共找到 233 条与 工业技术玻璃 相关的标准,共 16 页
Glass containers - Thermal shock resistance and thermal shock endurance - Test methods (ISO 7459:2004); German version EN ISO 7459:2004
This European Standard specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.
Glass containers - Resistance to vertical load - Test method (ISO 8113:2004); German version EN ISO 8113:2004
This part of ISO 14368 specifies the nomenclature of defects and the test methods to check them, with minimum physical and aesthetic requirements, for circular mineral and sapphire watch-glasses.
Mineral and sapphire watch-glasses - Qualitative criteria and test methods
This part of ISO 14368 specifies the nomenclature of defects and the test methods to check them, with minimum physical and aesthetic requirements, for circular mineral and sapphire watch-glasses.
Mineral and sapphire watch-glasses - Part 3: Qualitative criteria and test methods
The document describes a method for the measurement of scattered light of a pane to be tested under a small angle to the optical axis. The method is applicable for plane and bended safety glazing materials for vehicle glazing also when the pane is installed, especially windscreens.#,,#
Road vehicles - Measurement of scattered light of safety glazing materials for vehicle glazing - Part 2: Image-mapping method
この規格は,主として建築物の外壁,開口部などに使用する倍強度ガラスについて規定する。
Heat-strengthened glass
この規格は,主として建築及び船舶の窓(船用丸窓強化ガラスを除く),する強化ガラスについて規定する。
Tempered glass
This part of ISO 14368 specifies dimensional requirements of the interface for the assembly to the case by adhesive or using a gasket for round-shaped mineral and sapphire watch-glasses.
Mineral and sapphire watch-glasses - Assembly to the case by adhesive or using a gasket
This part of ISO 14368 specifies dimensional requirements of the interface for the assembly to the case by adhesive or using a gasket for round-shaped mineral and sapphire watch-glasses.
Mineral and sapphire watch-glases - Part 2: Assembly to the case by adhesive or using a gasket
1.1 This test method covers procedures for using gas chromatographs to determine the concentration of argon gas in the space between the panes of sealed insulating glass.1.2 This test method is not applicable to insulating glass units containing open capillary/breather tubes.1.3 The values stated in metric (SI) units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units using Gas Chromatography
Road vehicles-safety glazing materials-terminology
이 규격은 주로 탁상용이나 주방용으로 사용되는 내열 유리제 식기(이하 식기라 한다.)에 대
Heat resistant glass wares
This part of ISO 14368 specifies the dimensions and tolerances of mineral and sapphire watch-glasses. It is applicable to round, flat watch-glasses, typically of diameter 8 mm to 35 mm.
Mineral and sapphire watch-glasses - Dimensions and tolerances
The residue on ignition, which consists essentially of SiO2, is related to the silicon content of the silane and may be used to verify the composition of the silane. 1.1 This test method covers the determination of the residue on ignition of silanes of the type bis-(triethoxysilylpropyl)sulfane, or of admixtures of these silanes and solid carriers, such as carbon black, waxes, or organic polymers.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Silanes Used in Rubber Formulations (bis-(triethoxysilylpropyl)sulfanes): Residue on Ignition
This part of ISO 14368 specifies the dimensions and tolerances of mineral and sapphire watch-glasses. It is applicable to round, flat watch-glasses, typically of diameter 8 mm to 35 mm.
Mineral and sapphire watch-glasses - Part 1: Dimensions and tolerances
1.1 This specification covers chemical resistant, low expansion, Type I, borosilicate glass, Class A (see Specification E438), used to manufacture corrosion-resistant pipe and fittings for drain, waste, and vent service. 1.2 The pipe and fittings covered by the specification are intended for chemical resistant service above and below grade under gravity flow or vacuum conditions. 1.3 The pipe and fittings shall have beaded or plain ends.
Standard Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications
1.1 This specification covers chemically resistant, low expansion, Type I, borosilicate glass, Class A (see Specification E438), used to manufacture corrosion-resistant pipe and fittings for drain, waste, and vent service. 1.2 The pipe and fittings covered by the specification are intended for chemical resistant service above and below grade under gravity flow or vacuum conditions. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The pipe and fittings shall have beaded or plain ends.
Standard Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications
1.1 This specification covers chemical resistant, low expansion, Type I, borosilicate glass, Class A (see Specification E438), used to manufacture corrosion-resistant pipe and fittings for drain, waste, and vent service. 1.2 The pipe and fittings covered by the specification are intended for chemical resistant service above and below grade under gravity flow or vacuum conditions. 1.3 The pipe and fittings shall have beaded or plain ends.
Standard Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号