Q87 园林动植物及其器械 标准查询与下载

ASTM D6818-02 草皮加强网基本拉伸特性的标准试验方法

The strip test in this test method is considered satisfactory for acceptance testing of commercial shipments of Turf Reinforcement Mats since the method has been used extensively in the trade for acceptance testing. 5.1.1 In case of disagreement arising from differences in reported test values when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimen which are as homogeneous as possible and are from a lot of material of the type in question. The test specimen should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Studentrsquo;t-test for unpaired data and an acceptable probability level chosen by the two parties before testing is begun. If bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future results in the light of the known bias.1.1 This test method covers strip test procedures for determining the tensile properties of Turf Reinforcement Mats (TRM).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.1.3 This standard does not apply to TRM''s made of composite materials where the component providing the reinforcement cannot be tested for tensile strength with the procedure herein described. In this case, the established ASTM testing method, which is most appropriate for that material, shall be used instead.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Ultimate Tensile Properties of Turf Reinforcement Mats

BS ISO 3767-1:1998+A2:2012 拖拉机,农业和林业动力草坪和花园设备.工作人员操作设备和其它显示装置用符号.通用符号

Tractors, machinery for agriculture and forestry, powered lawn and garden equipment. Symbols for operator controls and other displays. Common symbols

BS EN 836:1997+A4:2011 园林设备.电动割草机.安全性

Garden equipment. Powered lawnmowers. Safety

NF U15-460/A2:1997 NF EN 774-1996的修改件2

Garden equipment - Hand held, integrally powered hedge trimmers - Safety.

BS EN 786:1996+A2:2009 园艺设备.电动步行手扶剪草机和草地修边机.机械的安全性

This European Standard specifies mechanical safety requirements and testing for the design and construction of electrically powered walk-behind and hand-held lawn trimmers and lawn edge trimmers, with cutting element(s) of non-metallic filament line or freely pivoting non-metallic cutter(s) with a kinetic energy of not more that 10 J each, and used by a standing operator primarily for cutting grass. It describes methods for the elimination or reduction of hazards arising from their use. In addition, it specifies the type of information to be provided by the manufacturer on safe working practices. This standard is not applicable to: a) Scissor type or lawn trimmers and lawn edge trimmers with cutting means other than those described above; b) Self-propelled lawn trimmers or lawn edge trimmers; c) Lawn trimmers or lawn edge trimmers which do not have a distance of at least 600 mm between the cutting means control and the cutting head. The electrical aspects of electrically powered lawn trimmers and lawn edge trimmers are not covered by this standard. The list of significant hazards dealt with in this standard is given in annex A. Annex A also indicates the hazards which have not been dealt with. Environmental aspects have not been considered in this standard. This European Standard applies primarily to machines which are manufactured after the date of issue of this standard. NOTE The method of calculating the kinetic energy for the purposes of this standard is given in annex B.

Garden equipment - Electrically powered walk-behind and hand-held lawn trimmers and lawn edge trimmers - Mechanical safety

NF U15-220:1996 农林机械安全性要求.电动步行手扶剪草机和草地修边机

Garden equipment. Electrically powered walk-behind and hand-held lawn trimmers and lawn edge trimmers. Mechanical safety.

ASTM D5883-96(2008) 园林设计及其有关用途用上层土中矿物质修正值、旋转窑生产的空心油岩、粘土或石片用标准指南

When physically evaluating a soil, relative to its suitability to support plant growth (primarily grasses), tests must be performed to determine the presence and amount of solid matter (organic and inorganic) compatibility that can determine potential air-void content and water-holding ability, and finally, deleterious materials. Typical general ranges of soil content for suitable topsoils are presented in Specification D 5268. It should be recognized, however, that in some geographic regions, concurrence with the values in the referenced table would be difficult. In such situations, locally acceptable specifications need to be developed.1.1 This guide covers the material characteristics, physical requirements, and sampling appropriate for the designation of the material as a mineral amendment. 1.2 The presence in the topsoil of the correct nutrient and pH level is necessary for healthy plant growth. This guide does not, however, cover a determination of the nutrients, nor their availability. Note 18212;The nutrient content of topsoil is important and the chemicals usually evaluated are nitrogen, phosphate, and potassium. Nutrient deficiencies may be corrected by using fertilizers. Excess soluble salts should be examined as to their desirability. The acidity or alkalinity of the soil is also important. Excess acidity may be corrected by the application of lime dust. Excess alkalinity may be corrected by the application of sulfur or other suitable acidifying compounds. The latter item, in addition to lowering pH, also could be considered as an aggregate when considering the particle size distribution. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project''s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.

Standard Guide for Use of Rotary Kiln Produced Expanded Shale, Clay or Slate (ESCS) as a Mineral Amendment in Topsoil Used for Landscaping and Related Purposes

SAE J1175-1985 小型发动机动力设备用在场人员的声级测试规程

This SAE Recommended Practice establishes the instrumentation and procedure to be used in measuring the bystandard sound level of engine powered equipment under 15 kW (20 bhp) typical of their normal operation. it is intended to include equipment such as lawn mowers, snow blowers, and tillers. It is not intended to include equipment designed primarily for operation on highways or within factories and buildings, or vehicles such as motorcycles, snowmobiles, and pleasure motorboats that are covered by other SAE Standards or Recommended Practices. This procedure does not cover chain saws. The SAE Recommended Practice may also be used when measuring the bystander sound level on similar equipment powered by electricity or other power sources.

Bystander Sound Level Measurement Procedure for Small Engine powered equipment

SAE J1174-1985 小型发动机动力设备用操作员耳朵（所受噪声）声级的测试规程

This SAE Recommended Practice establishes the instrumentation and procedure to be used in measuring the operator ear sound level for engine powered equipment under 15 kW (20 bhp). The sound levels obtained by using this procedure are representative of the sound levels generated by the equipment under typical operating conditions. It is intended to include equipment such as lawn mowers, snow blowers, and tillers. It is not intended to include equipment designed primarily for operation on highways or within factories or buildings, or vehicles such as motorcycle, snowmobiles, and pleasure motorboats that are covered by other SAE Standard or Recommended Practice. This procedure does not cover chain saws. This SAE Recommended Practice may also be used when measuring the operator ear sound level of similar equipment powered by electricity or other power sources.

Operator Ear Sound Level Measurement Procedure for Small engine powered Equipment

BS EN 62841-2-1:2018+A11:2019 手持式电动操作工具, 移动式工具以及草坪和园艺机械. 安全性. 手持式刨床的特殊要求

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery. Safety. Particular requirements for hand-held planers

BS EN ISO 5395-2:2013+A2:2017 园林设备. 燃烧引擎动力式剪草机的安全性要求. 步行操纵的剪草机

Garden equipment. Safety requirements for combustion-engine-powered lawnmowers. Pedestrian-controlled lawnmowers

BS EN ISO 5395-1:2013+A1:2018 园林设备. 燃烧引擎动力式剪草机的安全性要求. 步行操纵的剪草机

Garden equipment. Safety requirements for combustion-engine-powered lawnmowers. Pedestrian-controlled lawnmowers