P62 输、变电工程 标准查询与下载

DL/T 5136-2001 火力发电厂、变电所二次接线设计技术规程

Technical code for designing of electrical secondary wiring in fossil fuel power plants and substations

DL/T 5137-2001 电测量及电能计量装置设计技术规程

Technical code for designing electrical measuring and energy metering device

DL/T 5149-2001 220-500kV变电所计算机监控系统设计技术规程

Technical code for designing computerized monitoring and control system of 220-500kV substations

DL/T 5147-2001 35kV--220kV 架空送电线路测量技术规程

Designing technical rules for security and automaticity equipment of power system

DL/T 5130-2001 架空送电线路钢管杆设计技术规定

Technical regulation for design of steel transmission pole

SANS 10280:2001 南非常见环境用架空电力线路

Identifies the various factors to be taken into account in the design and construction of overhead power lines, and indicates ways and means of overcoming certain of the difficulties that can be encountered.

Overhead power lines for conditions prevailing in South Africa

IEEE 691-2001 传输结构的基础设计和测试用指南

The design of foundations for conventional transmission line structures, which include lattice towers, single or multiple shaft poles, H-frame structures, and anchors for guyed structures is presented in this guide.

IEEE Guide for Transmission Structure Foundation Design and Testing

DL/Z 713-2000 500kV变电所保护和控制设备抗扰度要求

Immunity requirement for protection and control equipment in 500kV substation

DL/T 5119-2000 农村小型化无人值班变电所.设计规程

Design code for the unattended miniaturization substation of rural electric network

DL/T 5122-2000 500kV架空送电线路勘测技术规程

Technical code of exploration and surveying for 500kV overhead transmission line

DL/T 5103-1999 35kV～110kV无人值班变电所设计规程

Design code for unattended substation of 35kV～110kV

DL 5106-1999 跨越电力线路架线施工规程

Operation code of cross power transmission line in installing the conductor

DL/T 5090-1999 水力发电厂过电压保护和绝缘配合设计技术导则

Overvoltage protection and insulation coordination design guide for hydro-power station

DL/T 5092-1999 110～500kV架空送电线路设计.技术规程

Technical code for designing 110～500kV overhead transmission line

ASTM D1036-99(2005) 木电杆的标准静态试验方法

Tests of wood poles are made to determine: 4.1.1 Data for use in establishing allowable stresses, 4.1.2 Data upon which to base economical pole line design, 4.1.3 Data on the strength properties of different species in pole sizes, 4.1.4 Data as to the influence of defects on the strength properties of poles, 4.1.5 Data as to the effect of preservatives and preservative treatments on the strength properties of poles, and 4.1.6 Data for correlating the strength properties of full-size poles with those of small clear specimens of the same species. Treating procedures to which poles have been subjected may introduce variables that prohibit direct comparisons between different groups of data. Complete information on the treating techniques shall form a part of the test records.1.1 These test methods cover determination of the bending strength and stiffness of wood poles. Knowledge of these properties is used in providing for reliable and economical design with poles of different species, size, or grade.1.2 Two test methods are included: the cantilever test method and the machine test method.1.3 Provision is also made for extracting small clear specimens from the butt section and determining static bending and compression parallel to grain strength values in accordance with Test Methods D 143.1.4 The procedures specified in these test methods apply to tests of either treated or untreated material.1.5 inch-pound-units;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods of Static Tests of Wood Poles

ASTM D1036-99 木电杆的标准静态试验方法

1.1 These test methods cover determination of the bending strength and stiffness of wood poles. Knowledge of these properties is used in providing for reliable and economical design with poles of different species, size, or grade. 1.2 Two test methods are included: the cantilever test method, and the machine test method. 1.3 Provision is also made for extracting small clear specimens from the butt section and determining static bending and compression parallel to grain strength values in accordance with Methods D143. 1.4 The procedures specified in these test methods apply to tests of either treated or untreated material. 1.5 The values stated in inch-pound units are to be regarded as the standard. SI values are given in parentheses and are provided for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods of Static Tests of Wood Poles

DL/T 5078-1997 农村小型化变电所设计规程

Design code for the miniaturization rural substation

DL/T 5056-1996 变电所总布置设计技术规程

Technical Code of General Plan Design for Substation

DL/T 5049-1995 架空送电线路大跨越工程勘测技术规定

Technical Regulation of Exploration and Surveying for Large Crossing Overhead Transmission Line

NRS 033-1996 使用木杆构筑物和裸导线的22kV以下（含）中压架空电力线路的设计，规划和施工指南

Guidelines for the application design and construction of medium voltage overhead power lines up to and including 22 kV, using wooden pole structures. Provides an example of overhead line design that complies with professionally accepted practices and th

Electricity distribution - Guidelines for the application design, planning and construction of medium voltage overhead power lines up to and including 22 kV, using wooden pole structures and bare conductors