V13 航空与航天用非金属材料 标准查询与下载

GOST R 56499-2015 适用于航空玻璃的定向丙烯酸片材. 试验方法

Oriented acrylic sheets focused for aviation glazing. Test methods

BS EN 3825:2014 航空航天系列. 硅氟橡胶 (FVMQ). 硬度60 IRHD

Aerospace series. Fluorosilicone rubber (FVMQ). Hardness 60 IRHD

EN 3827:2014 航空航天系列.氟硅橡胶（氟硅橡胶）.80 IRHD硬度

This standard specifies the properties of fluorosilicone rubber (FVMQ)1), hardness 80 IRHD, for aerospace applications.

Aerospace series - Fluorosilicone rubber (FVMQ) - Hardness 80 IRHD

EN 3825:2014 航空航天系列.氟硅橡胶（氟硅橡胶）.60 IRHD硬度

This European Standard specifies the properties of fluorosilicone rubber (FVMQ)1), hardness 60 IRHD, for aerospace applications.

Aerospace series - Fluorosilicone rubber (FVMQ) - Hardness 60 IRHD

EN 3826:2014 航空航天系列.氟硅橡胶（氟硅橡胶）.70 IRHD硬度

This European Standard specifies the properties of fluorosilicone rubber (FVMQ)1), hardness 70 IRHD, for aerospace applications.

Aerospace series - Fluorosilicone rubber (FVMQ) - Hardness 70 IRHD

QJ 2676A-2014 吸附剂低温低压吸附性能试验方法　

本标准规定了吸附剂低温低压吸附性能试验的试验原理、一般要求、试验装置、试样制备、试验程序、数据处理和试验报告。 本标准适用于采用真空绝热型的低温容器、低温装置、低温输送管路和低温阀门中使用的活性炭和分子筛吸附剂在低温（小于120K)、低压（10Pa~10Pa)下的吸附性能试验。其他吸附剂的吸附性能测试可参照执行。

Test method for adsorption properties of adsorbents at low temperature and pressure

QJ 1322A-2014 真空中材料质量损失测试方法　

本标准规定了非金属材料在真空中质量损失测试的测试设备、测试条件、测量仪器检定要求、试样制备、测试程序、数据记录及处理和测试报告。 本标准适用于测试非金属材料在真空环境中的质量损失。

Test method for mass loss of materials in vacuum

QJ 2727A-2014 碳纤维／酚醛－高硅氧纤维／酚醛复合摸压制品规范

本规范规定了碳纤维/酚醛-高硅氧纤维/酚醛复合模压制品（以下简称制品）的要求、质量保证规定和交货准备等。 本规范适用于由粘胶基碳纤维/酚醛-高硅氧纤维/酚醛复合模压成型的固体火箭发动机喷管烧蚀防热制品的检验与验收。其他用途的模压制品可参照执行。

Specification for carbon fiber/phenolic-silica fiber/phenolic compression mold products

QJ 2331A-2014 蜂窝夹层结构碳纤维／环氧复合材料面板制造技术要求

本标准规定了蜂窝夹层结构碳纤维/环氧复合材料面板制造技术的一般要求、检验要求、质量控制、运输和贮存等内容。 本标准适用于蜂窝夹层结构碳纤维/环氧F46 (环氧AG80)复合材料面板（以下简称面板）制造，适用的碳纤维的牌号包括T300、T700、T800、M40、M40JB、M46JB、M55JB、M60JB、MT300。其他牌号的碳纤维、树脂基体制造的面板可参照使用。

Process technical requirements for honeycomb sandwich construction carbon/epoxy composite facing

SAE AMS3217/7A-2014 55-65 氟硅氧烷 (FVMQ) 高强度试验板

This specification covers a high strength fluorosilicone (FVMQ) rubber stock in the form of molded test slabs.

Test Slabs, High Strength, Fluorosilicone (FVMQ) 55 - 65

SAE ARP5088B-2014 用自动电位滴定测定聚酯和二酯燃气涡轮润滑剂中总酸值的试验方法

The test method describes the procedure for determination of the total acid number of new and degraded polyol ester and diester based gas turbine lubricants by potentiometric titration technique. The method was validated to cover an acidity range 0.05 to 6.0 mg KOH g-1. The method may also be suitable for the determination of acidities outside of this range and for other classes of lubricant.

Test Method for the Determination of Total Acidity in Polyol Ester and Diester Gas Turbine Lubricants by Automatic Potentiometric Titration

SAE AMS3194E-2014 坚定的极端低温闭孔硅橡胶海绵

This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.

Silicone Rubber Sponge Closed Cell, Firm, Extreme Low Temperature

SAE AMS3325F-2014 耐燃料及耐油氟硅(FVMQ)橡胶,55-65

This specification covers a fluorosilicone (FVMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts requiring resistance to jet fuel and lubricating oils, but usage is not limited to such applications. Generally, products are usable over a temperature range of -76 to +302 degrees F (-60 to +150 degrees C); each application, however, has to be considered individually.

Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant 55 - 65

SAE AMS3193E-2014 中等温度和极低温度的闭孔硅橡胶海绵

This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.

Silicone Rubber Sponge Closed Cell, Medium, Extreme Low Temperature

SAE AMS-R-83485A-2014 在低温条件下具备改良性能的氟烃弹性体橡胶

This specification covers high temperature, compression set, and fluid resistant fluorocarbon elastomer sheets, strips, molded parts, and extruded shapes for aeronautical and aerospace applications. This material differs from other fluorocarbon elastomers because of its improved low temperature performance of approximately 25 °F.

Rubber, Fluorocarbon Elastomer, Improved Perfrormance At Low Temperatures

SAE AMS3195G-2014 中等硅泡沫橡胶闭孔泡沫

This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.

Silicone Rubber Sponge Closed Cell, Medium

SAE AMS3306C-2014 硅树脂橡胶,1200 psi(8.27 MPa),高模55-65

This specification covers a silicone elastomer in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically as seals from -65 degrees to +225 degrees C (-85 degrees to +437 degrees F), compounded especially for high strength. Silicone rubber is resistant to deterioration by weathering and by high-aniline-point petroleum-base lubricating oil and phosphate ester hydraulic fluid, and remains flexible over the temperature range noted. This material is not normally suitable for use in contact with hydrocarbon-based fuels and low-aniline-point petroleum-base fluids due to excessive swelling of the elastomer, but usag

Rubber, Silicone 1200 psi (8.27 MPa), High Modulus 55 - 65

HB 5470-2014 民用飞机机舱内部非金属材料燃烧性能要求

本标准规定了民用飞机机舱内部非金属材料燃烧试验类型、试验类型所对应的机舱内部非金属材料应用部位及燃烧性能要求等。 本标准适用于民用飞机机舱内部非金属材料性能检验。

Requirements of burning performance for cabin interior nonmetallic material of civil aircraft

HB 5469-2014 民用飞机机舱内部非金属材料燃烧试验方法

本标准规定了民用飞机机舱内部非金属材料燃烧试验的试验类型、试验设备和器材、试样、试验要求、试验程序及试验报告。 本标准适用于民用飞机机舱内部非金属材料燃烧性能试验。

Burning test method for cabin interior nonmetallic material of civil aircraft

SAE AMS3198L-2014 中硬度氯丁海绵橡胶

This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered. These products have been used typically for general applications requiring the use of open-cell, medium sponge rubber pads and seals operating from -40 to +80 degrees C (-40 to +176 degrees F), but usage is not limited to such applications.

Sponge, Chloroprene (CR) Rubber, Medium Stiffness