P04 基础标准与通用方法 标准查询与下载

ISO 23469:2005 建筑设计基础.对设计土工技术作业的地震作用

This International Standard provides guidelines for specifying seismic actions for designing geotechnical works, including buried structures (e.g. buried tunnels, box culverts, pipelines and underground storage facilities), foundations (e.g. shallow and deep foundations, and underground diaphragm walls), retaining walls (e.g. soil retaining and quay walls), pile-supported wharves and piers, earth structures (e.g. earth and rockfill dams and embankments), gravity dams, landfill and waste sites. NOTE The guidelines provided in this International Standard are general enough to be applicable for both new and existing geotechnical works. However, for use in practice, procedures more specific to existing geotechnical works can be needed, such as those described for existing structures in ISO 13822.

Bases for design of structures - Seismic actions for designing geotechnical works

BS EN 13375:2004 临时边缘保护设备.产品规范、试验方法

This European Standard is one of a series of standards applicable to flexible sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles. This document specifies: — the composition, the characteristics and the preparation procedure of the base specimen concrete slabs; — the composition, the characteristics and the preparation procedure of different bituminous mixtures for the asphalt layer; — the rules for the preparation of specimens.

Flexible sheets for waterproofing-Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles-Specimen preparation

BS EN ISO 9046:2005 建筑施工.连接产品.恒温下密封剂的粘附/粘结性能的测定

This International Standard specifies a method for the determination of the adhesion/cohesion properties of sealants with predominantly plastic behaviour which are used in joints in building construction.

Building construction - Jointing products - Determination of adhesion/cohesion properties of sealants at constant temperature

DIN EN 14505:2005 复合结构物的阴极防护

This European standard is applicable to structures, which are to be cathodically protected, but cannot be electrically isolated, whether for technical or safety reasons," from foreign metallic structures situated in the same electrolyte as the structure to be protected. Such a structure is referred to as a ""complex structure"". This European Standard is not applicable to structures that can be protected in accordance with EN 12954. It is assumed in this European Standard that the design", installation, commissioning, inspection and maintenance is entrusted to adequately trained, experienced, competent and reliable personnel in order to achieve effective and efficient cathodic protection.#,,#

Cathodic protection of complex structures; German version EN 14505:2005

BS EN 14505:2005 复杂构造的阴极保护

This European Standard applies to the cathodic protection of complex structures. It is applicable to structures, which are to be cathodically protected, but cannot be electrically isolated, whether for technical or safety reasons, from foreign metallic structures situated in the same electrolyte as the structure to be protected. Such a structure is referred to as a "complex structure". This European Standard is not applicable to structures that can be protected in accordance with EN 12954. When contacts with foreign structures or defective isolation from foreign structures exist, but can be corrected, EN 12954 is applicable instead of this document. As an example pipeline network distribution systems are not considered to be complex structures It is assumed in this document that the design, installation, commissioning, inspection and maintenance are entrusted to adequately trained, experienced, competent and reliable personnel in order to achieve effective and efficient cathodic protection. Annexes A and B show the principle scheme of a complex structure with examples.

Cathodic protection of complex structures

DIN-Fachbericht 142:2005 定向系统.露天建筑物定向系统的要求

This recommendation contains requirements on orientation systems in open buildings. It gives a basis for new buildings and reconstruction of existing buildings. Orientation systems in open buildings are to be designed in such a way that people which are restricted in their mobility are able to find their way without any other help as far as possible. Due to the versatility of handicaps concepts and minimum requirements should be established to reach a large amount of users.

Orientation systems - Requirements on orientation systems in open buildings

BS EN 1991-1-4:2005+A1:2010 欧洲法规 1.对建筑物的作用.一般作用.风作用

Eurocode 1. Actions on structures. General actions. Wind actions

BS EN 1991-1-4:2005 欧洲法规 1.对建筑物的作用.一般作用.风作用

1) EN 1991-1-4 gives guidance on the determination of natural wind actions for the structural design of building and civil engineering works for each of the loaded areas under consideration. This includes the whole structure or parts of the structure or elements attached to the structure, e. g. components, cladding units and their fixings, safety and noise barriers. This Part is applicable to: (3) This part is intended to predict characteristic wind actions on land-based structures, their components and appendages. (4) Certain aspects necessary to determine wind actions on a structure are dependent on the location and on the availability and quality of meteorological data, the type of terrain, etc. These need to be provided in the National Annex and Annex A, through National choice by notes in the text as indicated. Default values and methods are given in the main text, where the National Annex does not provide information. (5) Annex A gives illustrations of the terrain categories and provides rules for the effects of orography including displacement height, roughness change, influence of landscape and influence of neighbouring structures. (6) Annex B and C give alternative procedures for calculating the structural factor cscd. (7) Annex D gives cscd factors for different types of structures. (8) Annex E gives rules for vortex induced response and some guidance on other aeroelastic effects. (9) Annex F gives dynamic characteristics of structures with linear behaviour (10) This part does not give guidance on local thermal effects on the characteristic wind, e.g. strong arctic thermal surface inversion or funnelling or tornadoes. ? Buildings and civil engineering works with heights up to 200 m, see also (11). ? Bridges having no span greater than 200 m, provided that they satisfy the criteria for dynamic response, see (12) and 8.2. (11) Guyed masts and lattice towers are treated in EN 1993-3-1 and lighting columns in EN 40. (12) This part does not give guidance on the following aspects: ? torsional vibrations, e.g. tall buildings with a central core ? bridge deck vibrations from transverse wind turbulence ? wind actions on cable supported bridges ? vibrations where more than the fundamental mode needs to be considered. BS EN 1991-1-4-2005 EN 1991-1-4-2005 (E)

Eurocode 1: Actions on structures. Part 1-4: General actions .Wind actions

DIN 277-3:2005 建筑物的面积和体积.第3部分:数量和相关单位

The document defines quantity and reference units for building cost elements according to DIN 276.

Areas and volumes of building - Part 3: Quantities and reference units

SANS 10111-2-4:2005 几何产品（GPS）技术规范．几何公差．位置公差

Describes positional tolerancing. This tolerancing method is applied to the location of a point, of a line nominally straight and of a surface nominally plane, e.g. the centre of a sphere, the axis of a hole or shaft and the median surface of a slot.

Geometrical Product Specifications (GPS) - Geometrical tolerancing - Positional tolerancing

PP 8888-1-2005 绘图规程:学校和学院使用BS 8888-2000:技术产品规范的指南

Drawing practice: a guide for schools and colleges to BS 8888:2004: Technical product specification

NF P01-020-1:2005 建筑物.建筑产品和建筑物的环保质量.建筑物环保和卫生性能的描述框架

Building - Environmental quality of construction products and buildings - Part 1 : framework for the description of environmental and sanitary performances of buildings.

DIN 277-2:2005 建筑物的面积和体积.第2部分:纯地面面积的分类(使用面积、技术操作面积和环行面积)

Areas and volumes of buildings - Part 2: Classification of net ground areas (utilization areas, technical operating areas and circulation areas)

DIN 277-1:2005 建筑物的面积和体积.第1部分:术语和计算基础

This standard specifies rules for the calculation of areas and volumes of buildings. Areas and volumes serve for the ascertainment of construction costa as well as rent and purchase prices. Furthermore they are used to compare the efficiency and economy of different buildings. Uniform rules for the calculation of areas and volumes are therefore a prerequisite for the comparability of costs, prices and performance of buildings.#,,#

Areas and volumes of buildings - Part 1: Terminology, bases of calculation

JGJ 146-2004 建筑施工现场环境与卫生标准

Standard of environment and sanitation of construction site

JGJ 147-2004 建筑拆除工程安全技术规范

Technical code for safety of demolishing and removing of buildings

ASCE 5-99/6-99-2005 圬工结构建筑码要求.ACI 530-05/TMS 402-05

Building Code Requirements for Masonry Structures ACI 530-05/TMS 402-05

Building Code Requirements for Masonry Structures ACI 530-05/TMS 402-05

ASCE 7-05-2005 建筑和其它包括修补1的最低负载

Guidelines for the Provision of General Structural Integrity. Generally, connections between structural components should he ductile and have a capacity for relatively large deformations and energy absorption under the effect of abnormal conditions. This criterion is met in many different ways, depending on the structural system used. Details that are appropriate for resistance to moderate wind loads and seismic loads often provide sufficient ductility. In 1999, ASCE issued a state of practice report that is a good introduction to the complex field of blast resistant design [Ref. CI-1 11

Minimum Design Loads for Buildings and Other Structures Including Supplement 1

ASCE 6-2005 圬工结构规范.ACI 530.1-05/TMS 602.05

Specification for Masonry Structures ACI 530.1-05/TMS 602.05

Specification for Masonry Structures ACI 530.1-05/TMS 602.05

DIN EN ISO 3766 Berichtigung 1:2005 对DIN EN ISO 3766-2004的勘误

This standard contains corrections to DIN EN ISO 3766:2004-05.

Corrigenda to DIN EN ISO 3766:2004-05; German version EN ISO 3766:2003/AC:2004