P98 水利工程施工机械设备 标准查询与下载

SL 531-2012 大坝安全监测仪器安装标准

本标准适用于各级水库大坝嫉测仪器安装与管理。20Om以上或特别重要大坝的安全监测仪器安装应进行专门研究。

Standard for installation of dam safety monitoring instruments

SL 530-2012 大坝安全监测仪器检验测试规程

本标准适用于现场安装埋设前的大坝安全监测仪器（传感器）的实验室第三方检验测试。用于大坝安全监测的仪器应满足本标准的要求，其他水利工程的安全监测仪器安装埋设前的检验测试可参照本标准。

Specification for vertification and test of dam safety monitoring instruments

SL 548-2012 泵站现场测试与安全检测规程

本标准适用于大中型泵站的现场性能测试和安全检测。小型泵站的现场性能测试和安全检测可参照执行。

The code of practice of field testing of performance and safety for pumping station

SL 554-2011 橡胶坝坝袋

Rubber dam bag

SL 536-2011 X射线衍射应力测定装置校验方法

Calibration method of X-ray diffraction stress measuring device

SL 547-2011 水工金属结构残余应力测试方法 X射线衍射法

Test method for residual stress of hydraulic metal structures X-ray diffraction method

SL 545-2011 铸铁闸门技术条件

Cast iron gate technical conditions

SL 542-2011 水利水电建设用门座起重机

本标准规定了水利水电建设用门座起重机（以下简称起重机）的产品型式及参数、技术要求、试验方法、检验规则、信息标识、包装、运输与储存、安装、拆卸与维修、工程验收、使用与管理、设备搬迁和报废。 本标准适用于水利水电工程混凝土浇筑和水工金属结构件安装等工作的起重机。火电厂、船厂和露天作业场用的同类起重机亦可参照使用。本标准不适用于汽车、轮胎、履带及浮式起重机。

Portal crane for water resources and electric power construction

SL 553-2011 全油压控制水轮机调压阀

本标准规定了水电站用全油压控制水轮机调压阀的术语及定义，型式及参数，技术要求，试验及验收，标志、包装与质保。 本标准适用于全油压控制水轮机调压阀（以下简称调压阀）。

Full-hydraulic control pressure regulating valve of hydraulic turbine

SL 507-2010 卷扬式启闭机系列参数

本标准适用于水利水电工程启闭机平面闸门、快速闸门和弧形闸门的固定卷扬式启闭机。

Series parameters for wire rope hoist

SL 491-2010 螺杆式启闭机系列参数

本标准规定了螺杆式启闭机系列参数，适用于水利水电工程启闭中小型闸门的螺杆式启闭机。

Series parameters for hoist with screw stem

JGJ 88-2010 龙门架及井架物料提升机安全技术规范

本规范适用于建筑工程和市政工程所使用的以卷扬机或曳引机为动力、吊笼沿导轨垂直运行的物料提升机的设计、制作、安装、拆除及使用。不适用于电梯、矿井提升机及升降平台。

Technical code for safety of gantry frame and headframe hoisters

SL 472-2010 水利工程设备制造监理规范

本标准适用于我国境内大、中型水利工程建设项目设备制造阶段的监理。小型水利工程建设项目设备制造监理可参照执行。

Specification for equipment manufacturing supervision of water resources projects

ISO 21329:2004 石油和天然气工业.管道运输系统.机械连接器的试验过程

This International Standard specifies requirements and provides guidance for the testing of mechanical connectors for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. The tests specified in this International Standard are intended to form part of the design verification process for connectors. They provide objective evidence that connectors conform to a defined performance envelope. This International Standard does not cover the use of design procedures as part of the qualification process for mechanical connectors, nor does it address fabrication and quality control. However, it can be used as input to a qualification procedure. Although its principles can be applied, this International Standard does not address a) connectors that are designed to rotate in use, b) manifolds, c) topsides pipework or piping, d) flanges, e) connectors used in pipelines installed by reeling or J-tube pulls, f) factory acceptance testing, g) statistical bases for risk analysis.

Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors

BS EN 14163:2001 石油和天然气工业.管道运输系统.管道焊接

This European Standard specifies the requirements for producing and inspecting girth, branch and fillet welds in the pipeline part of pipeline transportation systems for the petroleum and natural gas industries meeting the requirements of ISO 13623. On-land supply systems used by the gas supply industry are excluded from the scope of the International Standard. This European Standard is applicable to the requirements for welding of carbon and low-alloy steel pipes. Application is restricted to pipes with a diameter of 20 mm and larger and wall thickness of 3 mm or more, and a specified minimum yield strength of 555 MPa or less. It is also applicable to welding into pipelines, items such as spools, risers, launchers/receivers, fittings, flanges and “pups” to pipeline valves. The welding processes covered are shielded metal arc welding, gas tungsten arc welding, gas metal arc welding, flux-cored arc welding with and without shielding gas, and submerged arc welding. This European Standard is not applicable to flash girth welding, resistance welding, solid-phase welding or other one-shot welding processes, nor to longitudinal welds in pipe or fittings, to “hot-tap” welding of pipelines in service or to the welding of process piping outside of the scope of ISO 13623. NOTE Additional requirements may be necessary for welding of pipeline for particular pipeline operating conditions. These can include limitations on maximum hardness or strength, minimum impact toughness values, crack tip-opening displacement, all weld metal tensile testing or bend testing, thermal stress relief or others. Where appropriate, these additional requirements should be added to the requirements of this European Standard in a project-specific supplement.

Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines

SL 230-1998 混凝土坝养护修理规程

本规程适用于一、二、三、四级混凝土坝和同级土石坝的水工混凝土建筑物的养护修理。其他水工混凝土建筑物可参照执行。

Specifications for maintenance and repair of concrete dam

ARMY MIL-H-2514 D NOTICE 1-1998 1.800和3.000 磅空投打桩机钉锤

This commercial item description covers brown kraft paper used for general wrapping applications.

HAMMERS, PILEDRIVER, DROP; 1,800 AND 3,000 POUNDS

SL 130-1995 混凝土试模检验方法

本方法适用于新的、使用中和检修后的混凝土试模的检验。

Test method for concrete test-moulds

SL 138-1995 混凝土标准养护室检验方法

本方法适用于新建的、使用中和维修后的混凝土标准养护室的检验。

Test method for concrete curing chamber

SL 136-1995 混凝土绝热温升测定仪校验方法

本方法适用于新的、使用中和修理后的混凝土绝热温升测定仪的校验。

Test method for adiabatic temperature rise tester