T06 工艺与工装 标准查询与下载

ASTM D5066-91(2005) 在喷涂汽车涂料的生产条件下测定转换效率的试验方法

This test method is specifically directed at the spray painting of automobile car and light duty truck bodies. The general principles are applicable to the painting of other automotive parts. This test method may also be used to measure transfer efficiency in full-sized painting facilities simulating production conditions and operations.1.1 This test method covers procedures for determination of the transfer efficiency (using a weight method) under production conditions for in-plant spray application of automotive paints as outlined in Section 18 of EPA 450/3-88-018.1.2 The transfer efficiency is calculated from the weight of the paint solids sprayed and that deposited on the painted part. The recommended approach involves painting the part directly. Also described is an alternative approach for painting parts covered with aluminum foil.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 10.1.8.1.

Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints-Weight Basis

QCn 29018-1991 汽车碳氮共渗齿轮金相检验

本标准规定了钢制汽车碳氮共渗齿轮的金相组织、有效硬化层深度、表面及心部硬度的含义和检测方法。 　　本标准适用于有效硬化层深度大于0.3mm的齿轮。 　　本标准用于完成所有热处理工序后的齿轮质量检验。

Metallographic inspection of automobile carbonitriding gear

SAE J811-1981 表面滚压和其他给金属预加应力的方法

This SAE Information Report covers applications of mechanical prestressing, improving fatigue resistance, theory of surface rolling for fatigue improvement, calculations for the surface rolling process, tooling for surface rolling, control and inspection, effect of surface rolling on properties other than fatigue, and other methods for mechanical prestressing.

Surface Rolling and Other Methods for Mechanical Prestressing of Metals

SAE J792A-1968 喷抛处理SAE指南

This manual on blast cleaning is a companion to the SAE manual on shot Peening. It is intended to help engineers, management, and shop personnel to increase their knowledge of the process. The information contained herein has been submitted and edited by a group that has had extensive and varied experience with blast cleaning and whose recommendations merit consideration.

SAE Manual on Blast Cleaning

SAE J449A-1963 表面纹理控制

SAE J448, Surface Texture, has been set up for precision reference specimens using a controlled surface profile to obtain reproducible roughness values. These specimens are for instrument calibration. appropriate symbols for roughness, waviness, and lay have also been standardized (ASA B46.1-1962 and SAE J448). For production control, especially from one geographical location to another, means are required to facilitate the inspection of surface characteristics called for by specifications which include not only roughness but profile waviness and lay. In order to integrate the requirements of the designer with the actual production of surfaces, a second grade of control standards must be adopted which will be functional in nature for the specific product being manufactured. These control standards may be Calibrated pilot specimens (actual parts with satisfactory texture) or Roughness comparison Specimens (ASA B46.1-1962). This SAE Recommended practice describes the usage of these control standards.

Surface Texture Control

SAE J473A-1962 焊合

The choice of the type and grade of solder for any specific purpose depend on the materials to be joined and the method of applying. those with higher amounts of tin usually wet and bond more readily and have a narrower semi- molten range than lower amounts of tin. For strictly economic reasons, it is recommended that the grade of solder metal be selected that contains least amount of tin required to give suitable flowing and adhesive qualities for application.

Solders

SAE J493-1961 杆端和U形夹销

Material--SAE 1010 or SAE 1111 steel or equivalent. Clevis pins shall be supplied either soft or cyanide hardened as specified. Clevis pins must be free from burrs, loose scale, sharp edges, and all other defects that might affect their serviceability. General tolerances for all dimensions are plus or minus 0.010 unless otherwise specified.

Rod Ends and Clevis Pins