Q53 特殊炭素材料 标准查询与下载

YB/T 4587-2017 单晶炉用炭/炭复合材料发热体

Carbon/carbon composite heating element for single crystal furnace

YB/T 4588-2017 单晶炉用板状结构炭/炭复合材料

Plate structure carbon/carbon composite materials for single crystal furnaces

GOST 33599-2015 碳纤维. 高模量碳纤维密度的测定

Carbon fiber. Determination of density of high-modulus carbon fibers

GOST 33598-2015 碳纤维. 碳纤维抗热氧化的测定

Carbon fiber. Determination of thermal oxidative resistance of carbon fibers

PNST 63-2015 多壁碳纳米管材料. 规格

Materials from multiwall carbon nanotubes. Specifications

GOST R ISO 13931-2015 碳纤维. 体积电阻率的测定方法

Carbon fibre. Methods for determination of volume resistivity

PNST 34-2015 多层石墨烯. 规格

Multiplayer graphene. Specifications

BS ISO 13931:2013 碳纤维.体积电阻率测定

Carbon fibre. Determination of volume resistivity

JIS R 7608:2007 碳纤维.树脂浸渍纱拉伸性能的测定

この規格は，樹脂含浸ヤーンを用いた炭本繊維の引張強さ，引張弾性率及び最大荷重時の伸びの測定方法について規定する。この試験方法は，複合材料中の強化繊維としての炭素繊維(連続繊維及びステープルファイバー)へも適用可能である。

Carbon fibre -- Determination of tensile properties of resin-impregnated yarn

JIS R 7601 AMD 1:2006 碳素纤维的试验方法（修改件1）

JIS R 7601:1986を，次のように改正する。

Testing methods for carbon fibers (Amendment 1)

DIN EN ISO 10618:2004 碳纤维.树脂浸渍纱拉伸性能的测定

Carbon fibre - Determination of tensile properties of resin-impregnated yarn (ISO 10618:2004); German version EN ISO 10618:2004

BS EN ISO 10548:2003 碳纤维.胶料含量的测定

ISO 10548 specifies test methods for the determination of the size content of carbon fibre yarn. It is applicable to continuous-filament yarns and staple-fibre yarns.

Carbon fibre - Determination of size content

ASTM D5817-03a 试验用大颗粒、准圆度混合、干燥碳黑样品的标准实施规程

Several test methods for carbon black require the reduction in sample size or the blending of the test sample to reduce the variation of the measured characteristic. Other factors being equal, larger samples will tend to be more representative of the total supply. This practice provides procedures for reducing the large sample obtained from the bag and bulk sampling practices to a convenient size for conducting a number of tests to describe the material and measure its quality in such a manner that the smaller portion is most likely to be a representation of the bulk sample. Failure to follow the procedures in this practice could result in providing a nonrepresentative sample to be used in subsequent testing. Individual test methods provide for minimum amounts of material to be tested. Test Method A, Reduction of Sample Size, is typically used to obtain an aliquot from a large sample, splitting a black into two or more equal portions, or reducing a blended black from Test Method B to a specified sample size. The final sample is always smaller than the original sample and would not be considered to be a “well blended” sample. Test Method B, Blending of Carbon Black, is typically used to prepare a homogeneous sample. The homogeneous sample may be used for several tests (see Note 3) or may be reduced in size by Test Method A. The final sample size is the same as the original. When a sample is to be blended and reduced, the sample should be blended (Test Method B) before reduction (Test Method A). The blending and reduction must be done before the sample is dried (Test Method C).1.1 This practice describes the procedure for blending of pelleted carbon black, the procedure for the reduction of gross samples of pelleted carbon black to the appropriate size for testing and the preparation of the sample for testing. These techniques are intended to minimize variations in measured characteristics between test samples. Standard terminology relating to carbon black samples is found in Terminology D 3053.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black, Pelleted8212;Reduction, Blending, and Drying of Gross Samples for Testing

ASTM D5817-03 试验用大颗粒、准圆度混合、干燥碳黑样品的标准实施规程

1.1 This practice describes the procedure for blending of pelleted carbon black, the procedure for the reduction of gross samples of pelleted carbon black to the appropriate size for testing and the preparation of the sample for testing. These techniques are intended to minimize variations in measured characteristics between test samples. Standard terminology relating to carbon black samples is found in Terminology D 3053.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black, Pelleted-Reduction, Blending, and Drying of Gross Samples for Testing

ISO 10119:2002 碳纤维密度的测定

This International Standard specifies three methods for the determination of the density of carbon fibre yarn: — method A: liquid-displacement method; — method B: sink/float method; — method C: density-gradient column method. Method C is the reference method.

Carbon fibre - Determination of density

JIS R 7603:1999 碳纤维.密度测定

この規格はサィジング剤を除去Lた炭素繊維の密度を測定する4方法について規定する。

Carbon fiber -- Determination of density

DIN EN ISO 13002:1999 碳纤维.长丝纱的命名体系

The document establishes a system of designation for filament yarns of carbon fibre which may be used as the basis for specifications.

Carbon fibre - Designation system for filament yarns (ISO 13002:1998); German version EN ISO 13002:1998

NF T25-102*NF ISO 11566:1997 碳纤维.单丝试样抗拉性能的测定

Carbon fibre. Determination of the tensile properties of single-filament specimens.

BS ISO 11566:1996 碳纤维.单丝样品抗拉性能的测定

Describes a method of test for the determination of the tensile properties of a single-filament specimen. Applicable to single filaments of carbon fibres, taken from multifilament yarns, woven fabrics, braids and related products.

Carbon fibre - Determination of the tensile properties of single-filament specimens

NF T25-105:1996 塑料.词汇.补充件5:与碳纤维相关的术语

Plastics. Vocabulary. Amendment 5 : terms relating to carbon fibre.