Q10 建材产品综合 标准查询与下载

SS EN 15167-1-2008 在混凝土、灰泥和水泥浆中使用的研磨粒状高炉矿渣规范.第1部分:定义、规范,与合格准则

This Singapore Standard specifies requirements for the chemical and physical properties as well as quality control procedures for ground granulated blastfurnace slag for use as a type II addition in the production of concrete, including in particular cast-in-situ or prefabricated structural concrete conforming to SS EN 206-1. Ground granulated blastfurnace slag conforming to this Singapore Standard may also be used in mortars and grouts. Ground granulated blastfurnace slag containing any added materials other than grinding aids, is not within the scope of this Singapore Standard. It is also not within the scope of this Singapore Standard to specify provisions governing the practical application of ground granulated blastfurnace slag in the production of concrete, mortar or grout, i.e. requirements concerning composition, mixing, placing, curing etc. As regards such provisions, reference should be made to relevant standards, such as SS EN 206-1.

Specification for ground granulated blast furnace slag for use in concrete, mortar and grout - Part 1: Definitions, specifications and conformity criteria

SS EN 934-2-2008 混凝土、灰泥和水泥浆用掺合料规范.第2部分:混凝土掺合料.定义、要求、合格,标志和标签

This Singapore Standard specifies definitions and requirements for admixtures for use in concrete. It covers admixtures for plain, reinforced and prestressed concrete which are used in site mixed, ready mixed concrete and precast concrete. The performance requirements in this standard apply to admixtures used in concrete of normal consistence. They may not be applicable to admixtures intended for other types of concrete such as semi-dry and earth moist mixes. Provisions governing the practical application of admixtures in the production of concrete, i.e. requirements concerning composition, mixing, placing, curing etc. of concrete containing admixtures are not part of this standard.

Specification for Admixtures for concrete,mortar and grout - Part 2: Concrete admixtures - Definitions, requirements, conformity, marking and labelling

SS EN 934-6-2008 混凝土、灰泥和水泥浆用掺合料规范.第6部分:取样、合格控制,与合格评定

This Singapore Standard specifies procedures for sampling, conformity control and evaluation of conformity, for admixtures according to the series SS EN 934.

Specification for Admixtures for concrete,mortar and grout - Part 6: Sampling, conformity control and evaluation of conformity

JG/T 235-2008 建筑反射隔热涂料

本标准规定了建筑反射隔热涂料的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于工业与民用建筑屋面和外墙的隔热工程。

Architectural reflective thermal insulation coatings

JIS A 1470-1:2008 建筑材料的水蒸气吸附/解吸性能的测定.第1部分:湿度变化效应

この規格は，主として内装材などの湿度変動による建築材料のI日周期(12時間吸湿，12時間放湿)におサる吸放湿性の試験方法について規定する。

Determination of water vapour adsorption / desorption properties for building materials -- Part 1: Response to humidity variation

JIS A 1470-2:2008 建筑材料的水蒸气吸附和解吸性能的测定.第2部分:温度效应

この規格は，断湿した気密な箱（密閉箱)に，主に内装材などに使用する建築材料を入れ，密閉箱の外部から温度変動を与えた場合の吸放湿性の試験方法について規定する。

Determination of water vapour adsorption/desorption properties for building materials -- Part 2 : Response to temperature variation

UL BUILDING MATERIALS-2008 建筑材料目录

Building Materials Directory

Building Materials Directory

ASTM D5050-08 石灰窑尘埃和硅酸盐水泥窑尘埃的商用标准指南

This guide provides a list of applications and appropriate test procedures to establish selected uses for the lime kiln dusts and Portland cement kiln dusts. The lime kiln dusts and Portland cement kiln dusts covered by this guide may vary in composition from one source to another. It is therefore advised that the use of such products be undertaken only after their specific compositions, physical properties, performance characteristics, and the anticipated variabilities have been evaluated for the service intended. Until the degree of variability in the dust source or sources has been established, frequent performance testing is recommended. Specifications should be prepared to facilitate uses, environmental protection, and engineering designs by the responsible persons.1.1 This guide is intended to evaluate and describe lime kiln dusts and Portland cement kiln dusts for uses in commercial applications. This guide is not intended to cover uses for lime or Portland cement. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Commercial Use of Lime Kiln Dusts and Portland Cement Kiln Dusts

ISO 10456:2007 建筑材料和制品.温湿特性.列表式设计值和测定热性能申报值和设计值的程序

This International Standard specifies methods for the determination of declared and design thermal values for thermally homogeneous building materials and products, together with procedures to convert values obtained under one set of conditions to those valid for another set of conditions. These procedures are valid for design ambient temperatures between −30 °C and +60 °C. This International Standard provides conversion coefficients for temperature and for moisture. These coefficients are valid for mean temperatures between 0 °C and 30 °C. This International Standard also provides design data in tabular form for use in heat and moisture transfer calculations, for thermally homogeneous materials and products commonly used in building construction.

Building materials and products - Hygrothermal properties - Tabulated design values and procedures for determining declared and design thermal values

JIS R 9011 ERRATUM 1:2007 勘误表

ERRATUM

JC/T 791-2007 轮窑热平衡、热效率测定与计算方法

本标准适用于使用固体燃料的砖瓦工业轮窑。使用其他燃料的砖瓦工业轮窑可参照执行。 本标准适用于使用固体燃料烧制以粘土，页岩、粉煤灰、煤矸石为原料的砖瓦的轮窑。

The method for the measurement and calculation of heat balance, heat efaciencyof annular kilns

JC/T 792-2007 隧道式砖瓦干燥室热平衡、热效率测定与计算方法

本标准适用于以粘土、页岩、粉煤灰、煤矸石为原料的砖瓦坯体的隧道干燥室热平衡、热效率测定与计算。

The methods for the measurement and calculation of heat balance, heat efficiency of tunnel dryer

JC/T 793-2007 隧道式干燥室-轮窑体系热效率、单位热耗、单位煤耗计算方法

本标准适用于砖瓦企业以固体燃料为热源生产粘土、页岩、粉煤灰、煤矸石砖瓦的隧道式干燥室一轮窑体系。其它原料的砖瓦隧道式干燥室一轮窑体系可参照执行。

The methods for the calculation of the efficiency, unit heat consumption and unit coal consumption of tunnel dryer annular kiln system

BS DD CEN/TS 14754-1:2007 养护剂.试验方法.普通养护剂保水率的测定

This Technical Specification describes a procedure for determining the ability of a curing compound to prevent the evaporation of water from young concrete when applied immediately after the bleed water has evaporated. NOTE The procedure involves application to a horizontal surface; it may not be applicable for use on vertical or sloping surfaces.

Curing compounds - Test methods - Determination of water retention efficiency of common curing compounds

NF P92-800-4:2007 建筑产品和建筑部件的燃烧分类.第4部分:用烟雾控制系统耐火试验中试验数据进行分类

Fire classification of construction products and building elements - Part 4 : classification using test data from fire resistance tests on smoke control systems.

ANSI Z21.94a-2007 自动可燃蒸气传感系统和部件

Details test and examination criteria for flammable vapor sensor systems and components for use in gas-burning appliances. This standard applies to a flammable vapor sensor or system capable of operating throughout a temperature range of 32鳩 (0鳦) to 12

Automatic Flammable Vapor Sensor Systems and Components (same as CSA 6.31a)

ISO 21129:2007 建筑材料和产品的温湿性能.水蒸汽透过率特性测定.箱法

This International Standard specifies a box method for determining the water-vapour permeability of building materials. The box method is used primarily to measure the water-vapour permeance of materials that have low water-vapour resistance, in which the influence of the surface-humidity transmission-resistance cannot be ignored.

Hygrothermal performance of building materials and products - Determination of water-vapour transmission properties - Box method

DIN EN 13501-4:2007 施工产品和建筑部件燃烧性能分类.第4部分:烟控制系统构件耐火性试验用数据分类

This European Standard specifies the procedure for classification of components of smoke control systems, using data from fire resistance tests which are within the field of application of the relevant test methods.Classification on the basis of extended application is not within the scope of this European Standard,however for extended application the same classes are used as specified in this European Standard. Products covered by this European Standard are: - smoke control ducts; - smoke control dampers; - smoke barriers; - powered smoke and heat exhaust ventilators(fans),including connectors; - natural smoke and heat exhaust ventilators. Relevant documents which include the relevant test methods which have been prepared for these products are listed in Clause 2.

Fire classification of construction products and building elements - Part 4: Classification using data from fire resistance tests on components of smoke control systems; German version EN 13501-4:2007

DIN EN 14390:2007 着火试验.表面产品用大范围室内参考试验

This European Standard specifies a test method to evaluate the reaction to fire performance of building products. A fire is simulated which under well-ventilated conditions starts in a corner of a small room with a single open doorway. The method is intended to evaluate the contribution of a surface product to fire growth in a room configuration, using a specified ignition source. It constitutes a reference test for this type of product within the European classification system for reaction to fire performance of construction products. The method is particularly suitable for construction products which cannot be tested in their end use application in a small or intermediate laboratory scale. The method can also be used to assess the effect of an insulating substrate on the product performance. A test performed in accordance with the method specified in this European Standard provides data for the early stages of a fire from ignition up to flashover. The method is not intended to evaluate floor coverings. It may not be suitable for some free-standing products because their integrity, when exposed to fire, could h,ave a decisive influence on their behaviour. NOTE The term "surface product" as used in the title and scope of this European Standard specifically relates to internal surface linings, assemblies, pipes and pipe insulation products used in buildings.

Fire test - Large-scale room reference test for surface products; English version of DIN EN 14390:2007-04

DIN EN 13969:2007 防水用柔性薄板.包括沥青底层制箱用薄板的沥青防潮薄板.定义和特性

This document specifies definitions and characteristics of flexible reinforced bitumen sheets for which the intended use is as damp proofing for buildings. including basement tanking.It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this standard.

Flexible sheets for waterproofing - Bitumen damp proof sheets including bitumen basement tanking sheets - Definitions and characteristics English version of DIN EN 13969:2007-03