T31 紧固件 标准查询与下载

JASO F121-2007 汽车部件.带轴环的平头螺钉

Automotive parts-Pan head screws with collar

DLA MS33736 REV D (1)-2006 制动接线柱的螺丝扣组装

Prior to safetying, both threaded terminals shall be threaded an equal distance into the turnbuckle body and shall be threaded to a depth such that not more than three full threads of any terminal are exposed outside the body.

TURNBUCKLE ASSEMBLIES, CLIP LOCKING OF

DLA MS33736 REV D ADMIN NOTICE 1-2005 制动接线柱的螺丝扣组装

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http://assist.daps.dla.mil/.

TURNBUCKLE ASSEMBLIES, CLIP LOCKING OF

DLA MS21256 REV G ADMIN NOTICE 1-2005 螺丝扣制动接线柱

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http://assist.daps.dla.mil/.

CLIP, LOCKING, TURNBUCKLE

DLA MS21251 REV M (1)-2005 制动接线柱螺丝扣体

This specification is approved for use by all Departments and Agencies of the Department of Defense.

TURNBUCKLE BODY, CLIP LOCKING

BS EN 12195-1:2003 道路车辆上的装载物固定组件.安全.捆绑力的计算

This Part of EN 12195 specifies acceleration coefficients for surface transport. It also gives methods of calculation of lashing forces acting on goods on load carriers, lorries, trailers and swap bodies, either on road, on vessels or by rail and/or combinations thereof for different types of load and different types of lashing. It excludes the hump shunting during railway transport (web lashings see EN 12195-2, lashing chains see EN 12195-3, wire lashing ropes see prEN 12195-4). The lashing forces to be chosen for calculation in this EN 12195-1 are static forces produced by tensioning of lashings and dynamic forces, which act on the lashing as a reaction of the load movements. Instructions for the application of calculations are also specified.

Load restraint assemblies on road vehicles - Safety - Calculation of lashing forces

QC/T 713-2004 塑料(尼龙)用自攻螺钉螺纹

本标准规定了螺纹规格为NST 3～NST 7自攻螺钉螺纹的形状、尺寸、螺钉末端及攻丝前塑料(尼龙)底孔直径。 　　本标准适用于拧入塑料(尼龙)底孔的自攻螺钉螺纹。

Tapping screws thread for plastic(nylon)

QC/T 712-2004 汽车安全带装置固定连接用焊接螺母

本标准规定了英制统一螺纹规格为0.4375-20UNF-2B(即螺纹公称直径为7/16英寸)的焊接螺母的型式、尺寸和技术条件，包括六角及方形两种型式。 　　本标准适用于汽车安全带装置固定连接用焊接螺母。

Weld nuts for fixing the safety belt devices of vehicle

QC/T 715-2004 汽车用螺纹连接副摩擦系数的测试方法

本标准规定了汽车用螺纹连接副摩擦系数的测试方法。 　　本标准适用于采用专用自动操作试验装置，对汽车用螺栓—螺母螺纹连接副摩擦系数进行测试。

Measuring method for friction coefficient of screw thread pair of automobiles

SAE J1835-2004 可卸轮缘车轮用紧固件金属件

This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degree bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. his document is divided into two sections. Section 1 establishes the practice for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.

Fastener Hardware for Wheels for Demountable Rims

SAE J2655-2003 垫圈和缩减垫圈的紧固件零件标准(英制尺寸规格)

This SAE Part Standard covers selected inch dimensioned washers and lock washers manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever washers of the covered materials are used. This standard permits the washers to be identified and ordered by a part of identifying number (PIN) as defined in this standard. The purpose of this document is to assist the designer and other personnel in providing requirements and part or identifying numbers for the most commonly used washers and lock washers. A part or identification number (PIN) is normally required for all military applications and provides a useful means of communicating washer and lock washer requirements to suppliers and manufacturers in a very succinct manner.

Fastener Part StandardWashers and Lockwashers (Inch Dimensioned)

DLA MS21256 REV G-2003 螺丝扣制动接线柱

The part or identifying number (PIN) consists of the letters MS, the specification sheetnumber, and a dash number taken from table I.

CLIP, LOCKING, TURNBUCKLE

SAE J2606-2003 用在发动机,变速器和轴上的排放塞和加注塞

Drain and fill plugs used on engines, transmissions, transfer cases and front and rear drive axles for class 5 - 8 vehicles. The purpose of this SAE Recommended Practice is to establish and maintain a common plug, for various bus and truck powertrain components, among the various manufacturers. This will allow OEM manufacturing facilities and service outlets to utilize common plugs and common tools for oil fill and drain operations.

Drain and Fill Plug for use on Engines, Transmissions, and Axles

SAE J2485-2003 机用螺钉螺母(公制和英制)的紧固件部分标准

This SAE Part Standard covers selected machine screw nuts manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This document covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document. The purpose of this document is to assist the designer and other personnel in providing requirements and part identifying numbers for the most commonly used machine screw nuts. A part or identification number is normally required for all military applications and provides a useful means of communicating fastener requirements to suppliers and manufacturers in a very succinct manner.

Fastener Part Standard - Machine Screw Nuts (Metric and Inch)

SAE J2337-2-2002 带ISO 261标准螺纹和O形密封的端口,螺柱端和插头用液压动力和高压连接件.第2部分:螺柱端要求,尺寸规格,设计和试验方法

This part of SAE J 2337 specifies dimensions, design, and performance requirements for eight connectors using a conical seal to insure leak proof performance with a design factor of 4 to 1. These connectors are intended for general and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These connectors are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa vacuum to the working pressures shown in Table 1. Since many factors influence the pressure at which hydraulic systems will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to ensure that the required performance levels are met.CAUTION—For use of these connectors in conditions outside the pressure and temperature limits specified, contact the manufacturer.

Connections for Fluid Power and High Pressure Use Ports, Stud Ends, and Plugs with ISO 261 Threads and O-Ring SealingPart 2: Stud End Requirements, Dimensions, Design, and Test Methods

SAE J2484-2002 机用螺钉的紧固件部分标准

This SAE Part Standard covers selected machine screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document. The purpose of this document is to assist the designer and other personnel in providing requirements and part identifying numbers for the most commonly used machine screws for ship systems and equipment. A part or identification number is normally required for all military applications and provides a useful means of communicating fastener requirements to suppliers and manufacturers in a very succinct manner.

Fastener Part StandardMachine Screws

QC/T 638-2000 密封垫圈

Gasket

QC/T 616-1999 C型通孔式嵌装塑料螺母

本标准规定了C型通孔式嵌装塑料螺母。 　　本标准适用于自攻螺钉联接用的嵌装塑料螺母。

C-type through-hole embedded plastic nut

QC/T 340-1999 六角法兰承面带齿螺栓

本标准规定了螺纹规格为M6～M16和M8×1～M16×1.5六角法兰承面带齿螺栓的型式、尺寸和技术条件。

Hexagon flange face toothed bolts

QC/T 346-1999 塑料堵塞

本标准规定了A型和B型塑料堵塞。 　　本标准适用于汽车上用来堵光孔和螺纹孔的堵塞。

plastic plug