U55 船用管件 标准查询与下载

JIS F 7152 AMD 1:2013 船用发动机湿排气系统用橡胶和塑料软管.规格(修改件1)

Rubber and plastics hoses for marine-engine wet-exhaust systems -- Specification (Amendment 1)

JIS F 7805:2013 船舶和海洋技术.船用钢制废气管法兰

Ships and marine technology.Marine steel pipe flanges for exhaust gas pipe

SAE J2006-2013 船用排气软管

This SAE Standard covers the flexible components of marine engine wet exhaust systems from the connection at the engine exhaust manifold to the hull or overboard discharge fittings.

Marine Exhaust Hose

DIN 86210-2:2013 海船运营物资的补给和液体废料的处置.第2部分:小于PN 10紧急释放联轴器

Replenishment with operating materials and disposal of fluid waste from seagoing vessels.Part 2: Emergency release couplings up to PN 10

KS V 7512-2013 发动机舱钢梯和栏杆

이 표준은 기관실 통로에 사용하는 강제 사다리(이하, “사다리”라 한다.) 및 강제 핸드레

Steel ladders and handrails for engine room

CB 20039-2012 铁白铜管焊接技术要求

本标准规定了铁白铜管钨极氩弧焊(TIG焊)焊接的一般要求、焊接工艺和焊接安全防护等。本标准适用于壁厚范围在1mm~6mm、公称通径范围在10mm~700mm铁白铜管的对接焊。

Technical requirements for Cu-Ni-Fe alloy pipes welding

CB 20062-2012 舰船用热交换器管的涡流检验方法

本标准规定了舰船用热交换器管(以下简称热交换器管)涡流检验的一般要求、对比试样要求、检验程序和方法、检验结果评定等。本标准适用于非铁磁性材料(例如铜及铜合金、铝及铝合金、钛及钛合金等)制成的在役热交换器直管的涡流检验,不适用于翅片管(含肋片管)、波纹管、螺旋管的涡流检验。

Eddy current inspection method for heat exchanger tubes of ships

CB 20091-2012 铝合金-铝-钢（不锈钢）复合过渡接头规范

本规范规定了规定了铝合金-铝-钢(不锈钢)复合过渡接头(以下简称过渡接头)的要求、质量保证规定以及交货准备等。本规范适用于舰船的钢结构与铝结构连接用铝合金-铝-钢(不锈钢)复合过渡接头的制造、检验和验收,其他船舶及海洋工程可参照使用。

Specification for aluminium alloys - aluminium - steel(stainless steel) clading transition jiont

CB 20067-2012 铁白铜管松套钢法兰

本标准规定了舰船用铁白铜管松套钢法兰(以下简称松套钢法兰)的型式和尺寸、要求、试验方法、检验规则、标志和包装。本标准适用于淡水、海水、生活污水、污油水等舰船管路中系统工作压力不大于1.6 MPa的铁白铜管松套钢法兰的设计、制造和验收。

Combination flanges for Cu-Ni-Fe alloy pipes

CB 20037-2012 船用空气管头

本标准规定了法兰连接尺寸按CB/T 4196—2011,GB/T 2501—2010中公称压力为0.6 MPa的的船用油、水舱空气管头(以下简称空气管头)的分类和标记、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于各类船舶和海上钻井平台用的油、水舱空气管头的设计、制造和检验。

Marine air vent head

CB 202-2012 螺纹接头通舱管件

本标准规定了螺纹接头通舱管件(以下简称通舱管件)的分类、要求、试验方法、检验规则、标志和包装。本标准适用于油类、淡水、海水、蒸溜水等介质的船舶管路系统用通舱管件的设计、制造和验收。

Through bulkhead pieces with thread joint

CB 497-2012 吸入粗水滤器

本标准规定了法兰连接尺寸和密封面按GB/T 569、GB/T 2501的吸入粗水滤器(以下简称滤器)的分类、要求、试验方法、检验规则、标志和包装。本标准适用于船舶海水、淡水管路系统滤器的设计、制造和验收。

Water filters

CB 177-2012 船用夹布胶管接头通用技术条件

本标准规定了船用夹布胶管接头(以下简称接头)的分类和要求。本标准适用于船舶管路系统用各类夹布胶管的阀件和管件的设计。

General specifications of marine bakelite pipe fittings

ANSI/ASTM F894:2013 聚乙烯(PE)大口径异形内壁污水管和排水管标准规格

Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe

DIN 86061:2013 公称压力为10的钢管用带管法兰的连接套管

Connecting sockets with pipe flange, for steel tubes, nominal pressure 10

DIN 86064:2013 公称压力为10的钢管用带管法兰和固定环的连接套管

Connecting sockets with pipe flange and fixing collar, for steel tubes, nominal pressure 10

DIN 86072-2:2013 船舶排气管道. 垫圈. 第2部分: 法兰连接灯光设计垫圈

Exhaust gas lines on ships.Gaskets.Part 2: For flanged connections light design

DIN 86044-2:2013 船舶排气管道. 法兰. 第2部分: 灯光设计

Exhaust gas lines on ships.Flanges.Part 2: Light design

DIN 86059:2013 公称压力为10的钢管用带固定套环的法兰管闷头

Flanged bulkhead pieces with fixing collar, for steel tubes, nominal pressure 10

EN 1124-4:2013 污水系统用带插口和插座的纵向焊接不锈钢管和配件.第4部分:真空排水系统和船用排水系统的部件

This European Standard specifies requirements, dimensions and tolerances for pipes and fittings of longitudinally welded, stainless steel pipe with spigot and socket used for vacuum drainage systems inside and outside buildings and for gravity and vacuum drainage systems on ships and floating maritime structures1): above freeboard deck as long as the heeling is taken into account in the event of damage when installed above freeboard deck on passenger ships; inside a watertight compartment below freeboard deck; with direct connection to the outboard (not permitted below freeboard deck); inside tanks as long as these are not filled with foreign media and are not cargo tanks. On well-anchored maritime structures, this European Standard applies to pipes and fittings of longitudinally welded stainless steel pipe with spigot and socket used in drainage systems in the accommodation area. Pipes and fittings according to this European Standard may also be used in central vacuum cleaning installations, in vacuum suction lifting installations, in chip transporting installations and in other waste water and process pipes as long as the media to be discharged do not damage the components or the health and safety of the personnel. For other pipes, this European Standard only applies if agreed with the relevant operators and following prior consultation with the manufacturer. This European Standard contains a designation system for the different types of pipes and fittings for easy identification of each component. This European Standard is only applicable in conjunction with EN 1124-1.

Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for wastewater systems - Part 4: Components for vacuum drainage systems and for drainage systems on ships