Y26 日用搪瓷制品 标准查询与下载

EN ISO 4528:2015 釉瓷和搪瓷精饰.制件的釉瓷和搪瓷层试验方法的选择指南(ISO 4528:2015)

Diese Internationale Norm stellt eine Leitlinie fur die Auswahl von Prufverfahren zur Bewertung der Gebrauchseigenschaften von Emails und Emaillierungen in verschiedenen Anwendungen dar. Sie nimmt Bezug auf verfugbare Prufverfahren zur Bestimmung der Eigenschaften dieser Erzeugnisse und setzt diese Eigenschaften in Beziehung zu Anforderungen an spezifische, emaillierte Erzeugnisse. Diese Norm bezieht sich grostenteils auf Prufverfahren, die in Internationalen Normen der ISO und in Europaischen Normen beschrieben sind, und legt keine Annahmekriterien oder Grenzen der Gebrauchsfahigkeit fur die Eigenschaften fest. Diese Internationale Norm gilt fur alle emaillierten Erzeugnisse unabhangig vom Grundmetall.

Vitreous and porcelain enamel finishes - Guide to selection of test methods for vitreous and porcelain enamelled areas of articles

DB44/T 1523-2015 生活用纸常用原料种类鉴别 纤维细胞形态特征法

本标准规定了通过纤维细胞形态特征鉴别生活用纸常用原料种类的方法。 本标准适用于生活用纸。

Differentiation method of fibroblast morphological characteristics of commonly used raw materials for household paper

DIN 51191:2015 釉瓷和搪瓷. 使用砂轮的滑动摩擦磨损试验

Vitreous and porcelain enamels - Sliding friction wear test using an abrasion wheel

DIN 51179:2014 釉瓷和搪瓷. 异形表面缺陷检测和定位用低电压测试. 泥浆试验

Vitreous and porcelain enamels - Low-voltage test for detecting and locating defects on profiled surfaces - Slurry test

JIS S 6052:2014 搪瓷标志板

Porcelain-enameled marker boards

ASTM C374-14 搪瓷玻璃熔化流动性的标准试验方法(流动按钮法)

1.1 These test methods cover evaluation of the relative fusion flow characteristics of samples of a given porcelain enamel frit by comparison with an established standard for that frit. 1.2 Two test methods are included, differing only in certain details of the samples and in the apparatus and procedure for preparation of test specimens. Both test methods give equally reproducible results and provide a satisfactory basis for comparison of fusion flow of the sample with that of the established standard. 1.2.1 Test Method A employs granular particles of frit to which a bonding agent has been added. Button specimens are formed under high pressure in a hydraulic press. 1.2.2 Test Method B employs crushed, sized particles of frit to which a bonding agent has been added. Button specimens are formed in a steel mold by hand. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Fusion Flow of Porcelain Enamel Frits 40;Flow-Button Methods41;

DIN ISO 6370-2:2013 釉瓷和搪瓷.耐磨性测定.第2部分:次表面磨损后的质量损失(ISO 6370-2-2011)

Vitreous and porcelain enamels - Determination of the resistance to abrasion - Part 2: Loss in mass after sub-surface abrasion (ISO 6370-2:2011)

SN/T 3534-2013 搪瓷及玻璃器皿中砷、锑溶出量的测定 原子荧光法

本标准规定了搪瓷及玻璃器皿中砷、锑溶出量(4%乙酸)测定的原子荧光方法。本标准适用于搪瓷及玻璃器皿中砷、锑溶出量(4%乙酸)的测定。

Determination of arsenic and antimony released from enamel and glass container.Atomic fluorescence spectrometry

ASTM C283-13(2017) 瓷釉器具耐沸酸的标准试验方法

2.1 Test Method A provides the producers of porcelain enameled utensils with a quality control method of testing for resistance to boiling acid for parts randomly selected from the production line. 2.2 Test Method B provides the supplier of porcelain enamel raw materials with a laboratory method for testing the resistance of different coatings (intended for use on utensils) to boiling acid. 1.1 These test methods cover the determination of the resistance of porcelain enamel coatings used on utensils to attack by boiling acid. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Resistance of Porcelain Enameled Utensils to Boiling Acid

ASTM C283-13 搪瓷器皿耐沸腾酸腐蚀的标准试验方法

2.1 Test Method A provides the producers of porcelain enameled utensils with a quality control method of testing for resistance to boiling acid for parts randomly selected from the production line. 2.2 Test Method B provides the supplier of porcelain enamel raw materials with a laboratory method for testing the resistance of different coatings (intended for use on utensils) to boiling acid. 1.1 These test methods cover the determination of the resistance of porcelain enamel coatings used on utensils to attack by boiling acid. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Resistance of Porcelain Enameled Utensils to Boiling Acid

ASTM D7786-12 测定搪瓷形成正常光泽的性能标准试验方法

This standard may be used by paint companies and raw material suppliers to assess the interactions of primers and topcoats with respect to their ability to provide good enamel holdout. Primer/topcoat systems with the best enamel holdout will result in desirable gloss in the first coat of topcoat application.1.1 This standard provides a method for determining the holdout characteristics of a primer and topcoat coating application. A standard topcoat is used to determine the absorption characteristics of a primer. Enamel holdout can be measured as a difference in observed gloss of the topcoat over a primer, relative to the gloss of the same topcoat over a non-porous smooth surface. 1.2 The standard is written in the context that the user will be evaluating the enamel holdout characteristics of a primer. Alternatively, the standard may be used as a method to evaluate the enamel holdout characteristics of primer/topcoat system where the primer is constant and different topcoats are used as test paints. 1.3 This standard may also be used for evaluation of paints other than primers as the first coat. In this alteration the user can test the enamel holdout characteristics of a self primed topcoat, or use of any other type of paint as the primer followed by the use of a standard topcoat. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Enamel Holdout

DIN EN ISO 28706-3:2011 釉瓷和搪瓷.耐化学腐蚀性的测定.第3部分:通过使用六角形容器的碱性液体测定耐化学腐蚀性(ISO 28706-3-2008).德文版本EN ISO 28706-3-2011

This part of ISO 28706 describes a test method for the determination of the resistance of vitreous and porcelain enamelled articles to attack by alkaline liquids at temperatures between 25 °C and 95 °C. The apparatus used is a hexagonal vessel in which six enamelled specimens are simultaneously tested.

Vitreous and porcelain enamels - Determination of resistance to chemical corrosion - Part 3: Determination of resistance to chemical corrosion by alkaline liquids using a hexagonal vessel (ISO 28706-3:2008); German version EN ISO 28706-3:2011

DIN EN ISO 28706-2:2011 釉瓷和搪瓷.耐化学腐蚀性的测定.第2部分:使用沸腾酸液,沸腾中性液体和/或它们的蒸汽测定耐化学腐蚀性(ISO 28706-2-2008).德文版本EN ISO 28706-2-2011

This part of ISO 28706 describes a test method for the determination of the resistance of flat surfaces of vitreous and porcelain enamels to boiling acids, boiling neutral liquids and/or their vapours. This method allows the determination of the resistance of vitreous and porcelain enamels to the liquid and vapour phases of the corrosive medium simultaneously.

Vitreous and porcelain enamels - Determination of resistance to chemical corrosion - Part 2: Determination of resistance to chemical corrosion by boiling acids, boiling neutral liquids and/or their vapours (ISO 28706-2:2008); German version EN ISO 28706-2

DIN EN ISO 28706-1:2011 釉瓷和搪瓷.耐化学腐蚀性的测定.第1部分:室温下耐酸化学腐蚀性的测定(ISO 28706-1-2008).德文版本EN ISO 28706-1-2011

This part of ISO 28706 descirbes a test method for the determination of the resistance of vitreous and porcelain enamelled articles to attack by an acid at room temperature, and also specifies a method of classifying the results.

Vitreous and porcelain enamels - Determination of resistance to chemical corrosion - Part 1: Determination of resistance to chemical corrosion by acids at room temperature (ISO 28706-1:2008); German version EN ISO 28706-1:2011

DIN EN ISO 28706-4:2011 釉瓷和搪瓷.耐化学腐蚀性的测定.第4部分:通过使用圆柱形容器的碱性液体测定耐化学腐蚀性(ISO 28706-4-2008).德文版本EN ISO 28706-4-2011

This part of ISO 28706 describes a test method for the determination of the resistance of vitreous and porcelain enamelled articles to attack by alkaline liquids at temperatures between 25 °C and 95 °C. The apparatus used is a cylindrical vessel in which only one enamelled specimen is tested.

Vitreous and porcelain enamels - Determination of resistance to chemical corrosion - Part 4: Determination of resistance to chemical corrosion by alkaline liquids using a cylindrical vessel (ISO 28706-4:2008); German version EN ISO 28706-4:2011

BS EN ISO 28706-5:2011 釉瓷和搪瓷.耐化学腐蚀性的测定.封闭系统中耐化学腐蚀性的测定

This part of ISO 28706 specifies a test method for the determination of the resistance of vitreous- and porcelain-enamelled articles to attack in closed systems by acid, neutral and alkaline liquids, as well as by actual process mixes. It applies primarily to the testing of enamels designed for use in chemical processes.

Vitreous and porcelain enamels. Determination of resistance to chemical corrosion. Determination of resistance to chemical corrosion in closed systems

BS EN ISO 28706-2:2011 釉瓷和搪瓷.耐化学腐蚀性的测定.使用沸腾酸液,沸腾中性液体和/或其蒸汽测定耐化学腐蚀性

This part of ISO 28706 describes a test method for the determination of the resistance of flat surfaces of vitreous and porcelain enamels to boiling acids, boiling neutral liquids and/or their vapours. This method allows the determination of the resistance of vitreous and porcelain enamels to the liquid and vapour phases of the corrosive medium simultaneously.

Vitreous and porcelain enamels. Determination of resistance to chemical corrosion. Determination of resistance to chemical corrosion by boiling acids, boiling neutral liquids and/or their vapours

BS EN ISO 28706-1:2011 釉瓷和搪瓷.耐化学腐蚀性的测定.室温下耐酸化学腐蚀性的测定

This part of ISO 28706 describes a test method for the determination of the resistance of vitreous and porcelain enamelled articles to attack by an acid at room temperature, and also specifies a method of classifying the results.

Vitreous and porcelain enamels. Determination of resistance to chemical corrosion. Determination of resistance to chemical corrosion by acids at room temperature

BS EN ISO 28706-4:2011 釉瓷和搪瓷.耐化学腐蚀性的测定.用圆柱形容器测定耐碱液化学腐蚀性

This part of ISO 28706 describes a test method for the determination of the resistance of vitreous and porcelain enamelled articles to attack by alkaline liquids at temperatures between 25 °C and 95 °C. The apparatus used is a cylindrical vessel in which only one enamelled specimen is tested.

Vitreous and porcelain enamels. Determination of resistance to chemical corrosion. Determination of resistance to chemical corrosion by alkaline liquids using a cylindrical vessel

BS EN ISO 28763:2011 釉瓷和搪瓷.空气与气体和气体与气体热交换器用交流换热,上釉和包装的板材.规格

This International Standard specifies the minimum requirements and the functional characteristics of enamel coatings applied by any process, such as wet dipping, wet flow-coating, wet spraying, wet electrostatic spraying, wet electrodeposition or dry-powder electrostatic spraying, to profiled steel heat exchanger panels in regenerative heat exchangers, before and after packing in baskets. For very severe service conditions, or to obtain extended operational life, more stringent limits may be agreed between customer and supplier.

Vitreous and porcelain enamels. Regenerative, enamelled and packed panels for air-gas and gas-gas heat exchangers. Specifications