999 铝合金硫酸阳极氧化溶液分析方法 电位滴定法测定铝的含量

本标准规定了采用电位滴定法测定硫酸阳极氧化溶液中铝含量的方法原理、试剂、仪器、分析步骤及分析结果的计算。 　　本标准适用于硫酸阳极氧化溶液中铝含量的测定。测定范围：20～40g/L

Analytical method of sulfuric acid anodic oxidation solution of aluminum alloy - Determination of aluminum content by potentiometric titration

HB/Z 5108.1-1999 磷化溶液分析方法 电位滴定法测定游离酸度和总酸度

本标准规定了采用电位滴定法测定磷化溶液中游离酸度和总酸度的方法原理、试剂、仪器、分析步骤及分析结果的计算。 　　本标准适用于磷化溶液中游离酸度和总酸度的测定。测量范围：游离酸度3点～20点。总酸度50点～110点。

Analytical methods for phosphating solutions - Potentiometric titration for the determination of free and total acidity

HB/Z 5108.2-1999 磷化溶液分析方法 目视比浊法测定氯离子的含量

本标准规定了采用目视比浊法测定磷化溶液中氯离子含量的方法原理、试剂、分析步骤及分析结果的计算。 　　本标准适用于磷化溶液中氯离子含量的测定。测量范围：0.30～0.60g/L

Analytical method of phosphating solution Determination of chloride ion content by visual turbidimetry

ASTM E1944-98(2007) 描述和测量实验室傅里叶变化近红外线(FT－NIR)光谱分析仪性能的标准实施规程;零级和一级试验

This practice permits an analyst to compare the general performance of a laboratory instrument on any given day with the prior performance of that instrument. This practice is not intended for comparison of different instruments with each other, nor is it directly applicable to dedicated process FT-NIR analyzers. This practice requires the use of a check sample compatible with the instrument under test as described in 5.3.1.1 This practice covers two levels of tests to measure the performance of laboratory Fourier transform near infrared (FT-NIR) spectrometers. This practice applies to the short-wave near infrared region, approximately 800 nm (12 500 cm -1) to 1100 nm (9090.91 cm -1); and the long-wavelength near infrared region, approximately 1100 nm (9090.91 cm -1) to 2500 nm (4000 cm -1). This practice is intended mainly for transmittance measurements of gases and liquids, although it is broadly applicable for reflectance measurements. 1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests

ASTM E1982-98(2007) 利用长光程傅里叶变换红外光谱仪(OP/FT-IR)监测空气中的气体和蒸气的标准规程

An OP/FT-IR monitor can, in principle, measure the concentrations of all IR-active gases and vapors in the atmosphere. Detailed descriptions of OP/FT-IR systems and the fundamental aspects of their operation are given in Guide E 1865 and the FT-IR Open-Path Monitoring Guidance Document. A method for processing OP/FT-IR data to obtain the concentrations of gases over a long, open path is given in Compendium Method TO-16. Applications of OP/FT-IR systems include monitoring for gases and vapors in ambient air, along the perimeter of an industrial facility, at hazardous waste sites and landfills, in response to accidental chemical spills or releases, and in workplace environments.1.1 This practice covers procedures for using active open-path Fourier transform infrared (OP/FT-IR) monitors to measure the concentrations of gases and vapors in air. Procedures for choosing the instrumental parameters, initially operating the instrument, addressing logistical concerns, making ancillary measurements, selecting the monitoring path, acquiring data, analyzing the data, and performing quality control on the data are given. Because the logistics and data quality objectives of each OP/FT-IR monitoring program will be unique, standardized procedures for measuring the concentrations of specific gases are not explicitly set forth in this practice. Instead, general procedures that are applicable to all IR-active gases and vapors are described. These procedures can be used to develop standard operating procedures for specific OP/FT-IR monitoring applications. 1.2 This practice does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this practice to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air

ASTM E1865-97(2007) 空气中气体和蒸汽的开路傅里叶变换红外监测的标准实施规程

This guide is intended for users of OP/FT-IR monitors. Applications of OP/FT-IR systems include monitoring for hazardous air pollutants in ambient air, along the perimeter of an industrial facility, at hazardous waste sites and landfills, in response to accidental chemical spills or releases, and in workplace environments.1.1This guide covers active open-path Fourier transform infrared (OP/FT-IR) monitors and provides guidelines for using active OP/FT-IR monitors to obtain concentrations of gases and vapors in air. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air