共找到 336 条与 摩托车综合 相关的标准,共 23 页
Motorcycles-Steady state circular test procedure
本标准规定了以蓄电池或磁电机为电源的摩托车和轻便摩托车用电器零部件的试验电压。 本标准适用于以蓄电池或磁电机为电源的摩托车和轻便摩托车用电气零部件(启动电机及磁电机除外)。
Testing voltage for motorcycles and mopeds electric equipment
本标准规定了摩托车和轻便摩托车铝合金车轮的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于摩托车和轻便摩托车用铝合金整体车轮。
General Techniques and Testing Method for Aluminium-Alloy Wheels of Motorcycles and Mopeda
この規格は,二輪自動車(以下,自動車という。)に関する用語について規定する。注記 二輪自動車とは,2個の車輸をもっている2軸自動車をいう。ただし,側車付二輪自動車を含む。
Motorcycles and mopeds -- Vocabulary
The purpose of this SAE Recommended Practice is to specify the procedure for measuring the bank angle of motorcycles. This document applies to all two-wheeled motorcycles as defined in SAE J213.
Motorcycle Bank Angle Measurement Procedure
이 규격은 새로운 가솔린 기관 차량 설계와 (능동 및 수동 장치 모두의) 주유 증기 회수
Road vehicles-Filler pipes and openings of motor vehicle fuel tanks-Vapour recovery system
이 규격은 주행 시험을 하는 이륜 자동차(이하 자동차라 한다.)에 부착된 속도계 및 적산계
Mopeds and motorcycles-Speedometers-Methods of calibration
本标准规定了进出口两轮全场地车的要求、检验及判定。 本标准适用于进出口两轮全场地车的检验、也适用于进出口非公路用两轮摩托车的检验。
Rules for the inspection of two-wheeled all terrain vehicle for import and export
This International Standard specifies methods for determining the performance of light-alloy road wheels for motorcycles under normal road use. This International Standard is applicable to wheels for motorcycles with two or three wheels (including motorcycles equipped with side-cars) as defined in ISO 3833, of the following types: - unit construction light-alloy wheels; and - composite construction light-alloy wheels.
Motorcycles - Light-alloy wheels - Test method
Motorcycles - Methods for setting the running resistance on a chassis dynamometer
This International Standard specifies the measurement method for determining the motorcycle running resistance on the road, and two methods of setting the chassis dynamometer with the motorcycle running resistance. It is applicable to motorcycles as defined in ISO 3833.
Motorcycles - Methods for setting running resistance on a chassis dynamometer
本标准规定了摩托车和轻便摩托车技术参数表(以下简称技术参数表)格式及项目填写要求。 本标准适用于摩托车和轻便摩托车(以下简称摩托车)。
Motorcycles and mopeds--The form format of technical parameters
この規格は,ガソリン又は含酸素成分混合ガソリン(以下,ガソリンという。)を燃料とする火花点火機関を搭裁したニ輪自動車(原動機付自転車,二輪自動車及び側車付二輸自動車を指す。以下,二輪車という。)が,シャシダイナモメータ上で一定速度走行運転及びモード(以下,テストサイクルという。)運転を行ったときの燃料消費率の測定方法につて規定する。
Gasoline-fueled two-wheeled vehicles -- Measurement of fuel consumption on a given driving cycle on a chassis dynamometer
Motorcycles. Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles. Standardized procedures for performing computer simulations of motorcycle impact tests
Motorcycles. Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles. Full-scale impact-test procedures
Motorcycles. Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles. Motorcyclist anthropometric impact dummy
Motorcycles. Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles. Injury indices and risk/benefit analysis
Motorcycles. Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles. Definitions, symbols and general considerations
This part of ISO 13232 specifies minimum requirements for the collection and analysis of all motorcycle accident data, in order to provide: -- a standardized and representative sub-set of car/motorcycle accident data; and -- a sub-set of car/motorcycle impact conditions based on the analysis of this standardized accident data. ISO 13232 specifies the minimum requirements for research into the feasibility of protective devices fitted to motorcycles, which are intended to protect the rider in the event of a collision. ISO 13232 is applicable to impact tests involving: -- two-wheeled motorcycles; -- the specified type of opposing vehicle; -- either a stationary and a moving vehicle or two moving vehicles; -- for any moving vehicle, a steady speed and straight-line motion immediately prior to impact; -- one helmeted dummy in a normal seating position on an upright motorcycle; -- the measurement of the potential for specified types of injury by body region; and -- evaluation of the results of paired impact tests (i.e. comparisons between motorcycles fitted and not fitted with the proposed devices). ISO 13232 does not apply to testing for regulatory or legislative purposes.
Motorcycles - Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles - Definition of impact conditions in relation to accident data
Motorcycles. Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles. Documentation and reports
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号