P90 工业设备安装工程综合 标准查询与下载

SANS 10086-2:2006 用于爆燃性空气的设备的安装，检验和维护．第二部分：安装在矿井中的地下电气设备

Covers the installation, inspection and maintenance of electrical apparatus used underground in mining applications where atmospheres might be explosive owing to the presence of gases and dusts that are flammable in the presence of atmospheric oxygen. It

The installation, inspection and maintenance of equipment used in explosive atmospheres Part 2: Electrical apparatus installed underground in mines

BS EN 60950-22:2006 信息技术设备.安全性.室外安装的设备

Equipment covered This part of IEC 60950 applies to information technology equipment intended to be installed in an OUTDOOR LOCATION. The requirements for OUTDOOR EQUIPMENT also apply, where relevant, to empty OUTDOOR ENCLOSURES supplied for housing information technology equipment to be installed in an OUTDOOR LOCATION. Additional requirements Each installation may have particular requirements. Some examples are given in 4.2. In addition, requirements for protection of the OUTDOOR EQUIPMENT against the effects of direct lightning strikes are not covered by the standard. For information on this subject, see IEC 61024-1.

Information technology equipment - Safety - Equipment installed outdoors

ANSI/ACCA 3Manual S-2004 住宅用设备选择

Technical manual outlining the proper methods and procedures used to select and size residential cooling, furnaces and heat pump equipment.

Residential Equipment Selection

ASTM E213-02 金属管道超声检验的标准实施规程

1.1 This practice covers a procedure for detecting discontinuities in metal pipe and tubing during a volumetric examination using ultrasonic methods. Specific techniques of the ultrasonic method to which this practice applies include pulse-reflection techniques, both contact and non-contact (for example, as described in Guide E 1774), and angle beam immersion techniques. Artificial reflectors consisting of longitudinal, and, when specified by the using party or parties, transverse reference notches placed on the surfaces of a reference standard are employed as the primary means of standardizing the ultrasonic system.1.2 This practice is intended for use with tubular products having outside diameters approximately 1/2 in. (12.7 mm) and larger, provided that the examination parameters comply with and satisfy the requirements of Section 12. These procedures have been successful with smaller sizes. These may be specified upon contractual agreement between the using parties. These procedures are intended to ensure that proper beam angles and beam shapes are used to provide full volume coverage of pipes and tubes, including those with low ratios of outside diameter-to-wall thickness, and to avoid spurious signal responses when examining small-diameter, thin-wall tubes.1.3 The procedure in Annex Annex A1 is applicable to pipe and tubing used in nuclear and other special and safety applications. The procedure in Annex Annex A2 may be used to determine the helical scan pitch.1.4 This practice does not establish acceptance criteria; they must be specified by the using party or parties.1.5 The values stated in inch-pound units are to be regarded as standard. The SI equivalents are in parentheses and may be approximate.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Ultrasonic Examination of Metal Pipe and Tubing

ASME B31.8-1999 气体传送和分配管道系统

Gas transmission and distribution piping systems

SANS 4994:1987 增强塑料容器的设计与施工

Specifies requirements for the design, materials, construction, inspection, testing and erection of vessels and tanks in reinforced plastics, consisting of a polyester, epoxy or furane resin system reinforced with glass fibres, manufactured by the wet lay-up process. Constructions both with and without a lining of thermoplastics are included.

Design and construction of vessels and tanks in reinforced plastics

ISO 11375:1998 建筑施工机械和设备 术语和定义

This International Standard specifies terminology for machines and equipment used in the building construction industry, for ease for reference and for use in discussions on standardization activities. This International Standard refers to machines and equipment used on construction sites. They are divided into five groups: — assembly of machines and components for installation and extraction of piles; — equipment for preparing, conveying and compaction of concrete, mortar and processing reinforcement and formwork; — machinery and equipment for aggregate processing; — equipment for finishing work and maintenance; — machinery and equipment for general use in construction processes. The machinery and equipment presented in these particular groups are used primarily in building processes. This International Standard does not include groups of building machines such as earth-moving machinery, cranes, lifting and access machinery.

Building construction machinery and equipment - Terms and definitions

CECS 98-1998 浆体长距离管道输送工程设计规程

本规程适用于固液两相高浓度拟均质流浆体长距离压力管道输送新建工程的设计。对于改扩建工程，可参照本规范执行。

Design code of long distance pipeline engineering for slurry transportation

ASTM E213-98 金属管道的超声检验

1.1 This practice covers a procedure for detecting discontinuities in metal pipe and tubing using pulse-reflection ultrasonic contact or immersion angle beam techniques. Artificial discontinuities consisting of longitudinal reference notches are employed as the primary means of calibrating the ultrasonic system. If transverse as well as longitudinal examination is desired, a procedure for employing transverse notches is provided. 1.2 This practice is intended for use with tubular products having outside diameters approximately 1/2 in. (12.7 mm) and larger, provided that the examination parameters comply with and satisfy the requirements of Section 12. These procedures have been used successfully for smaller sizes, however, and may be specified upon contractural agreement between the using parties. Note 1-Exercise caution when examining pipe or tubes near or below the 1/2-in. specified limit. Certain combinations of search unit size, frequency, thin wall thicknesses, and small diameters could cause generation of unwanted sound waves that may produce erroneous test results. 1.3 This practice does not establish acceptance criteria; they must be specified by the using party or parties. 1.4 The values stated in inch-pound units are to be regarded as standard. The SI equivalents are in parentheses and may be approximate. 1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Ultrasonic Examination of Metal Pipe and Tubing

NF C17-100:1997 防雷电保护结构.避雷针的安装

Protection of structures against lightning. Installation of lightning Protective system.

ISO 7369:1995 管道工程 柔性金属软管 一般术语词汇 两种语言版

Pipework - Flexible metallic hoses - Vocabulary of general terms

ISO 7658:1984 管道工程 带绕金属软管 特性试验和验证

Pipework; Stripwound flexible metal hoses; Testing and verification of characteristics

ISO/TR 8545:1984 技术制图 设备 自动控制的图形符号

Technical drawings; Installations; Graphical symbols for automatic control

ISO 7369:1983 管道工程.柔性金属管.一般术语词汇.两种语言版

Pipework; Flexible metallic hoses; Vocabulary of general terms Bilingual edition

ANSI Y32.4-1977 建筑结构和楼房结构示意图中管路设施的图形符号

1. SCOPE: This standard presents graphic symbols for plumbing fixtures for use on drawings created by architects, engineers and plumbing contractors. Included in Section 5 are symbols for the more common fixtures found in the average building. Included in Section 6 are symbols for the special types of fixtures utilized in hospitals and institutions. 2. PURPOSE: By the use of these symbols on their plans, designers and builders will have a uniform method for indicating plumbing fixtures and related items. Drawings will thus be more concise and more easily understood.

Graphic symbols for plumbing fixtures for diagrams used in architecture and building construction

CECS 72-1995 建筑与建筑群综合布线系统工程设计规范

Code for engineering design of integrated wiring system for buildings and complexes