P30 工业与民用建筑工程综合 标准查询与下载

BOCA CHAPTER 6 NBC-1996 各类建设

The BOCA National Mechanical Code was initially prepared and updated on the premise that adequate code requirements are essential to the safe installation and maintenance of all mechanical equipment and systems in order to protect the public health, sa

Types of Construction

BOCA NBC COMM96 V1 CH 6-1996 各类建设

Types of Construction

Types of Construction

BOCA NBC COMM96 V2 CH 32-1996 公众通行权的建设

Construction in the Public Right-of-Way

Construction in the Public Right-of-Way

BOCA NBC COMM96 V2 CH 33-1996 拆迁和施工的现场工作,

Site Work, Demolition and Constuction

Site Work, Demolition and Constuction

ASTM E1155M-96(2008) 测定地坪平面度(FF)和地坪水平度(FL)的试验方法(米制)

This test method provides statistical (and graphical) information concerning floor surface profiles. Results of this test method are used primarily to: Establish compliance of randomly trafficked floor surfaces with specified FF Flatness and FL Levelness tolerances, Evaluate the effect of different construction methods on resulting floor surface flatness and levelness, and Investigate the curling and deflection of floor surfaces. Results of this test method shall not be used to enforce contract flatness and levelness tolerances on those floor installations primarily intended to support the operation of fixed-path vehicle systems (for example, narrow aisle warehouse floors). Note 28212;When the traffic patterns across a floor are random, (as is generally the case) evaluation of the floor''s FF Flatness and FL Levelness will necessarily involve a random sampling of the surface, since all of the infinite potential profiles to be seen by the traffic can not possibly be measured. In those instances when the traffic across a floor will be confined to specific paths, however, the requirement for random sampling is eliminated, since the floor can indeed be inspected exactly as it will be seen by all of the traffic. In these special cases, rather than inferring the condition of the traffic paths from a random sample, it is far more useful to measure each of the traffic paths directly using continuous recording floor profilometer configured to run exactly in the traffic wheel paths. Such direct simulation measurements eliminate the inherent uncertainties of statistical sampling and provide profile information immediately applicable to the correction of the surface in way of the future traffic.1.1 This test method covers a quantitative method of measuring floor surface profiles to obtain estimates of the floor''s characteristic FF Flatness and FL Levelness Face Floor Profile Numbers (F-Numbers) using the metric (SI) system of units. Note 18212;This is the metric companion to Test Method E 1155. 1.2 The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining F_F Floor Flatness and F_L Floor Levelness Numbers [Metric]

ASTM E1155M-96(2001) 使用F-数字制测定楼板平正度和水平度的试验方法(米制)

1.1 This test method covers a quantitative method of measuring floor surface profiles to obtain estimates of the floor''s characteristic FF Flatness and FL Levelness Face Floor Profile Numbers (F-Numbers) using the metric (SI) system of units. Note 1--This is the metric companion to Test Method E 1155.1.2 The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining F_F Floor Flatness and F_L Floor Levelness Numbers [Metric]

ASTM D4756-96 硬质聚氯乙烯挡板和拱腹安装的标准实施规程

1.1 This practice covers the minimum requirements for and the methods of installation of rigid vinyl siding, soffits, and accessories on the exterior wall and soffit areas of buildings. In all applications, refer also to the specific manufacturer''s instructions for installation. 1.2 This practice covers aspects of installation relating to effectiveness and durability in service. 1.3 The various application systems are located in the following sections of this practice: Section 8 Substrate, Surface Preparation Section 9 Application of Horizontal Siding Section 10 Application of Vertical Siding Section 11 Application of Soffits Section 12 Special Details 1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. Note 1-There are no ISO standards covering the subject matter of this practice. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit

ISO 4463-2:1995 建筑物的测量方法 定线和测量 第2部分:测站和目标

Deals with the stages of establishing and marking measuring stations and targets on building sites. Examples of different stations, targets and location plans are given in annex A. This first edition together with ISO 4463-1 and ISO 4463-3 replaces ISO 4463:1979, which has been technically revised.

Measurement methods for building - Setting-out and measurement - Part 2: Measuring stations and targets

ISO 4463-3:1995 建筑物的测量方法 定线和测量 第3部分:观测和测量作业所获资料的检查目录

Provides guidance in the form of check-lists for the surveying and setting-out services that may be required during the development and construction of buildings and ancillary works. This first edition together with ISO 4463-1 and ISO 4463-2 replaces ISO 4463:1979, which has been technically revised.

Measurement methods for building - Setting-out and measurement - Part 3: Check-lists for the procurement of surveys and measurement services

ANSI A10.16-1995 建筑施工和拆除工作.隧道、竖井和藻井的安全要求

Establishes safety requirements pertaining to the construction of tunnels, shafts, and caissons. The requirements set forth in this standard cover environmental control; related facilities; fire prevention; hoisting; haulage; and electrical, drilling and

Construction and Demolition Operations - Safety Requirements for Tunnels, Shafts, and Caissons

ASTM E1679-95(2005) 建筑物或建筑物有关设备适用性装配要求的标准实施规程

1.1 This practice is a definitive procedure for setting requirements for the serviceability of a building or building-related facility.1.2 This practice is not intended to be used for regulatory purposes.1.3 This practice can be used for setting the profile of serviceability requirements of an occupant group in an existing building or building-related facility or of a group planning to move and looking at new accommodations to rent, buy, or build.1.4 This practice can be used for setting the profile of serviceability requirements of an owner, facility manager, lender, or other investor.1.5 The process of creating or adapting a set of classifications for establishing the levels of serviceability required by an occupant group or organization is outside the scope of the practice.1.6 This practice contains the following information, in the sections indicated:

Standard Practice for Setting the Requirements for the Serviceability of a Building or Building-Related Facility

ANSI A10.15-1995 建筑施工和拆除工作.挖泥作业的安全要求

Applies to the operation, inspection, and maintenance of any vessel fitted with machinery for the purpose of removing or relocating of material from or in a body of water.

Safety Requirements for Dredging

ISO 9699:1994 建筑物的性能标准 简要检验项目 建筑设计的简要内容

Describes the content of a brief for building design. Can be used from the time when the client first considers the possible need for a building project. Applies to all kinds and sizes of design project. Can also apply whatever the chosen function or purpose of the brief, for example instructing, promoting discussion, recording, as a basis for evaluation or in a formal competition to select consultants.

Performance standards in building - Checklist for briefing - Contents of brief for building design

ISO/TR 9527:1994 房屋建筑 建筑物中残疾人的需要 设计指南

Deals with the problems of the handicapped in buildings, as far as they present practical challenges to designers and architects. Provides some guidance for planners and for the formulation of local regulation, standards, recommendations etc. not in the form of a standard but in the form of a general account of basic and particular needs.

Building construction - Needs of disabled people in buidlings - Design guidelines

DIN V 11535-2:1994 温室.1280米宽纵向网格尺寸3065米长的钢和铝结构

The width of 12,80 m adapt the international used dimensions.#,,#

Greenhouses; steel and aluminium construction 12,80 m in width with a longitudinal grid dimension of 3,065 m

JBJ/T 1-1994 机械工厂办公与生活建筑设计标准

Design standard of office and living building for machinery factory

CSA S413-94-CAN/CSA-1994 停留构筑物.第2版.通用指令第1-2号

The Canadian Standards Association (CSA), under whose auspices this National Standard has been produced, was chartered in 7979 and accredited by the Standards Council of Canada to the National Standards system in 7973. It is a not-for-profit, nonstatu

Ouvrages De Stationnement Deuxieme Edition; Fiche No 1-2

ISO 6707-2:1993 建筑和土木工程 词汇 第2部分:合同术语 两种语言版

Defines 179 terms in English and French arranged in alphabetical order in English within the following eight categories: general concepts, project information, design phase, contracts, financial, construction, post-construction maintenance, persons involved.

Buildings and civil engineering; vocabulary; part 2: contract terms

ISO 9882:1993 建筑物的性能标准 预制混凝土楼板的性能试验在非集中荷载下的工况

Defines test procedures for determining the mechanical performance of precast concrete floors made of a single piece, or made up of precast joists (reinforced concrete or precast concrete) completed with filler blocks and concrete poured in situ. The parameters measured are: the maximum load, which does not result in collapse, the instantaneous and deferred deformations under imposed load, and the maximum load which the floor or its constituent precast element can support without collapse during its construction. Applies to floors designed to support loads of less than 5000 N m and having spans of less than 12 m.

Performance standards in building; performance test for precast concrete floors; behaviour under non-concentrated load

ISO 9883:1993 建筑物的性能标准 预制混凝土楼板的性能试验 在集中荷载下的工况

The test procedures defined are: transverse dynamic bond test on finished floors, penetration resistance test of the finished floor, and indentation/bending test on filler blocks (this test is designed to verify safety at the assembly stage). Applies to all kinds of precast concrete floors and to components thereof.

Performance standards in building; performance test for precast concrete floors; behaviour under concentrated load