P15 工程抗震 标准查询与下载

CECS 126-2001（条文说明） 叠层橡胶支座隔震技术规程

Technical specification for seismic-isolation with laminated rubber bearing isolators

DB/T 1-2000 地震行业标准体系表

本标准规定了地震行业标准化范围内的标准体系结构、标准组成，以及标准之间的内在联系，适用于编制地震标准制订、修订规划和计划，也适用于有关人员查阅地震标准信息。在编制具体标准制订年度计划时，标准明细表中标明“待制定”字样的标准名称容许变更。

Table of Standard System for Seismic Industry

DB/T 14-2000 原地应力测量水压致裂法和套芯解除法技术规范

本标准规定了用水压致裂法和套芯解除法测量原地应力的技术方法和技术要求，适用于各类岩体工程需要原地应力资料场点的测量，水压致裂法适用于测量深度大于50 m的情况，套芯解除法适用于需要获知三维主应力大小和方向的情况。

Code of hydraulic fracturing and overcoring method for in-situ stress measurement

DL 5073-2000 水工建筑物抗震设计规范

Specifications for seismic design of hydraulic structures

DB/T 11.1-2000 地震数据分类与代码 第一部分：基本类别

本部分规定了地震数据的分类与编码方法以及地震数据基本类别的分类与代码，适用于我国防震减灾工作及相关科学研究中对地震数据的汇集、管理、处理、交换和应用。

Categories and codes for earthquake - related data Part 1:Basic categories

DB/T 12.1-2000 地震数据分类与代码 第一部分：基本类别

本标准规定了地震前兆观测传感器的接口和控制命令。地震前兆观测传感器接口适用于地震前兆观测传感器、地震前兆数据采集器和计数器（频率计）。地震前兆观测传感器控制命令适用于智能化的地震前兆观测传感器和传感器与二次仪表一体化设计的地震前兆观测仪器。

Earthquake precursor observation instrument Part 1:Interface and control of sensor

JG 118-2000 建筑隔震橡胶支座

本标准规定了建筑隔震橡胶支座的产品定义、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于工业与民用建筑所用的建筑隔震橡胶支座。对构筑物、桥梁、铁路、设备等隔震减震所需的隔震橡胶支座也可参照使用。

Rubber isolation bearings for buildings

ASCE 4-2000 核心结构相关的地震安全分析

This standard is intended for use in the seismic analysis of all safety-related structures of nuclear facilities including, but not limited to, above and below ground structures, buried piping, above ground vertical tanks and structures with seismic isolation systems. Analysis of caisson and pile-supported foundations, unlined tunnels, and floating structures are not covered by this standard, However, nothing in this standard should be considered to preclude the use of these structures and structural elements.

Seismic Analysis of Safety-Related Nuclear Structures and Commentary

HG/T 20665-1999 化工建、构筑物抗震设防分类标准

1.0.1为使化工企业建、构筑物的抗震设计有明确的设防类别，以减轻地震灾害，合理使用建设资金，特制定本标准。 1.0.2本标准是根据国家标准《建筑抗震设防分类标准》(GB 50223-95)的原则，结合化工行业的特点而制定的化工企业生产装置建、构筑物的抗震设防分类标准。 1.0.3本标准适用于抗震设防烈度为6～9度地区的化工生产、运输、储存的单体建、构筑物抗震设防类别划分。 1.0.4建设地区的抗震设防烈度或设计地震动参数，应按国家有关部门的规定确定。 1.0.5执行本标准时，尚应符合国家现行有关标准规范的要求。

Standard for classification of seismic protection of buildings and structures in chemical industry

BS DD ENV 1998-4:1999 欧洲规程8:防地震结构的设计条例.贮仓、水箱和管道

Eurocode 8: Design provisions for earthquake resistance of structures. Silos, tanks and pipelines

JGJ/T 13-1994 设置钢筋混凝土构造柱多层砖房抗震技术规程

Aseismic technical specification for multi-storey masonry building with reinforced concrete tie column

SY/T 0318-1998 石油浮放设备隔震技术标准

本标准适用于设防烈度为6-9度地区浮放设备的隔震设计及安装，9度以上地区的浮放设备的隔震应作专门研究。

Standard for unfixed equipment isolation technique used in petroleum industry

ASCE 25-99-1999 地震开动机械气体关闭设备

This Standard provides minimum functionality requirements for earthquake-actuated automatic gas shutoff devices and systems (hereafter referred to as devices) meant to include mechanical devices consisting of a sensing means and a means to shut off the flow of gas.

Earthquake-Actuated Automatic Gas Shutoff Devices

ASTM E2026-99 估测地震中建筑物损伤性的标准指南

1.1 Purpose-This guide defines and establishes good commercial, customary practice, and standard-of-care in the United States for conducting a probabilistic study of expected loss to buildings from damage associated with earthquakes and for the preparation of a narrative report containing the results of the study. As such, this guide permits a user to satisfy, in part, their real estate transactional due-diligence requirements with respect to assessing a property''s potential for building losses associated with earthquakes. 1.1.1 Recognized Earthquake Hazards-Hazards addressed in this guide include earthquake ground shaking, earthquake caused sit instability, including faulting, land sliding, and densification, and earthquake caused tsunamis and seiches. Earthquake caused fires and toxic materials releases are not considered. 1.1.2 Other Federal, State, and Local Laws and Regulations-This guide does not address requirements of any federal, state, or local laws and regulations of building construction or maintenance. Users are cautioned that current federal, state, and local laws and regulations may differ from those in effect at the time of the original construction of the building(s). 1.2 Objectives-The objectives for this guide are as follows: 1.2.1 To synthesize and document good commercial, customary practices for the estimation of probable loss to buildings from earthquakes for real estate improvements; 1.2.2 To facilitate standardized estimation of probable losses to buildings from earthquakes; 1.2.3 To ensure that the standard of site observations, document review and research is appropriate, practical, sufficient, and reasonable for such an estimation; 1.2.4 To establish what reasonably can be expected of and delivered by a loss estimator in conducting an estimation of probable loss to buildings from earthquakes; 1.2.5 To establish an industry standard for appropriate observations and analysis in an effort to guide legal interpretation of the standard of care to be exercised for the conducting of an estimation of probable loss to buildings from earthquakes; and, 1.2.6 To establish the requirement that a loss estimator communicates observations, opinions, and conclusions in a manner meaningful to the user and not misleading either by content or by omission. 1.3 Considerations beyond this scope-The use of this guide is limited strictly to the scope set forth herein. Section 3 of this guide identifies, for information purposes, certain conditions that may exist on a property that are beyond the scope of this guide but may warrant consideration by the parties to a real estate transaction. 1.4 Organization of this guide-This guide has several parts (see Table of Contents). 1.5 Limitations-This guide does not purport to provide for the preservation of life safety, or prevention of building damage associated with its use, or both. It is the responsibility of the user of this guide to establish appropriate life safety and damage prevention practices and determine the applicability of current regulatory limitations prior to use. 1.6 Commentary-See Appendix X1 for commentary on Section 1.

Standard Guide for the Estimation of Building Damageability in Earthquakes

JGJ 116-1998 建筑抗震加固技术规程

Technical specification for seismic strengthening of buildings

GY 5060-1997 广播电影电视建筑抗震设防分类标准

Specifications for classifications of anti-seismic capabilities of broadcasting, film, and television buildings

BS DD ENV 1998-3:1997 欧洲法规8:建筑物抗地震的设计条例.塔楼、天线杆和烟囱

Eurocode 8: Design provisions for earthquake resistance of structures. Towers, masts and chimneys

ASTM E1007-97 通过天棚地板组件及其支承结构传导的夯击机械撞击声的现场测量方法

1.1 This test method covers the measurement of the transmission of impact sound generated by a standard tapping machine through floor-ceiling assemblies and associated supporting structures in field situations. 1.2 Measurements may be conducted on all types of floor-ceiling assemblies, including those with floating-floor or suspended ceiling elements, or both, and floor-ceiling assemblies surfaced with any type of floor-surfacing or floor-covering materials. 1.3 This test method further prescribes: 1.3.1 A uniform procedure for reporting test data, that is, the normalized one-third octave band sound pressure levels generated in the receiving room by the operation of the standard tapping machine on the floor-ceiling assembly. 1.3.2 The use of a single-figure classification rating, "Field Impact Insulation Class, FIIC" that can be used by architects, builders, and specification and code authorities for acoustical evaluation purposes in completed buildings. The FIIC is obtained by matching a standard reference contour to the plotted normalized one-third octave band sound pressure levels at each test frequency obtained in accordance with 8.2. For details regarding the derivation and significance of the FIIC, see Classification E989. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures

JGJ 101-1996 建筑抗震试验方法规程

Specification of test methods for earthquake resistant building

JGJ/T 97-1995 工程抗震术语标准

Standard for terms of earthquake resistant engineering