P42 建筑给水、排水工程 标准查询与下载

BS DD CEN ISO/TS 15874-7:2003 冷热水装置用塑料管道系统.聚丙烯(PP).合格评定指南

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Guidance for the assessment of conformity

CJ/T 232-2006 薄壁不锈钢内插卡压式管材及管件

本标准规定了薄壁不锈钢内插卡压式管材(以下简称钢管)及管件的要求、试验方法、检验规则、标志、包装、贮存及运输。 本标准适用于公称直径不大于DN50、工作压力不大于1.6MPa的生活饮用水、饮用净水、热水(温度小于等于100℃)等内插卡压式不锈钢管材及管件。

Light gauge stainless steel pipes and insert.Pressfittings

CJJ 110-2006 管道直饮水系统技术规程

本规程适用于居住建筑、公共建筑等的管道直饮水系统设计、施工、验收、运行和管理。

Techncial specification of pipe system for fine drinking water

DIN EN 14652:2006 建筑物内水调节设备.薄膜分离设备.性能、安全和试验的要求.德文版本 EN 14652-2005

This European Standard applies to membrane separation systems with a particle rating below 1 mm, namely Microfiltration(MF), Ultrafiltration (UF), Nanofiltration(NF) and Reverse Osmosis(R.O.), for drinking water installations inside buildings, intended to remove from the drinking water marginal concentration of suspended and colloidal solids, microorganisms, organic molecules and to reduce the dissolved solids concentration, with a minimum pressure of PN10, connections between 15 NS and 100 NS and a maximum design temperature of at least 30 ? It specifies requirements relating to the construction, performances and methods of testing. It only concerns units which are permanently connected to the mains supply at the point-of-entry (POE) or the point-of-use (POU). This standard applies to membrane systems, whose elements may be partly or entirely washable or disposable according to the type of system. A membrane separation system may include,together with the separation device some pre-and /or post-treatment devices. For the scope of the present standard: - the separation device shall comply with the standard, i.e. without pre-and / or post-treatments; - in case pre-and/or post-treatment devices are forecast, each of them shall conform to the relevant standard. If so the complete system shall be considered conforming as a whole.

Water conditioning equipment inside buildings - Membrane separation devices - Requirements for performance, safety and testing; English version of DIN EN 14652:2006-03

JG/T 183-2006 住宅整体卫浴间

本标准规定了玻璃纤维增强塑料的住宅整体卫浴间(以下简称“卫浴间”)的术语、类型及尺寸系列、要求、试验方法、检验规则、标志、说明书、包装、储存、运输及安装等。 本标准适用于各类住宅具有洗浴、盥洗、便溺任意两种或两种以上洁具组合的卫浴间。公共、工业建筑等整体卫浴间也可参照应用。

Bathroom unit for housing

DIN EN 14743:2006 建筑物内水处理设备.软化剂.性能、安全和试验的要求

This European Standard specifies requirements relating to the construction and mode of operation and relevant methods of testing of automatic, salt-regenerated, cation exchange softeners for drinking water installations inside buildings which are permanently connected to the mains supply. Until EAS comes into force, the current national regulations remain applicable. NOTE Products intended for use in water supply systems should comply, when existing, with national regulations and testing arrangements that ensure fitness for contact with drinking water. The Member States relevant regulators and the EC Commission agreed on the principle of a future unique European Acceptance Scheme (EAS) which would provide a common testing and approval arrangement at European level. If and when the EAS is adopted, European Standards on products will be amended by the addition of an Annex Z/EAS under Mandate M/136 which will contain formal references to the testing, certification and product marking requirements of the EAS.

Water conditioning equipment inside buildings - Softeners - Requirements for performance, safety and testing; English version of DIN EN 14743:2006

AWWA C153/A21.53-2006 水供应易延展铁压缩装置

This standard describes 3-in. through 64-in. (76-mm through 1,600-mm) ductile-iron compact fittings to be used with ductile-iron pipe or pipe made of other materials with similar outside diameters for conveying water. Minimum working pressures by size range are as follows: 3-in. through 24-in. (76-mm through 610-mm): 350 psi (2,413 kPa); 30-in. through 48-in. (762-mm through 1,219-mm): 250 psi (1,724 kPa); and 54-in. through 64-in. (1,400-mm through 1,600-mm): 150 psi (1,034 kPa). Fittings are adequate for the rated working pressure plus a surge allowance of 100 psi or a surge allowance of half the rated working pressure, whichever is less. Fittings with mechanical joints are listed in this standard for the 3-in. through 48-in. (76-mm through 1,219-mm) sizes. The standard also may be used for fittings of these sizes with push-on joints or other joints as agreed on at the time of purchase. Fittings with push-on joints and flanged joints are listed in this standard for the 54-in. through 64-in. (1,400-mm through 1,600-mm) sizes. Fittings with flange joints are not discussed in this standard for sizes 3 in. through 48 in. (76 mm through 1,219 mm) because of the importance of standardized center-to-flange face dimensions for these sizes already described in ANSI*/AWWA C110/A21.10. Fittings with plain ends are listed for bends and reducers of the 3-in. through 64-in. (76-mm through 1,600-mm) size range and for tees and crosses of the 54-in. through 64-in. (1,400-mm through 1,600-mm) size range.

Ductile-Iron Compact Fittings for Water Service

ASTM F2021-06 塑料虹吸式屋面排水系统的设计和安装标准指南

The information provided in this standard guide is intended for use by designers and specifiers of siphonic roof drainage systems and their related components. Specifically, this guide addresses the use and limitations of plastic pipe and fittings in siphonic roof drainage systems where internal operating pressures are typically sub-atmospheric.1.1 This guide covers design and installation considerations for plastic siphonic roof drain systems for industrial, commercial, public, and residential buildings. Requirements for materials, pipe, and fittings are included.1.2 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this guide. Transition fittings for joining pipe and fittings of different manufacturers is provided for in the referenced pipe and fitting specification.1.3 In referee decisions, the SI units shall be used for metric-sized pipe and inch-pound units for pipe sized in the IPS system (ANSI B36.10). In all cases, the values given in parentheses are for information only.

Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems

CECS 185-2005 建筑排水中空壁消音硬聚氯乙烯管管道工程技术规程

本规程适用于新建、改建、扩建的高度不大于10Om的民用和工业建筑中，连续排水温度不高于40℃的中空壁消音硬聚氯乙烯管和中空壁消音硬聚氯乙烯螺旋管排水管道工程的设计、施工及验收。

Technical specification for unplasticized polyvinyl chloride double-wall noise-reducing pipeline engineering of water sewerage in buildings

BS EN 806-2:2005 人类消费用水的建筑物内部输水设备规范.设计

This document gives recommendations, and specifies requirements, on the design of potable water installations within buildings and for pipework outside buildings but within the premises (see EN 806-1) and applies to new installations, alterations and repairs.

Specifications for installations inside buildings conveying water for human consumption - Design

ASCE 12-05, 13-05 AND 14-05-2005 城市浅地表排水设计,安装以及操作和维护标准指南

Standard Guidelines for the Design of Urban Subsurface Drainage; Standard Guidelines for Installation of Urban Subsurface Drainage; Standard Guidelines for Operation and Maintenance of Urban Subsurface Drainage

Standard Guidelines for the Design of Urban Subsurface Drainage; Standard Guidelines for Installation of Urban Subsurface Drainage; Standard Guidelines for Operation and Maintenance of Urban Subsurface Drainage

ANSI/NSF 40(i17)-2005 住宅废水处理系统

Clarify requirements of welding, infiltration and exfiltration resistance, and access ports.

Residential Wastewater Treatment Systems

DIN EN 1123-1:2004 污水系统用带套管和孔座的纵向焊接热浸镀锌钢管及配件.第1部分:要求、检验和质量控制

This document specifies requirements, testing and quality control for pipes and fittings of hot-dipped, galvanized, longitudinally welded steel pipes with spigot and socket for the use in waste water systems normally operating under gravity or at a low level of pressure. These pipes and fittings are normally used for the conveyance of rainwater, household waste water and similar industrial sewage. This amendment adds the essential requirements, given in a Mandate under the Construction Procucts directive, to the standard.

Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control; German version EN 1123-1:1999 + A1:2004

DIN EN 1124-1:2004 污水系统用带套管和孔座的纵向焊接不锈钢管和配件.第1部分:要求、检验和质量控制

The document specifies requirements, testing and quality control for pipes and fittings of longitudinally welded stainless steel pipes for the conveyance of domestic waste water, surface water and similar industrial sewage. These pipes and fittings normally operate under gravity or at a low head of pressure. This amendment adds the essential requirements, given in a Mandate under the Construction Procucts directive, to the standard.

Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control; German version EN 1124-1:1999 + A1:2004

DB42/ 294-2004 超细干粉无管网灭火系统设计、施工及验收标准

本标准的第1章、第4章、第6章的6.3条、第8章为强制性的，其余为推荐性的。本标准共分九章和七个附录，内容包括：总则、规范性引用文件、术语与符号、系统的设计、系统的操作与控制、系统的安装施工、系统的调试、系统的验收、系统的维护管理。

Code for design,installation&acceptance fo the Super-fine powder non-pipeline network extinguishing system

CECS 171-2004（条文说明） 建筑给水铜管管道工程技术规程

Technical specification for copper pipeline engineering of building water supply

CECS 168-2004 建筑排水柔性接口铸铁管管道工程技术规程

本规程适用于新建、扩建和改建的民用和工业建筑内DN50mm~DN300mm、内压不大于0.3MPa、温度不高于80℃的、承插式和卡箍式连接的灰口铸铁管及其与套管件的生活排水管道、雨水管道、无侵蚀作用的工业生产废水管道的雨落管。对于室外架空和埋地的管道工程，按管道隔热、防腐等要求采取相关措施后，亦可参照采用。 本规程规定采用的建筑排水柔性接口铸造铁管材应为离心铸造工艺成型的管材；采用的配套管件应为机压砂型铸造造成型的管件。

Technical specification for flexible joint cast iron pipe system of building drainage

CECS 168-2004（条文说明） 建筑排水柔性接口铸铁管管道工程技术规程

Technical specification for flexible joint cast iron pipe system of building drainage

DB42/ 282-2004 细水雾灭火系统设计、施工及验收规范

本标准对应于美国国家标准ANSI/NFPA750“Standard on Water Mist Fire Protection Systems",与ANSI/NFPA750的一致性程度为非等效。本规范适用于新建、扩建、改建的建、构筑物中设置的用于灭火、抑火、控火、控温或保护设施（如除烟、冷却）的细水雾灭火系统设计、施工、调试、验收及维护。

Code for Design, Installation and Acceptance of Water Mist Fire Protection Systems

AWWA M54-2004 小型系统发展率水供应实践手册

This standard provides the requirements for coal-tar protective exterior coatings and interior linings used in the potable water supply industry for buried steel water pipelines.

Developing Rates for Small Systems; Manual of Water Supply Practices