共找到 84 条与 弹性元件 相关的标准,共 6 页
This standard establishes the dimensional and visual quality requirements and packaging and labeling requirements for O-Rings molded from AMS 7268 rubber. It shall be used for procurement purposes.
Packing, Preformed, O-Ring Molded from AMS 7268 Material
This draft is now available for public comment and your views and technical comments on it would be appreciated. If you have no specific comments to make hut find it generally acceptable it would be helpful if you would notify US accordingly. Suggestions entailing revision of the text should indicate the preferred wording. Please quote the relevant clause number against any comment.
Aerospace series Washer, spring, countersunk Edition P 2
This standard specifies the required characteristics for lamp, code 1619, used on-board aircraft. It shall be used together with EN 2756.
Aerospace series Welded and brazed assemblies for aerospace constructions Weldability and brazeability of materials Part 001: General requirements Edition P1
This standard specifies the dimensions, tolerances, required characteristics and masses of a circlip for use in fuselage interior equipment and structural applications. This standard shall be used in conjunction with stud per EN 6088 and retaining washer per EN 6089.
Aerospace series Circlip Edition P 1
The purpose of this standard is to provide general requirements for the marking of raw materials, products and components.
IDENTIFICATION MARKING REQUIREMENTS FOR SPECIAL PURPOSE COMPONENTS
The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil
FASTENERS, SNAP, STYLE 6 (FUNNEL NECK BUTTON HEAD TYPE)
The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil
FASTENER, SNAP, STYLE 1 (LARGE CURTAIN TYPE)
The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil
FASTENER, SNAP, STYLE IB (MUD-PROOF CURTAIN TYPE)
This standard specifies the characteristics of spring tension clips for the support of electrical harnesses, in FE-PA3903 for aerospace applications. Maximum operating temperature: 250 ?,,#
Aerospace series - Clips, spring tension, in alloy steel FE-PA3903; German and English version EN 4420:2003
SPRING, HELICAL, COMPRESSION: FOR LOADS BELOW 20 POUNDSTABLE 1 - CORRECTION FACTOR FOR STRESS RANGE LIFE CYCLES AND SPRING MATERIALTABLE 2 - DIMENSIONS AND CHARACTERISTICS TABLE 2 - CONTINUED
SPRING, HELICAL, COMPRESSION: FOR LOADS BELOW 20 POUNDS
本标准规定了 形弹黄卡圈的结构、尺寸要求。 本标准适用于掖压装置壳体上安装用的滤芯盖、断流活门的肯定。
Circle spring clamp hoop
本规范规定了压缩弹簧和拉伸弹簧的技术要求 ,质量保证规定和交货准备。 本规范适用于工作温度为常温和温度不超过 500℃ 高溫的彈簧的制造和驗收。
Specification for compressed spring and tensile spring
This list has been prepared for use by or for the Government in the acquisition of products covered by the subject specification and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense
FILTER ELEMENTS, HYDRAULIC, DISPOSABLE, GENERAL SPECIFICATION FOR (METRIC)
This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMAMembers. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.
Aerospace Series Clips, Spring Tension Technical Specification Edition P 1
This Technical Report was drawn up by the Technical Committee C 8 of the AECMA Standardization Committee.
Aerospace Series Clips, Spring Tension Design Recommendations Edition 1
This Technical Report specifies the conditions of installation of spring clips for aerospace applications.
Aerospace Series Clips, Spring Tension Assembly Recommendations Edition 1
This 'Herospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMAMembers. It has been technically approved by the experts of the concerned Technical Cornmittee following comment by the Member countries.
Aerospace Series Retainers, Spring, Sheet Metal, for Self-Locking Barrel Nuts, in Corrosion Resisting Steel, Passivated Editino P 1
This "Aerospace Series" Presfandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.
Aerospace Series Clips, Spring Tension, in Alloy Steel FE-PA3903 Edition P 1
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号