U18 小型船总体 标准查询与下载

ISO 16147:2020 小型船舶. 船内柴油发动机. 安装在发动机上的燃料、油和电气组件

This document establishes requirements for the design and installation of engine-mounted fuel, oil and electrical components on diesel inboard-mounted engines for minimizing fuel leakage, risk of electric shock and the risk of and/or the spread of fire on small craft of hull length up to 24 m in accordance with ISO 8666.

Small craft - Inboard diesel engines - Engine-mounted fuel, oil and electrical components

ISO 9093:2020 小艇. 通海旋塞及贯穿艇体配件

Small craft - Seacocks and through-hull fittings

ISO 13297:2020 小型船舶. 电气系统. 交流和直流电气设备

This document specifies the requirements for the design, construction and installation of the following types of DC and AC electrical systems, installed on small craft either individually or in combination: a) extra-low-voltage direct current (DC) electrical systems that operate at nominal potentials of 50 V DC or less; b) single-phase alternating current (AC) systems that operate at a nominal voltage not exceeding AC 250 V. This document does not cover the following: — electrical propulsion systems of direct current less than 1500 V DC, single-phase alternating current up to 1000 V AC, and three-phase alternating current up to 1000 V AC, which are addressed — any conductor that is part of an outboard engine assembly and that does not extend beyond the outboard engine manufacturers supplied cowling; — three-phase AC installations that operate at a nominal voltage not exceeding 500 V AC, which are addressed by IEC 60092-507.

Small craft - Electrical systems - Alternating and direct current installations

BS EN ISO 8666:2020 小艇. 主要数据

Small craft. Principal data

NF J95-059:2020 小艇. 操舵部位的视野

Le présent document spécifie les exigences relatives au champ de vision depuis le poste de pilotage, vers l'avant (horizontalement et verticalement) et vers l'arrière, pour les petits navires d'une longueur de coque (LH) inférieure ou égale à 24 m conformément à l'ISO 8666:2016.

Small craft - Field of vision from the steering position

JT/T 1283.3-2019 全垫升气囊浮体气垫船 第3部分：气垫船气囊

Fully Cushioned Airbag Floating Hovercraft Part 3: Hovercraft Airbag

JT/T 1283.2-2019 全垫升气囊浮体气垫船 第2部分：围壁气囊气垫船

Fully Cushioned Airbag Floating Hovercraft Part 2: Walled Airbag Hovercraft

JT/T 1283.1-2019 全垫升气囊浮体气垫船 第1部分：侧壁气囊气垫船

Fully Cushioned Airbag Floating Hovercraft Part 1: Sidewall Airbag Hovercraft

BS EN ISO 12215-1:2018 小工艺品 船体结构和尺寸 材料：热固性树脂、玻璃纤维增强材料、参考层压板

Small craft. Hull construction and scantlings. Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate

BS EN ISO 11547:2018 小工艺品 齿轮启动保护

Small craft. Start-in-gear protection

BS EN ISO 8666:2018 小艇. 主要数据

Small craft. Principal data

BS EN ISO 15083:2018 小艇. 舱底污水抽吸系统

Small craft. Bilge-pumping systems

BS EN ISO 13297:2018 小艇. 电气系统. 交流电装置

Small craft. Electrical systems. Alternating current installations

BS EN ISO 15084:2018 小工艺品 抛锚、系泊和拖曳 优点

Small craft. Anchoring, mooring and towing. Strong points

BS EN ISO 12215-4:2018 小工艺品 船体结构和尺寸 车间及制造

Small craft. Hull construction and scantlings. Workshop and manufacturing

BS EN ISO 6185-1:2018 充气艇. 电动机最大额定功率为4.5 kW的小型船舶

Inflatable boats. Boats with a maximum motor power rating of 4,5 kW

BS EN ISO 12216:2018 小船. 窗口,舷窗,舱口,舷窗盖和门的强度和不透水性要求

Small craft. Windows, portlights, hatches, deadlights and doors. Strength and watertightness requirements

BS EN ISO 6185-3:2018 充气船 船体长度小于 8m、电机额定功率为 15kW 及以上的船舶

Inflatable boats. Boats with a hull length less than 8 m with a motor rating of 15 kW and greater

BS EN ISO 12215-2:2018 小工艺品 船体结构和尺寸 材料：夹层结构的核心材料、嵌入材料

Small craft. Hull construction and scantlings. Materials: Core materials for sandwich construction, embedded materials

BS EN ISO 6185-2:2018 充气船 最大电机额定功率为 4.5kW 至 15kW（含）的船只

Inflatable boats. Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive