T34 其他 标准查询与下载

WJ/Z 432.47-2007 装甲车辆柴油机通用件 第47部分：起动阀

General Parts for Diesel Engines for Armored Vehicles Part 47: Starting Valves

SAE J2384-2006 空气干燥剂试验规程

This SAE Recommended Practice establishes uniform Test Procedures for desiccant Air Dryers used in vehicles with compressed air systems per SAE J2383. Continuous flow desiccant Air Dryers are excluded from the scope of this document.

Air Dryer Test Procedure

SAE J2301-2005 万用接头外叉连接

This document specifies the main dimensions and tolerances, which affect interchangeability between end yoke earwork for the most common North American used universal joints. Dimensions and tolerances of the mating universal joints are left to the discretion of the universal joint manufacturers. The term "Earwork" refers to the configuration and geometry defining end yoke connections directly providedfor universal joint cross attachment of drivelines. Earwork for certain styles of universal joint connections and flange connections have for a long time been proprietary to certain manufacturers. Over years of usage, proprietary rights have expired and the industry, as a whole, has used these earworks as standard. In an effort to tabulate some of the long established practices, the following SAE Recommended Practice has been compiled. Manufacturers do from time to time, as the need arises, change tolerances or fits to better enhance component performance. This document has been prepared as a reference, and is a snap shot of current technology. The half round (strap connection), full round (retainer plate type connection) and wing type connection are covered in this document. For an understanding of these end yoke styles, please refer to SAE J901. There are earwork forms that still are proprietary and are not covered by this document.

Universal Joint End Yoke Connection (Earwork)

SAE J2051-2005 机动车制造用底盘安装的四通空气阀门的合格鉴定

This SAE Recommended Practice describes the requirements necessary for four-way subbase mounted, directional air-control valves to be used in automotive manufacturing applications. It includes minimum performance, operation, and physical requirements to qualify the valves for service in automotive manufacturing applications. Included are spool, poppet, and sliding disc types of air valves for pressures in a range of vacuum to 1034 Kpa (150 lb/in2) gage, and temperatures from -18 to 60 degrees C (0 to 140 degrees F).

Qualifications for Four-Way Subbase Mounted Air Valves for automotive manufacturing Applications

NF R99-031:2004 轮胎气门.ISO芯室1、2和3号

Tyre valves - ISO core chambers No. 1, No. 2 and No. 3.

DIN EN 12195-4:2004 道路车辆上的装载物固定装置.安全.第4部分:捆绑用钢丝绳

This standard specifies the requirements related to safety for lashing steel wire ropes for use with road vehicles.

Load restraint assemblies on road vehicles - Safety - Part 4: Lashing steel wire ropes; German version EN 12195-4:2003

QC/T 699-2004 车用起重尾板

本标准规定了车用起重尾板的术语和定义、型号、基本参数、要求、试验方法、检验规则、标志、说明书、包装、运输和贮存。 　　本标准适用于安装在车辆尾部的液压式车用起重尾板(简称尾板)。

Tail-lift for vehicle

SAE J1341-2003 货车和公共汽车用液压泵耗能量测量的试验方法

The testing technique outlined in this SAE Recommended practice was developed as part of an overall program for testing and evaluating fuel consumption of heavy-duty trucks and buses. The technique outlined in this document provides a general description of the type of equipment and facility which is necessary to determine the power consumption of these engine-driven components. It is recommended that the specific operating condition suggested throughout the test be carefully reviewed on the basis of actual data obtained on the specific vehicle operation. This document covers evaluation techniques for determining the power consumption characteristics of hydraulic pumps used on heavy-duty trucks and buses. The purpose of this document is to expand on the scope of the existing SAE J745. All of the specifications and apparatus utilized in that document for construction and industrial machinery can be utilized in this procedure. Information presented in the manner outlined as follows can be used to evaluate the hydraulic power requirements of fixed or variable-displacement pumps after the vehicle duty cycle has been determined.

Test Method for Measuring Power Consumption of Hydraulic Pumps for Trucks and Buses

DIN EN 12195-3:2001 道路车辆装载物系固装置.安全性.第3部分:捆绑链

Load restraint assemblies on road vehicles - Safety - Part 3: Lashing chains; German version EN 12195-3:2001

BS EN 12195-3:2001 道路车辆上物件的系固用具.安全.捆绑链

This Part of EN 12195 specifies safety requirements for lashing chains and lashing combinations with chain for the safe surface transport of goods on load carriers, e.g. trucks and trailers which are used on roads or located on vessels or on rail waggons and/or combinations thereof. The standard includes only tensioning devices to be hand driven with a maximum handforce of 500 N. It does not give requirements for multi-purpose lever blocks other than to the type of fine tolerance chain and the additional marking of the maximum hand-operating force . This Part of EN 12195 deals with hazards which could occur when lashing chains are in use as intended and under conditions foreseen by the manufacturer (see clause 4 and Annex A).

Load restraint assemblies on road vehicles - Safety - Lashing chains

DIN EN 12195-2:2001 道路车辆上的装载物固定装置.安全.第2部分:人造纤维制成的捆绑网

The document specifies the following: safety requirements for web lashing made from man-made fibres with flat woven webbings for multiple use and of lashing combinations with webbings for the safe surface transport of goods on road vehicles, methods for testing of web lashing for securing of loads, deals with the significant hazards which could occur when web lashings are in use as intended, includes composite load restraint assemblies also for the same purpose as above.#,,#

Load restraint assemblies on road vehicles - Safety - Part 2: Web lashing made from man-made fibres; German version EN 12195-2:2000

BS EN 12195-2:2001 道路车辆的负载限动组件.安全性.人造纤维网绳

This Part of EN 12195 — specifies safety requirements for web lashing made from man-made fibres with flat woven webbings for multiple use and of lashing combinations with woven webbings for the safe surface transport of goods on road vehicles, e.g. trucks and trailers which are used on roads or located on vessels or on rail waggons and/or combinations thereof; — includes only tensioning devices to be hand driven with a maximum hand force of 500 N; — specifies methods for testing of web lashing for securing of loads; — deals with the significant hazards which could occur when web lashings are in use as intended and under conditions foreseen by the manufacturer (see clause 4 and Annex A); — includes composite load restraint assemblies also for the same purpose as above.

Load restraint assemblies on road vehicles - Safety - Web lashing made from man-made fibres

SAE J901-2000 万向接头和从动轴词汇集.术语.应用

The following definitions and illustrations are intended to establish common nomenclature and terminology for universal joints and driveshafts used in various driveline applications. In addition, useful guidelines are included for the application of universal joints and driveshafts. For more specific details, see universal Joint and driveshafts design manual, AE-7.

Universal Joints and driveshafts Nomenclature- Terminology- Application

QC/T 446-1999 鞍式牵引车牵引座

本标准适用于鞍式牵引车与半挂车之间机械联结的牵引座安装板。

Saddle tractor fifth wheel

QC/T 262-1999 汽车渗碳齿轮金相检验

本标准规定了汽车钢制渗碳齿轮金相组织，渗碳层有效层深度的含义及检测方法。 　　本标准适用于渗碳淬硬层有效深度大于0.3mm的汽车齿轮。 　　本标准用于齿轮在完成所有热处理工序后的质量检查。

Metallographic inspection of automobile carburized gear

WJ 1413-1998 装甲车辆随车随机工具及附件 木制件规范

Specifications for wooden parts of tools and accessories attached to armored vehicles

QC/T 236-1997 汽车内饰材料性能的试验方法

本标准规定了汽车内装饰纺织品、非制造布、皮革、塑料等材料的平方米质量、耐磨性、擦毛性、抗玻璃雾化性的试验方法。 　　本标准适用于测试汽车内装饰纺织品、非织造布、皮革、橡塑等材料的性能。

Test methods for the performance of automotive interior materials

QC/T 216-1996 汽车用地毯的性能要求和试验方法

本标准规定了汽车内饰用未成型的针刺地毯的技术要求及试验方法。 　　本标准适用于各种汽车内饰未成型的针刺地毯。

Performance requirements and test methods for automotive carpets

QC/T 217-1996 汽车用压力报警器

本标准规定了汽车用压力报警器的分类、型式、 基本参数、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 　　本标准适用于汽车用压力报警器。其它机动车用压力报警器也可参照执行。

Automotive pressure alarm

QC/T 207-1996 汽车用普通气弹簧

本标准规定了汽车用普通气弹簧的术语、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 　　本标准适用于汽车用各种规格的固定行程普通气弹簧，其他机械用气弹簧可参照采用。

Ordinary gas spring for automobile