共找到 55 条与 力与变形测试仪器 相关的标准,共 4 页
Metallic materials-Calibration of extensometers systems used in uniaxial testing
Metallic materials—Calibration of force-proving instruments used for the verification of uniaxial testing machines
本标准规定了力标准机的术语和定义、技术要求、检验与校准方法、检验规则、标志与包装和随行技术文件。 本标准适用于静重式、杠杆式、液压式和叠加式力标准机。
Verification and calibration of force standard machines
本标准规定了力传感器的技术要求及检验方法。 本标准适用于应变式力传感器(以下简称力传感器)的检验。其他形式的力传感器也可参照使用。
Verification of force transducers
本标准规定了单轴试验机[例如拉力和(或)压力试验机]静态检验用标准测力仪的校准,并给出标准测力仪的分级方法。 本标准一般适用于由测量受力体的弹性变形或与之成正比的量来确定其所受力的标准测力仪。
Calibration of force-proving instruments used for the verification of uniaxial testing machines
本标准规定了单轴试验用引伸计的静态标定方法。术语“引伸计”的含义是指位移测量装置并包括指示或记录该位移的系统。注:本标准目前未提供对下列型式引伸计标定的详细指导: ——变标距式; ——非接触试样式; ——平面应变测量式。 对于这些型式引伸计的标定宜专门考虑。
Calibration of extensometers used in uniaxial testing (ISO 9513:1999,Metallic materials--Calibration of extensometers used in uniaxial testing, IDT)
本标准规定了单轴试验机(例如:拉力/压力试验机)静态检验用测力仪的校准,并给出测力仪的分级方法。测力仪被定义为从力传感器直到包括指示装置在内的整个组合。本标准一般适用于其所受的力是通过测量受力体的弹性变形或与之成正比的量来确定的测力仪。
Calibration of force-proving instruments used for the verification of testing machines
General technical conditions for torque standard machines
Tension/compression testing machines -- Calibration and verification of the force-measuring system
Non-contact extensometer system
Static testing machine controller
本标准规定了标准扭矩仪的符号、单位与说明、技术要求、检验方法、检验规则、标志与包装。 本标准适用于扭转试验机检验用标准扭矩仪(以下简称扭矩仪)的检验。
Standard torque meters.Technical specification
本标准规定了中功率计的要求、试验方法、质量检验规则、包装、标志、运输和贮存。本标准适用于测量频率高于10 MHz,功率为0. 1 W至500 W范围内微波连续波功率的中功率计。
General specification of medium power meter
Metallic materials - Calibration of extensometer systems used in uniaxial testing (ISO 9513:2012 + Cor. 1:2013); German version EN ISO 9513:2012
This Standard specifies a method for the calibration of force-proving instruments used for the static verification of uniaxial testing machines (e.g. tension/compression testing machines) and describes a procedure for the classification of these instruments. This Standard is applicable to force-proving instruments in which the force is determined by measuring the elastic deformation of a loaded member or a quantity which is proportional to it.
Calibration of force-proving instruments used for the verification of uniaxial testing machines
This SAE Recommended Practice defines an Inertia Dynamometer Test procedure that assesses the effectiveness behavior of a friction material with regard to pressure, temperature and speed for motor vehicles fitted with hydraulic brake actuation. The main purpose of SAE J 2522 is to compare friction materials under the most equal conditions possible. To account for the cooling behavior of different test stands, the fade sections are temperature-controlled.
Dynamometer Global Brake Effectiveness
Calibration method of anchor cable dynamometer
本标准规定了钢弦式锚索测力计的基本参数、技术要求、试验方法、检验规则和标志、包装、运输、贮存的要求。本标准适用于岩土工程及其他构筑物安全监测中用于预应力锚索等张力变化监测的钢弦式锚索测力计(简称测力计)。
Vibrating wire load cell
本规程适用于百分表式和应变式等标准扭矩仪(以下简称扭矩仪)的首次检定、后续检定和使用中检查。
Verification Regulation of Standard Torque-meters
Metallic materials - Calibration of force-proving instruments used for the verification of uniaxial testing machines
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号