共找到 2056 条与 航空与航天用非金属材料 相关的标准,共 138 页
Aerospace series. Non-metallic materials. Textiles. Test method. Determination of water extractable matter
Aerospace series - Non-metallic materials - Glass transparencies - Material standard - Thermally tempered soda lime float glass
This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a corrosion and heat resistant aluminum coating material supplied as a liquid of suitable consistency for coating parts after being thoroughly mixed. Primarily for coating ferrous parts to be exposed to temperatures below 650°C (1200°F).
Aluminum Coating Material, Corrosion and Heat Resistant, Thermosetting, Inorganic Binder
This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers two-component colored systems composed of a resin and a miscible hardener supplied in kit form. Primarily for identification marking of parts and equipment exposed to temperatures from -55 to +150 degrees C (-65 to +300 degrees F) where various colors are needed. Systems produce tile-like compounds with good hardness, moisture and solvent resistance, and adhesion to metallic surfaces when properly
Paint, Marking Epoxy
This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification has been declared ""NONCURRENT"" by the Aerospace Materials Division, SAE, as of October, 2007. It is recommended, therefore, that this specification not be specified fro new designs. ""NONCURRENT"" refers to those specifications which have previously been widely used and which may be required for production or processing of existing designs in the future. The Aerospace Materials Division, however, does
Coating, Urethane, Aliphatic Isocyanate, Polytetrafluoroethylene Filled
This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification has been declared ""CANCELLED"" by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been ""CANCELLED"". This specification covers a semigloss black baking enamel based on a phenolic resin. Primarily as a coating for metal surfaces exposed to corrosive c
Enamel, Phenolic, Black Baking
This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification has been declared ""CANCELLED"" by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been ""CANCELLED"". This specification covers face-up type of water applied, solvent-applied, or adhesive-applied decalcomanias. These decalcomanias have been used prima
Decalcomanias
Wire, Electrical, Fluoropolymer-Insulated, Crosslinked Modified ETFE, Low Fluoride, Normal Weight, Silver-Coated Copper, 200 degree C, 600 Volt
This specification covers a standard fluorosilicone (FVMQ) rubber stock in the form of molded test slabs.
Test Slabs, Fluorosilicone (FVMQ), 55-65
This specification covers one width and one breaking strength of low modulus aramid tubular webbing.
Webbing, Tubular, Low Modulus Aramid 3/4 (19) Wide, 2300 (10 231) Breaking Strength
This specification covers a silicone rubber material that can be used to manufacture product in the form of sheet, strip, tubing, molded shapes, and extrusions. This specification should not be used to address products such as O-rings, compression seals, O-ring cord, and molded-in-place gaskets.
Silicone Rubber, 1000 psi (6.89 MPa) Minimum Tensile Strength, 55-65 Durometer
This specification covers one width and one strength of low modulus aramid tubular webbing.
Webbing, Tubular, Low Modulus Aramid 1 (25) Wide, 4000 (17 793 ) Breaking Strength
This specification covers one width and one breaking strength of low modulus aramid tubular webbing.
Webbing, Tubular, Low Modulus Aramid 3-3/16 (81) Wide, 2250 (10 008) Breaking Strength
Aerospace series - Non-metallic materials - Glass transparencies - Material standard - Chemically tempered soda lime float glass
Aerospace series - Non-metallic materials - Glass transparencies - Test methods - Determination of ream and surface ripple
Aerospace series - Non-metallic materials - Glass transparencies - Test methods - Determination of flatness
This specification covers a coating consisting of finely-powdered graphite in a heat-resistant inorganic binder. This coating has been used typically on metal parts and selected nonmetallic materials requiring a coating less than 0.0001 inch (2.5 um) thick for reducing wear or minimizing galling, but usage is not limited to such applications.
Graphite Coating, Thin Lubricating Film Impingement Applied
This European Standard specifies the procedure for the determination of water extractable matter of textile material. This method has been written in response to an aerospace requirement for a method of extraction using hot water.
Aerospace series - Non-metallic materials - Textiles - Test method - Determination of water extractable matter
This European Standard specifies the determination of water soluble chloride and sulphate of aqueous extracts of textile materials. This method has been written in response to an aerospace requirement for a method of extraction using hot water, this method should be used in conjunction with EN 4426.
Aerospace series - Non-metallic materials - Textiles - Test method - Determination of water soluble chloride and sulfate of aqueous extracts
This European Standard specifies the procedure for the determination of dimensional stability of narrow fabrics.
Aerospace series - Non-metallic materials - Textiles - Test method - Determination of dimensional stability
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号