P24 砌体结构工程 标准查询与下载
共找到 362 条与 砌体结构工程 相关的标准，共 25 页
本规程适用于山东省行政区域内抗震设防烈度8度及 8度以下地区，以蒸压灰砂砖为墙体材料的砌体结构的设计、施工及施工质量验收。
Technical specification for autoclaved lime-sand brick masonry
- ICS
- 91.080.30
- CCS
- P24
- 发布
- 2017-03-20
- 实施
- 2017-04-01
本规程适用于砌体结构中砌筑砂浆抗压强度的现场检测。 本规程不适用于遭受高温、冻害、化学侵蚀、火灾等表面损伤砂浆的检测，以及冻结法施工砂浆在强度回升期的检测。
Technical specification for testing compressive strength of masonry mortar by penetration resistance method
- ICS
- CCS
- P24
- 发布
- 2017-02-20
- 实施
- 2017-09-01
Special mortar for dry construction of autoclaved aerated concrete
- ICS
- 91.100.10
- CCS
- P24
- 发布
- 2017-02-15
- 实施
- 2017-04-01
Application of building products in structures - Part 401: Rules for the application of clay masonry units according to DIN EN 771-1:2015-11
- ICS
- 91.080.30;91.100.25
- CCS
- P24
- 发布
- 2017-01
- 实施
Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brackets; German version EN 845-1:2013+A1:2016
- ICS
- 91.080.30
- CCS
- P24
- 发布
- 2016-12
- 实施
Specification for ancillary components for masonry - Part 3: Bed joint reinforcement of steel meshwork; German version EN 845-3:2013+A1:2016
- ICS
- 91.080.30
- CCS
- P24
- 发布
- 2016-12
- 实施
Specification for ancillary components for masonry - Part 2: Lintels; German version EN 845-2:2013+A1:2016
- ICS
- 91.080.30
- CCS
- P24
- 发布
- 2016-12
- 实施
This European Standard is applicable to factory-made rendering/plastering mortars based on inorganic binders for external (rendering) and internal (plastering) use on walls, ceilings, columns and partitions. It contains definitions and final performance requirements. This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard. The marking requirement for products covered by this European Standard is included. It does not cover mortars where calcium sulphate binder is the principal active binding agent. Calcium sulphate binder can be used as an additional binder together with air lime. If air lime is the principal active binding component, the rendering/plastering mortar is covered by this European Standard. If the calcium sulphate binder is the principal active binding component, the mortar is covered by EN 13279. Special fire resistant- and acoustical mortars, mortars for structural repair and surface treatments of building elements such as materials for smoothing or trueing, paints, coatings, thin-layer organic renders/plasters and prefabricated units (e. g. plasterboards) are not dealt with in this European Standard. This European Standard covers rendering/plastering mortars defined in Clause 3 with the exception of site-made rendering/plastering mortars. However, this European Standard or part of this European Standard may be used in conjunction with codes of application and national specifications covering site-made mortar.
Specification for mortar for masonry - Part 1: Rendering and plastering mortar
- ICS
- 91.100.10
- CCS
- P24
- 发布
- 2016-11
- 实施
This European Standard specifies requirements for factory-made masonry mortars (bedding, jointing and pointing) for use in masonry walls, columns and partitions (e. g. facing and rendered masonry, load bearing or non-load bearing masonry structures for buildings and civil engineering works). This European Standard defines for fresh mortar the performance related to workable life, chloride content, air content, density and correction time (for thin-layer mortar only). For hardened mortar it defines, e. g. performance related to compressive strength, bond strength, density measured according to the corresponding test methods contained in separate European Standards. This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard. The marking requirement for products covered by this European Standard is included. This European Standard covers masonry mortars defined in Clause 3 with the exception of site made mortar. However, this European Standard or part of this European Standard may be used in conjunction with codes of application and national specifications covering site made mortar.
Specification for mortar for masonry - Part 2: Masonry mortar
- ICS
- 91.100.10
- CCS
- P24
- 发布
- 2016-11
- 实施
Methods of test for masonry - Part 2: Determination of flexural strength; German version EN 1052-2:2016
- ICS
- 91.080.30
- CCS
- P24
- 发布
- 2016-08
- 实施
Methods of test for masonry units - Part 5: Determination of the active soluble salts content of clay masonry units; German version EN 772-5:2016
- ICS
- 91.100.25
- CCS
- P24
- 发布
- 2016-08
- 实施
Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels; German version EN 846-9:2016
- ICS
- 91.080.30
- CCS
- P24
- 发布
- 2016-08
- 实施
Building works - Small masonry partition walls - Part 3 : memento - Amendment 1
- ICS
- 91.060.10;91.080.30
- CCS
- P24
- 发布
- 2016-07-15
- 实施
- 2016-07-15
Building works - Small masonry partition walls - Part 1-1 : contract bill of technical model clauses - Amendment 1
- ICS
- 91.060.10;91.080.30
- CCS
- P24
- 发布
- 2016-07-15
- 实施
- 2016-07-15
Methods of test for mortar for masonry. Determination of adhesive strength of hardened rendering and plastering mortars on substrates
- ICS
- 91.080.30;91.100.10
- CCS
- P24
- 发布
- 2016-06-30
- 实施
- 2016-06-30
This European Standard specifies a method for the determination of the adhesive strength between rendering and plastering mortars and a substrate.
Methods of test for mortar for masonry - Part 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates
- ICS
- 91.100.10
- CCS
- P24
- 发布
- 2016-06
- 实施
Methods of test for masonry units. Determination of the active soluble salts content of clay masonry units
- ICS
- 91.080.30;91.100.15
- CCS
- P24
- 发布
- 2016-03-31
- 实施
- 2016-03-31
Methods of test for ancillary components for masonry. Determination of flexural resistance and shear resistance of lintels
- ICS
- 91.060.10;91.080.30
- CCS
- P24
- 发布
- 2016-03-31
- 实施
- 2016-03-31
This European Standard specifies methods for determining the flexural and shear resistances and load deflection characteristics of single span, single or composite lintels used for supporting uniformly distributed loads over openings in masonry construction.
Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels
- ICS
- 91.060.10;91.080.30
- CCS
- P24
- 发布
- 2016-03
- 实施
This European Standard specifies a method for determining the active soluble salts content of clay masonry units.
Methods of test for masonry units - Part 5: Determination of the active soluble salts content of clay masonry units
- ICS
- 91.100.25
- CCS
- P24
- 发布
- 2016-03
- 实施
