T70 挂车综合 标准查询与下载

ASTM E2518-11 IV型(M923型5 t货运卡车/M1083型5 t中轻型装甲车(MTV)/M1082型5 t拖车)载货平板车车盖的标准规格

1.1 This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV CBC is a removable general purpose rigid wall enclosure that is mounted to the following model 5 ton cargo trucks: (1) the M923 Medium Tactical Vehicle (MTV) and (2) the M1083 MTV. It also can be mounted on the M1095 5 Ton MTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Cargo Bed Cover, Type IV (M923, 5 Ton Cargo Truck/M1083, 5 Ton Medium Tactical Vehicle (MTV)/ M1082, 5 Ton MTV Trailer)

JT/T 389-2010 厢式挂车技术条件

本标准规定了厢式挂车的技术要求、试验方法、检验规则、标志、包装、运输及储存。 本标准适用于货物运输的厢式半挂车、厢式牵引杆挂车和厢式中置轴挂车(以下简称“厢式挂车”)。

Specification for van trailers

JT/T 789-2010 道路甩挂运输车辆技术条件

本标准规定了牵引车、半挂车和总质量49 t 以下的半挂汽车列车的性能与装置。 本标准适用于甩挂运输的车辆。

Specification for swap trail transport of road vehicles

JT/T 316-2010 货运挂车产品质量检验评定方法

本标准规定了货运挂车产品质量检验的抽样、检验项目与检验方法，以及整车产品质量综合评定方法。 本标准适用于符合GB 1589要求的货运挂车的产品质量监督检验和企业内部质量控制,其他挂车产品的质量检验可参照执行。

Products quality inspection and evaluation method of freight trailer

SAE J2863-2010 汽车拖车拖行连接头

This SAE Standard provides the minimum requirements for Automotive or RV, 7 Position, Self Draining Trailer Tow Connector Interface. The procedures included within this specification are intended to cover the test methods, design, and performance requirements, of the electrical interface of the 7 position trailer tow connector in low voltage (0 to 20) road vehicle applications.

Automotive Trailer Tow Connector

KS R ISO 4927:2009 道路车辆.使用非石油基液压制动液的鼓式液压缸的弹性保护罩(最大工作温度120℃)

이 표준은 드럼식 휠 브레이크 실린더의 양 끝에 사용되는 성형 고무 부츠의 성능 시험에 대

Road vehicles－Elastomeric boots for cylinders for drum type hydraulic brake wheel cylinders using a non-petroleum base hydraulic brake fluid(Service temperature 120 ℃ maximum)

KS R ISO 4928:2009 道路车辆.使用非石油基液压制动液的液压制动系统液压缸的弹性罩皮碗和密封圈(最大工作温度120℃)

이 표준은 도로 차량의 유압 브레이크 장치에 사용되는 브레이크 컵과 실(seal)의 성능

Road vehicles－Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid(Service temperature 120 ℃ maximum)

KS R ISO 4930:2009 道路车辆.使用非石油基液压制动液的液压制动盘式液压缸的弹性密封垫(最大工作温度150℃)

이 표준은 도로용 차량의 디스크 브레이크 실린더에 사용하는 고무 실(seal)의 성능 시험

Road vehicles-Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid(Service temperature 150 ℃ maximum)

SAE J2377-2009 卡车牵引车及拖车牵引车空气供给试验规程

This SAE Recommended Practice (RP) provides test procedures for air braked trucks and truck-tractors used to tow single and multiple trailer combinations on highways. This RP is not intended for off-highway applications. This document provides a method of determining the capability of towing trucks and truck-tractors to supply compressed air to the reservoirs and parking brake chambers on towed vehicles.

Test Procedure for Air Supply of Truck-Tractors and Towing Trucks

VC 8027-2010 O2类和O3类车辆的强制规范

This specification covers the requirements for vehicles of category O3 and O4 designed or adapted for the conveyance of goods and for operation on a public road, including any category O3 and O4 vehicle not previously registered in South Africa. New vehi

Compulsory specification for vehicles of category O3 and O4

VC 8026-2010 O1类和O2类车辆(旅行拖车和轻型拖车)

This specification covers the requirements for vehicle models of categories O1 and O2 designed or adapted for operation on a public road at speeds greater than 40 kph, including new vehicle models and vehicle models that have not previously been register

Category O1 and O2 vehicles (caravans and light trailers)

SAE J2403-2008 中型/重型E/E系统诊断术语

This SAE Recommended Practice is applicable to all E/E systems on MD and HD vehicles. The terms defined are largely focused on compression-ignited and spark-ignited engines. Specific applications of this document include diagnostic, service and repair manuals, bulletins and updates, training manuals, repair data bases, under-hood emission labels, and emission certification applications. This document focuses on diagnostic terms, definitions, abbreviations, and acronyms applicable to E/E systems. It also covers mechanical systems which require definition. Nothing in this document should be construed as prohibiting the introduction of a term, abbreviation, or acronym not covered by this document. The use and appropriate updating of this document is strongly encouraged. Certain terms have already been in common use and are readily understood by manufacturers and technicians, but do not follow the methodology of this document. To preserve this understanding, these terms were included and have been identified with "historically acceptable common usage,' so they will not erroneously serve as a precedent in the construction of new names. These terms fall into three categories: a. Acronyms that do not logically fit the term. b. Acronyms existing at the component level, i.e., their terms contain the base word or noun that describes the generic item that is being further defined. c. Acronyms for terms that appear to contain the base word, but are frequently used as a modifier to another base word. (This use may possibly be thought of as following the methodology since the acronym is normally used as a modifier.)

Medium/Heavy-Duty E/E Systems Diagnosis Nomenclature

KS R ISO 4929:2008 道路车辆.使用非石油基液压制动液的液压制动主液压缸储油器的膜片密封垫

이 규격은 도로 차량에 사용하는 유압 브레이크 마스터 실린더 저장용기의 다이어프램 개스킷에

Road vehicles－Diaphragm gaskets for hydraulic brake master cylinder reservoirs using a non-petroleum base hydraulic brake fluid

BS ISO 1103:2007 道路车辆.居住挂车和轻型挂车的联接球.尺寸

This International Standard lays down the dimensions necessary for the compatibility of mechanical coupling devices between light trailers or caravans and towing vehicles, when the latter are fitted with a coupling ball. The clearance space around the coupling ball is intended to allow coupling and decoupling of towed vehicles, as well as safe operation during coupling and uncoupling of mechanical devices. This International Standard applies to coupling balls designed to couple caravans and light trailers of categories O1 and O2 1) to vehicles of categories M or N. It does not necessarily apply to special trailers drawn by special vehicles.

Road vehicles - Coupling balls for caravans and light trailers - Dimensions

JT/T 650-2006 冷藏保温厢式挂车通用技术条件

本标准规定了冷藏保温厢式挂车的术语和定义、技术要求及试验方法。 本标准适用于在道路上使用的冷藏保温厢式挂车。

Technical specification for refrigerated and insulated van trailer

ASTM E2517-06 III型(M35A2型2.5吨货运卡车/M1078型2.5吨中轻型装甲车/M1082型2.5吨拖车)货运车斗盖的标准规范

1.1 This specification covers the general requirements for the Type III Cargo Bed Cover (CBC). The Type III Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M35A2, 21/2 Ton Cargo Truck/M1078, 2 1/2 Ton Lightweight Medium Tactical Vehicle (LMTV)/M1082, 2 1/2 Ton LMTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parenthesis are for information only.The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Cargo Bed Cover, Type III (M35A2, 2 1/2 Ton Cargo Truck/M1078, 2 1/ 2 Ton Lightweight Medium Tactical Vehicle (LMTV)/M1082, 2 1/ 2 Ton LMTV Trailer)

DIN 74255:2005 拖挂车.操纵杆图形符号

Towed Vehicles - Graphical symbols for levers

DIN 74086:1996 道路车辆.挂车运行静负荷

Limiting values for the actual and allowable static load are given.

Road vehicles - Static load for trailers in operation

JIS D 6603:1995 牵引车和半挂车互连尺寸

Interchange coupling dimensions of truck tractors and semitrailers

ISO 4091:1992 道路车辆 牵引车和挂车之间电气连接用连接器 试验方法和性能要求

Road vehicles; connectors for electrical connections between towing vehicles and trailers; test methods and performance requirements