T12 机体与运动件 标准查询与下载

QC/T 275-2008 汽车发动机镶耐磨圈活塞金相检验

本标准规定了汽车发动机镶耐磨圈活塞（以下简称镶圈活塞）的金相组织级别、检验及评定。 本标准适用于气缸直径为200mm以下的汽车发动机共晶铝硅合金镶圈活塞。

Metallographic examination of piston with ringcarrier for automotive engines

ISO 6621-1:2007 内燃机.活塞环.第1部分:词汇

This part of ISO 6621 defines the most commonly used terms for piston rings. These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. The terms and definitions in this part of ISO 6621 apply to piston rings for reciprocating internal combustion engines. They may also be used for piston rings of compressors working under analogous conditions. NOTE 1 Further terms and definitions covering measuring principles are given in ISO 6621-2. NOTE 2 In addition to terms given in the three official ISO languages (English, French and Russian), this part of ISO 6621 gives the equivalent terms in the German, Spanish, Portuguese, Italian and Japanese languages. However, only the terms given in the official languages can be considered as ISO terms. These have been included at the request of Technical Committee ISO/TC 22 and are published under the responsibility of the member bodies for Germany (DIN), Spain (AENOR), Portugal (IPQ), Italy (UNI) and Japan (JIS).

Internal combustion engines - Piston rings - Part 1: Vocabulary

GM 9984141-2007 用于外饰部件热塑性聚烯烃漆膜的模压漆膜

Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprüfungen tragt der Liefera ie Verantwortung dafür, daß die gelieferte Ware die Opel-Zeichnungsvorschriften erfüllt. Ein Prüfbericht mit zahlenmaßigen Ergebnissen aus Prufungen der Lieferung

Moldable Paint Film on Thermoplastic Polyolefin (TPO) Film For Exterior Parts Revision C

NF R15-509:2005 皮带传动.汽车工业用窄V带.疲劳试验

Belt drives - Narrow V-belts for the automotive industry - Fatigue test.

QC/T 737-2005 轿车发动机铸铁活塞环技术条件

本标准规定了轿车发电机整体铸铁活塞环(不包含组合油环)的技术要求、试验方法、检验规则、标志、包装和储存等。 本标准适用于汽缸直径小于或等于100mm的轿车用发电机铸铁活塞环。

Specifications for cast-iron piston ring of passenger car engine

QC/T 736-2005 轿车发动机钢带组合油环技术条件

本标准规定了轿车发动机钢带组合油环的术语、技术要求、监测方法、检验规则、标志、包装和贮存。 　　本标准适用于公称直径不大于100mm的轿车发动机钢带环。

Specifications for steel belt combined oil ring of car engine

ISO 16246:2005 道路车辆.带平座和14 mm六角的M12 x 1.25火花塞及其气缸盖

This International Standard specifies the characteristics of M12×1,25 spark-plugs with flat seating and 14 mm hexagon and their cylinder head housings, used with spark-ignition engines in road vehicles.

Road vehicles - M12 x 1,25 spark-plugs with flat seating and 14 mm hexagon and their cylinder head housing

QC/T 481-2005 汽车发动机曲轴技术条件

本标准规定了汽车发动机曲轴的技术要求、试验方法、检验规则和标志、包装、运输及贮存。 本标准适用于汽车发动机曲轴。

Specifications of crankshaft for vehicle engine

BS ISO 18669-2:2005 内燃机.活塞销.检验测量原理

ISO 18669-2:2004 defines the measuring principles to be used for measuring piston pins; it applies to piston pins from 8 mm up to and including 100 mm outside diameter for reciprocating internal combustion engines and compressors. In certain applications, except road vehicles, and provided that mutual agreement is made between the purchaser and the manufacturer, ISO 18669-2:2004 may be used with suitable modifications.

Internal combustion engines - Pistons pins - Inspection measuring principles

GM 9984263-2004 照明设备的金属化处理

Stoff zum Überziehen von Sitzen und Rückenlehnen. Fabric for covering of seats and seat backs.

Metalized Finish for Lighting Applications Revision D

SAE J1334-2003 液压缸的完整性测试

Applies to hydraulic cylinders which are components of self-propelled work machines defined in SAE J 1116. To provide a laboratory method for determining the structural integrity of a double acting hydraulic cylinder. General seal performance is monitored during the cylinder cycle test.

Hydraulic Cylinder Integrity Test

GM 9984179-2003 外饰部件,丙烯腈丁二烯苯乙烯漆膜的可模压漆膜

Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein

Moldable Paint Film on Acrylonitrile Butadiene Styrene (ABS) Film For Exterior Parts Revision C

ISO 5287:2003 皮带传动.汽车工业用窄V带.疲劳试验

This International Standard specifies a fatigue test for the quality control of narrow V-belts (sections AV 10 and AV 13) intended for driving the auxiliaries of internal combustion engines used for automotive purposes. NOTE The dimensional characteristics of these belts and of the corresponding pulleys are the subject of ISO 2790.

Belt drives - Narrow V-belts drives for the automotive industry - Fatigue test

GM 9984259-2003 9984258的清漆成分

Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein

Clearcoat Component of 9984258 Revision A

GM 9984242-2003 9984198的清漆成分

Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein

Clearcoat Component of 9984198 Revision A

GM 9984168-2002 透明涂料(漆膜)

This specification covers the requirements depending on quality of this upholstery fabric. The general minimum requirements shall be tested on principle to TM 110000.

Transit Coating (Film) Revision A [Replaced: HOLDEN HN 1684, HOLDEN HN 1685]

SAE J393-2001 商用车辆的型号轮子,轮毂和轮辋

This SAE Recommended Practice establishes uniform engineering nomenclature for wheels, hubs, rims, and their components used in truck, bus, and trailer applications. This nomenclature and accompanying drawings are intended to define fundamental truck wheel, hub, and rim designs. The International Standard (ISO) nomenclature is shown in parentheses when different than SAE J393.

Nomenclature Wheels, Hubs, and Rims for Commercial Vehicles

SAE J851-2001 商用车辆的垫圈间箍和可拆卸轮辋可拆卸轮辋的尺寸轮

This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rim, rim spacer, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.

Dimensions Wheels for Demountable Rims, Demountable Rims and Spacer Bands Commercial Vehicles

ISO 9259:1991/Amd 1:2001 乘用车 风挡玻璃刮刷系统 刷臂与刮水片的连接 修改1

This is Amendment 1 to ISO 9259-1991 (Passenger cars — Windscreen wiper systems — Wiper arm-to-blade connections)

Passenger cars - Windscreen wiper systems - Wiper arm-to-blade connections; Amendment 1

QC/T 637-2000 汽车发动机曲轴弯曲疲劳强度试验方法

本标准规定了汽车发动机曲轴曲拐试样的台架疲劳试验方法、数据处理方法和试验精度要求。 　　本标准适用于下列情形：曲轴疲劳强度评估试验、新设计、变更工艺、变更材料、货源鉴定、产品质量抽检及其它认为肯能引起疲劳强度显著变化等情况。

Automobile engine crankshaft bending fatigue strength test method