Q10 建材产品综合 标准查询与下载

ASTM E603-01 房间着火实验标准指南

1.1 This guide addresses means of conducting full-scale fire experiments that evaluate the fire-test-response characteristics of materials, products, or assemblies under actual fire conditions.1.2 It is intended as a guide for the design of the experiment and for the use and interpretation of its results. The guide is also useful for establishing laboratory conditions that simulate a given set of fire conditions to the greatest extent possible.1.3 This guide allows users to obtain fire-test-response characteristics of materials, products, or assemblies, which are useful data for describing or appraising their fire performance under actual fire conditions.1.3.1 The results of experiments conducted in accordance with this guide are also useful elements for making regulatory decisions regarding fire safety requirements. The use for regulatory purposes of data obtained from experiments conducted using this guide requires that certain conditions and criteria be specified by the regulating authority.1.4 The rationale for conducting room fire experiments according to this guide is shown in 1.5-1.8 1.5 Room fire experiments are a means of generating input data for computer fire models and for providing output data with which to compare modeling results.1.6 One of the major reasons for conducting room fire experiments is as an experimental means of assessing the potential fire hazard associated with the use of a material or product in a particular application. This should be borne in mind when designing nonstandard experiments.1.7 A rationale for conducting room fire experiments is the case when smaller-scale fire tests inadequately represent end-use applications.1.8 A further rationale for conducting room fire experiments is to verify the results obtained with smaller scale tests, to understand the scaling parameters for such tests.1.9 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Room Fire Experiments

ASTM D3675-01 用辐射热源作软质多孔材料的表面可燃性的标准试验方法

1.1 This is a fire test response standard. 1.2 This test method covers the measurement of surface flammability of flexible cellular materials. 1.3 This standard should be used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions and should not be used to describe or appraise the fire-hazard or fire-risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire-hazard assessment or a fire-risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard or fire risk of a particular end use. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment. Specific information about hazards is given in Section 7.Note 18212;There is no similar or equivalent ISO standard.

Standard Test Method for Surface Flammability of Flexible Cellular Materials Using A Radiant Heat Energy Source

JC/T 873-2000 长石化学分析方法

Methods of chemical analysis of feldspar

DIN 30672:2000 持续工作温度不超过50℃的地下和水下管道外部有机防腐涂层.带材和可收缩材料

The document applies to external organic coatings for the corrosion protection of buried and immersed pipelines for continuous operating temperatures up to 50 ? especially tapes and shrinkable material.

External organic coatings for the corrosion protection of buried and immersed pipelines for continuous operating temperatures up to 50 °C - Tapes and shrinkable materials

ISO 4709:2000 复合软木 衬垫材料 分级体系 要求、取样、包装和标记

This International Standard gives a classification system for composition cork intended to be used as gaskets in the mechanical industry. It provides a means for specifying or describing the relevant properties. Since not all properties that contribute to gasket performance are included, the use of this system is limited to the selection of materials in accordance with specified requirements.

Composition cork - Gasket material - Classification system, requirements, sampling, packaging and marking

WB/T 1013-2000 玻镁复合保温屋面板

Glass fiber reinforced and magnesium oxy-chloride gelatinous materials composite heat-shielded roof plate

ASTM E84-00a 建筑材料表面燃烧特性的标准试验方法

1.1 This fire-test-response standard for the comparative surface burning behavior of building materials is applicable to exposed surfaces such as walls and ceilings. The test is conducted with the specimen in the ceiling position with the surface to be evaluated exposed face down to the ignition source. The material, product, or assembly shall be capable of being mounted in the test position during the test. Thus, the specimen shall either be self-supporting by its own structural quality, held in place by added supports along the test surface, or secured from the back side.1.2 The purpose of this test method is to determine the relative burning behavior of the material by observing the flame spread along the specimen. Flame spread and smoke developed index are reported. However, there is not necessarily a relationship between these two measurements.1.3 The use of supporting materials on the underside of the test specimen has the ability to lower the flame spread index from those which might be obtained if the specimen could be tested without such support. These test results do not necessarily relate to indices obtained by testing materials without such support.1.4 Testing of materials that melt, drip, or delaminate to such a degree that the continuity of the flame front is destroyed, results in low flame spread indices that do not relate directly to indices obtained by testing materials that remain in place.1.5 The values stated in inch-pound units are to be regarded as the standard.1.6 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of the standard.1.7 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Surface Burning Characteristics of Building Materials

ASTM C1375-00 用于测试建筑物密封和胶粘剂的基质的标准指南

1.1 This guide describes the recommended standard substrates and their recommended surface preparation for use in standard tests of building seals and sealants.

Standard Guide for Substrates Used in Testing Building Seals and Sealants

ASTM E119-00a 建筑结构和材料防火试验的标准试验方法

1.1 The test methods described in this fire-test-response standard are applicable to assemblies of masonry units and to composite assemblies of structural materials for buildings, including bearing and other walls and partitions, columns, girders, beams, slabs, and composite slab and beam assemblies for floors and roofs. They are also applicable to other assemblies and structural units that constitute permanent integral parts of a finished building.1.2 It is the intent that classifications shall register comparative performance to specific fire-test conditions during the period of exposure and shall not be construed as having determined suitability for use under other conditions or after fire exposure.1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.1.4 These test methods prescribe a standard fire exposure for comparing the test results of building construction assemblies. The results of these tests are one factor in assessing predicted fire performance of building construction and assemblies. Application of these test results to predict the performance of actual building construction requires the evaluation of test conditions.1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.7 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Test Methods for Fire Tests of Building Construction and Materials

ASTM C4-00 粘土和多孔粘土排水管的标准规范

1.1 This specification establishes the criteria for acceptance, prior to installation, of drain tile and perforated drain tile to be used for underdrainage, filter fields, leaching fields, and similar subdrainage installations.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety hazards caveat pertains only to the Test Methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;Attention is called to Test Methods C 301 and Terminology C 896.

Standard Specification for Clay Drain Tile and Perforated Clay Drain Tile

ASTM D806-00 硬化土-水泥混合料中水泥含量的标准试验方法

1.1 This test method covers the determination by chemical analysis of cement content of hardened soil-cement mixtures. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard precautions, see section 5.

Standard Test Method for Cement Content of Hardened Soil-Cement Mixtures

ASTM C1375-00(2005) 用于测试建筑物密封和胶粘剂的基质的标准指南

The guide provides recommendations for substrates and methods of surface preparation to be used in comparative tests of building seals and sealants.1.1 This guide describes the recommended standard substrates and their recommended surface preparation for use in standard tests of building seals and sealants.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Substrates Used in Testing Building Seals and Sealants

ASTM D806-00(2006) 硬化土-水泥混合料中水泥含量的标准试验方法

This test method determines cement content in mixtures of cement with soil or aggregate by chemical analysis. It was developed primarily for testing samples for which a significant degree of cement hydration or hardening has taken place. Test Methods D 2901 or D 5982 may be used for determining cement content of freshly mixed soil-cement mixtures. This test method is based on determination by chemical analysis of the calcium oxide (CaO) content of the sample. The method may not be applicable to soil-cement materials containing soils or aggregates which yield significant amounts of dissolved calcium oxide (CaO) under the conditions of the test. Note 18212;The agency performing this test method can be evaluated in accordance with Practice D 3740. Not withstanding statements on precision and bias contained in this test method: the precision of this test method is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing. Users of this test method are cautioned that compliance with Practice D 3740 does not, in itself, ensure reliable testing. Reliable testing depends on many factors; Practice D 3740 provides a means of evaluating some of these factors.1.1 This test method covers the determination by chemical analysis of cement content of hardened soil-cement mixtures.1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026.1.3 The values stated in SI units are to be regarded as the standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard precautions, see Section .

Standard Test Method for Cement Content of Hardened Soil-Cement Mixtures

DB52/T 423-1999 建材产品中废渣掺加量的测定方法

Method for Determination of Addition of Waste Slag in Building Material Products

DB50/ 1.2-1999 劣质铝合金建筑型材判定规则

本标准规定了劣质铝合金建筑型材的质量判定界限指标，试验方法和检验规则。本标准适用于质量监督检查中对劣质铝合金建筑型材的判定。

Judgment rules for low-quality aluminum alloy building profiles

JC/T 855-1999 蒸压加气混凝土板钢筋涂层防锈性能试验方法

Test method of anti-corrosion performance for the coated reinforcement in autoclaved aerated concrete slabs

DB35/T 93-1999 玄武岩建筑板材

本标准规定了玄武岩建筑板材（以下简称板材）的产品分类、技术要求、试验方法、检验规则、标志、包装、运输、贮存与使用说明等。本标准适用于建筑装饰用的天然玄武岩板材。其他用途的天然玄武岩板材也可参照采用。

Basalt building panels

JIS A 1412-2:1999 隔热材料的热阻及相关的性能的试验方法.第2部分:热流计设备

この規格は，平板状の熱絶縁材の，定常状態における熱抵抗，熱伝導率などの伝熱特性を熱流計法(HFM法)によって測定する方法について規定する。この測定方法は，熱流計を介して，標準板と試験体の熱抵抗を比較して，熱抵抗，熱伝導率などの関連伝熱特性を求めるので，平板法による二次測定法又は比較測定法である。この方法は，1.7.2による厚さの範囲で，0.1 m・K／Wよりも大きい熱抵抗をもつ試験体に適用できる。

Test method for thermal resistance and related properties of thermal insulations -- Part 2: Heat flow meter apparatus

JIS A 1412-1:1999 隔热材料的热阻及相关的性能的试验方法.第1部分：带防护罩的加热板装置

この規格は，平板状の熱絶縁材の定常状態における熱抵抗，熱伝導率などの伝熱特性を保護熱板法(GHP法)によって測定する方法について規定する。この測定方法は，定常状態の温度及び加熱電力(熱流量)更に厚さを測定して，熱抵抗，熱伝導率などの伝熱特性を求めることができるので，平板法による絶対測定法又は基準測定法である。この方法は，1.6.4による厚さの範囲で，0.1 m・K/Wよりも大きい熱抵抗をもつ試験体に適用できる。0.02 m・K／W程度の熱抵抗まで測定してもよいが，測定の正確さは制約される。参考“保護熱板（Guarded hot plate)”という用語を装置全体に対して用いている。このことから保後熱板法又はGHP法測定装置と呼ぶ。锅内では，絶対測定法として熱伝導率を直接測定できることから“平板直接法”と呼ぶこともある。。

Test method for thermal resistance and related properties of thermal insulations -- Part 1: Guarded hot plate apparatus

JIS A 1412-3:1999 绝热材料的耐热和相关特性的试验方法.第3部分:环形管装置

この規格は，円筒状の熱絶縁材(保温筒)の，定常状態における熱抵抗，熱伝導率などの伝熱特性を円筒法によって測定する方法について規定する。 備考 この規格には，操作方法，装置特性も含まれるが，装置の形状及び寸法を標準化するものではない。

Test method for thermal resistance and related properties of thermal insulations -- Part 3: Circular pipe apparatus