P57 灌溉排水与水土保持工程 标准查询与下载

SL 312-2005 水土保持工程运行技术管理规程

本标准适用于各级水土保持主管部门批准实施的水土保持工程。

Code on operation and maintenance of soil and water conservation works

SL 317-2004 泵站安装及验收规范

本标准适用于符合下列手件的新建、扩建或改造的大型、中型灌溉、排水及工业、城镇供水、排水泵站机电设备的安装及验收，其他水泵机组的安装和验收可参照执行：装有水泵、叶1 1 装有水泵、叶轮直径900mm及以上或单机功率300kw及以上的轴流泵和混流泵机组。 2 装有水泵、进口直径在500mm及以上或单机功率在500kw及以上的离心泵机组。 3 叶轮直径500mm及以上的潜水泵。

Installation and acceptance specification for pumping station

SL 18-2004 渠道防渗工程技术规范

本标准适用于农田灌溉、发电引水、供水等渠道防沙工程的设计、施工、测验和管理。

Technique specification for seepage prevention engineering on canal

SL 13-2004 灌溉试验规范

本规范适用于以下四类试验； —作物及林、草蒸发蒸腾量观测试验； —作物及林、草灌溉制度试验； —作物劣态试验及灌溉效益试验； —灌溉方法及灌水技术试验。

Irrigation experiment standard

SL 302-2004 水坠坝技术规范

本规范适用于地震烈度为7度以下地区砂土、砂壤土、壤土及花岗岩和砂岩风化残积土修建的水坠坝(包括大型淤地坝工程、四等和五等水利水电工程)的设计与施工，中小型淤地坝工 程及五等以下水利水电工程的设计与施工可参照执行。

Technical specification for sluicing-siltation earth dam

ASTM D7014-04 双扭线筛网石筐和护堤垫的组装和放置的标准规程

Gabions and Revet Mattresses, as described in Specification A 975, are used to achieve soil stability and prevent soil erosion and are also used as retaining wall structures to resist movements due to gravity. Their ability to function properly depends on correct design and installation. This standard practice describes the proper installation of gabions and revet mattresses to ensure the products function as intended by the manufacturers. This practice offers a set of instructions for performing one or more specific operations and does not replace professional judgment. Not all aspects of this practice may be applicable in all situations. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a projectrsquo;many unique aspects.1.1 This specification covers standard practice for assembly, placement and filling of double-twisted wire mesh gabions and revet mattresses used for various erosion control, soil retention or freestanding structures. The product size, type and alignment must be determined by the user. Gabions and Revet Mattresses shall be installed in accordance with project plans and specifications when available.1.2 This standard is expressed in SI (metric) units. American (inch-pound) units are provided in parenthesis for information purposes.1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Assembly and Placement of Double-Twisted Wire Mesh Gabions and Revet Mattresses

SL 289-2003 水土保持治沟骨干工程技术规范

本规范适用于黄河流域水土流失严重地区的新建和配套加固骨干坝的建设和管理，其他流域和地区可参照执行。

Technical code of key dam for soil and water conservation

SL 267-2001 雨水集蓄利用工程技术规范

本规范适用于地表水、地下水缺乏或开采利用困难，且多年平均降水量大于250mm的半干旱地区和经常发生季节性缺水的湿润、半湿润山丘地区，以及海岛和沿海地区雨水集蓄利用工程的规划、设计、施工、验收与管理。

Technical code of practice for rainwater collection,storage and utilization

SL 254-2000 泵站技术改造规程

本规程适用于大、中型泵站的技术改造。小型泵站的技术改造，可参照执行。

Code of practice for technical renovation of pumping station

SL 255-2000 泵站技术管理规程（条文说明）

本规程适用于大、中型泵站的技术管理。小型泵站的技术管理可参照执行。

Code of technical management for pumping station (Description of articles)

SL 256-2000 机井技术规范

本规范适用于农业、工业与生活供水机井的建设与管理。

Technical criterion for water wells

DB62/T 651-2000 甘肃省水土保持治沟骨干工程建设管理技术标准

本标准规定了水土保持治沟骨干工程坝系规划和单项设计基本资料搜集、工程设计、工程施工、工程管理、检查验收、工程管护、产业开发与经营和科研管理。本标准适用于甘肃省黄河流域年侵蚀模数在5000t/k㎡以上的地区、其他流域和地区可参照使用。

Technical standards for construction and management of key soil and water conservation and gully control projects in Gansu Province

ASTM D6524-00(2006) 泥碳钢筋网弹力测量的标准试验方法

Resiliency may be used to control the quality of many TRMs. Resiliency may be indicative of a TRMrsquo;ability to retain original configuration after exposure to the stresses which may be exerted during manufacture, shipping, and installation. Resiliency is not generally indicative of field performance. The resiliency of TRMs may vary considerably depending on the pressure applied to the specimen during loading cycles. To minimize variation, specific sample size and applied pressure are indicated in this test method to ensure all results are comparable. To determine the effect of different pressure loadings on the final thickness of TRMs, use this test method. This test method may be used for acceptance testing of commercial shipments of TRMs, but caution is advised since information on between-laboratory precision is incomplete. Comparative tests, in accordance with 5.4.1 may be advisable. 5.4.1 In a case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are formed from a lot of material of the type in question. The test specimens should be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Studentrsquo;t-test for unpaired date and an acceptable probability level chosen by the two begun. If bias is found, either its cause must corrected, or the purchaser and be found and interpret future tests in supplier must agree to the light of the known bias. Note 18212;The user should be aware that the compressibility of the materials, their rebound characteristics, and the like will also be affected by the thickness of the TRMs following the time when they are rolled up on rolls shipped and stored.1.1 This test method covers the resiliency or recovery of turf reinforcement mats (TRMs) after they have been subjected to three cycles of loading at 689 kPa (100 psi) for 1 min/per cycle.1.2 This test method does not provide resiliency values for TRMs under variable normal compressive stresses. This test method determines nominal resiliency.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring the Resiliency of Turf Reinforcement Mats (TRMs)

SL/T 246-1999 灌溉与排水工程技术管理规定

本规程适用于各种类型的灌溉与排水工程的技术管理。

Code of practice for technical management of irrigation and drainage engineering

SL 236-1999 喷灌微灌工程技术管理规程

本规程适用于喷灌与微灌工程的工程管理、设备运行和维护保养、用水管理与田间测试以及技术经济后评价等。

Code of practice for technical management of sprinkler and micro irrigation project

SL 207-1998 节水灌溉技术规范

本规范适用于新建、扩建或改建的大田、菜地、果园、苗圃和草场等节水灌溉工程的规划、设计、施工、验收、管理和评价。

Technical standard for water saving irrigation

ANSI/ASAE S261.7-1996 非钢筋混凝土灌溉管系统的设计和安装

Guide to engineers in the design & installation of low or intermediate pressure nonreinforced concrete irrigation pipelines & for the preparation of detailed specifications for a particular installation. Restricted to pipelines with vents or stands open to the atmosphere or closed pipelines operating at less than 6 m (20 ft) of head. Systems designed and/or installed under this Standard shall utilize pipe conforming to one or more of the following types of nonreinforced concrete irrigation pipe: Pipelines with mortar joints; Pipelines with rubber gasket joints; Cast-in-place pipelines.

Design and Installation of Nonreinforced Concrete Irrigation Pipe Systems

DIN 19655:1996 灌溉.任务、基本原则、计划和方法

Irrigation - Problems, fundamental principles, planning and methods

BS 7562-3:1995 灌溉系统的规划、设计和安装.水灌溉要求指南

This Part of BS 7562 gives guidance and information on irrigation water requirements. It covers the subjects of crop water requirements, irrigation water requirements, scheduling and total volumes of water required for the design and operation of irrigation schemes.

Planning, design and installation of irrigation schemes - Guide to irrigation water requirements

SL 109-1995 农田排水试验规范

本规范适用于农田排水工程设计、施工和管理中为确定设计标准、设计参数、田间排水系统规格布局、水管理等而开展的试验。

Standard of land drainage test