T80 摩托车综合 标准查询与下载

QC/T 235-2008 摩托车和轻便摩托车排气消声器技术要求和试验方法

本标准规定了摩托车和轻便摩托车（以下简称摩托车）排气消声器的技术要求与试验方法、检验规则和标志、包装、运输、储存等要求。 本标准适用于摩托车用的排气消声器。

Specification and test methods for exhaust mumer of motorcycles and mopeds

QC/T 801-2008 摩托车和轻便摩托车簧片阀式二次空气补给机构技术要求和试验方法

本标准规定了摩托车和轻便摩托车用簧片阀式二次空气补给机构的技术要求和试验方法。 本标准适用于由单向簧片阀（以下简称簧片阀）和二次空气截止阀（以下简称截止阀）组合而成的摩托车和轻便摩托车用簧片阀式二次空气补给机构（以下简称二次空气补给机构）。其他结构的二次空气补给机构可以参照使用。

Technical requirements and testing methods of reed valve type second air injectors for motorcycles and mopeds

ISO 9129:2008 摩托车.惯性矩的测量方法

Motorcycles - Measurement methods for moments of inertia

BS ISO 9043:2008 轻便摩托车.惯性矩测量方法

Mopeds - Measurement method for moments of inertia

ISO 9043:2008 机动脚踏两用车.惯性矩的测量方法

This International Standard specifies a measuring method for determining the moments of inertia of the moped and of the moped/rider combination. It applies to two-wheeled mopeds. Other measuring methods can be used if it is demonstrated that the results are equivalent. Measurement results obtained exclusively by the method described in this International Standard (see Annex A) cannot be used for an evaluation of vehicle stability because they deal with only one aspect of this very complex phenomenon.

Mopeds - Measurement method for moments of inertia

KS R ISO 2697:2007 柴油机.燃料喷嘴."S"规格

이 규격은 디젤 기관용 S 사이즈 연료 노즐의 주요 치수 요구사항에 대하여 규정한다.

Diesel engines－Fuel nozzles－Size “S”

KS R ISO 2699:2007 柴油机.法兰盘上安装的"S"规格燃料喷射器.2、3、4、5和6型

이 규격은 디젤 기관(압축 착화 기관)에 사용되는 KS R ISO 2697에 규정된 노즐을

Diesel engines－Flange-mounted fuel injectors, size “S”－Types 2, 3, 4, 5 and 6

SANS 311:2007 L类机动车辆

Specifies the requirements for category L motor vehicles. Applies in respect of incomplete vehicles supplied by one manufacturer to another for further manufacture. Applies to vehicles after completion of further manufacture by the latter manufacturer. D

Category L motor vehicles

SAE J392-2007 设计电压的摩托车和电动摩托车电气系统维护

This SAE Recommended Practice pertains to electrical systems of motorcycles both with and without batteries. This document provides minimum illumination voltage values for motorcycle classifications as specified in SAE J 213 describes test procedures to determine that these voltages are maintained.

Motorcycle and Motor Driven Cycle Electrical System Maintenance of Design Voltage

QC/T 791-2007 电动摩托车和电动轻便摩托车定型试验规程

本标准规定了电动摩托车和电动轻便摩托车新产品设计定型试验的实施条件及试验项目、试验方法和评定依据以及试验程序、试验报告所需的内容。 本标准适用于电动摩托车和电动轻便摩托车(定义见GB/T 24158-2009)(除特殊说明外,以下简称为电动摩托车)。

Electric motorcycles and electric mopeds-Engineering approval evaluation program

QC/T 688-2007 摩托车和轻便摩托车通用技术条件

本标准规定了摩托车和轻便摩托车的要求、试验方法、检验规则及标志、使用说明书、包装、运输和储存。 本标准适用于在我国道路上行驶的各类型摩托车和轻便摩托车（以下简称摩托车）。

General specifications of motorcycles and mopeds

BS ISO 6460-1:2007 摩托车.废气排放和燃料消耗的测量方法.一般试验要求

This part of ISO 6460 specifies the general test requirements for measurement for the gaseous exhaust emissions from motorcycles, and for determining the fuel consumption of motorcycles as defined in ISO 3833. It is applicable to motorcycles equipped with a spark ignition engine (four-stroke engine, two-stroke engine or rotary piston engine) or a compression ignition engine.

Motorcycles - Measurement method for gaseous exhaust emissions and fuel consumption - General test requirements

BS ISO 6460-3:2007 摩托车.废气排放和燃料消耗测量方法.恒速下的燃料消耗测量

This part of ISO 6460 specifies the methods measurement for fuel consumption at a constant speed on the road and on the chassis dynamometer.It is applicable to motorcycles as defined in ISO 3833,equipped with a spark ignition engine (four-stroke engine,two-stroke engine or rotary piston engine)or a compression ignltion engine.

Motorcycles - Measurement method for gaseous exhaust emissions and fuel consumption - Fuel consumption measurement at a constant speed

BS ISO 6460-2:2007 摩托车.废气排放和燃料消耗测量方法.试验车和特殊试验条件

This part of ISO 6460 defines test cycles for measurement for the gaseous emissions from motorcycles,as well as for determining the fuel consumption of motorcycles as defined in ISO 3833,equipped with a spark ignition engine (four-stroke engine,two-stroke engine or rotary piston engine)or a compression ignltion engine.

Motorcycles - Measurement method for gaseous exhaust emissions and fuel consumption - Test cycles and specific test conditions

ISO 6460-1:2007 摩托车.废气排放和燃料消耗测量方法.第1部分:一般试验要求

This part of ISO 6460 specifies the general test requirements for measurement for the gaseous exhaust emissions from motorcycles, and for determining the fuel consumption of motorcycles as defined in ISO 3833. It is applicable to motorcycles equipped with a spark ignition engine (four-stroke engine, two-stroke engine or rotary piston engine) or a compression ignition engine.

Motorcycles - Measurement method for gaseous exhaust emissions and fuel consumption - Part 1: General test requirements

ISO 6460-3:2007 摩托车.废气排放和燃料消耗的测量方法.第3部分:恒速下的燃料消耗测量

This part of ISO 6460 specifies the methods measurement for fuel consumption at a constant speed on the road and on the chassis dynamometer.It is applicable to motorcycles as defined in ISO 3833,equipped with a spark ignition engine (four-stroke engine,two-stroke engine or rotary piston engine)or a compression ignltion engine.

Motorcycles - Measurement method for gaseous exhaust emissions and fuel consumption - Part 3: Fuel consumption measurement at a constant speed

ISO 6460-2:2007 摩托车.废气排放和燃料消耗的测量方法.第2部分:试验循环和特殊试验条件

This part of ISO 6460 defines test cycles for measurement for the gaseous emissions from motorcycles,as well as for determining the fuel consumption of motorcycles as defined in ISO 3833,equipped with a spark ignition engine (four-stroke engine,two-stroke engine or rotary piston engine)or a compression ignltion engine.

Motorcycles - Measurement method for gaseous exhaust emissions and fuel consumption - Part 2: Test cycles and specific test conditions

SAE J1451-2007 单轮距车辆动力和操作的术语字典(摩托车、机动脚踏两用车和自行车)

This dictionary of terms was prepared for use by those with a need to describe and understand the dynamics and handling of two-wheeled, single track vehicles. It is intended to span the gap between vehicle dynamics specialists and those with a more general interest. This report is pertinent to such areas as vehicle design and development, the description of two-wheeler properties, rider training and education, and the preparation of standards and regulations. This report was prepared by the SAE Motorcycle Committee, which solicits suggestions for improvements and additions to be considered in future revisions. comments should be directed to SAE Headquarters.

A Dictionary of Terms for the Dynamics and Handling of Single Track Vehicles (Motorcycles, Mopeds, and Bicycles)

JASO T006-2007 摩托车.H点测定用程序

Motorcycles-Procedure for H-point Determination

JASO T013-2007 摩托车.行车道改变试验程序

Motorcycles-lane change test procedure