Y56 体育用品 标准查询与下载

ASTM F1890-11 测量垒球球棒性能因数的标准试验方法

This test method offers a laboratory means to compare the performance of a softball bat. Use of this test method can provide sports governing bodies a means to compare calculated BBS and other physical properties of bats.1.1 This test method covers a method for determining bat performance by measuring the bat-ball coefficient of restitution (BBCOR), deriving the bat performance factor (BPF) and calculating a batted ball speed (BBS). It is applicable to softball bats of any construction or material. The method provides a quantitative measure of bat dynamic performance that may be used for comparison purposes. 1.2 The BBCOR, BPF, and BBS are each calculated from measurements taken in the laboratory on test equipment meeting the requirements defined in this specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Test Method for Measuring Softball Bat Performance Factor

ASTM F1544-11 测定复合弓箭评价速度的标准规范

This specification will be used to determine a velocity under standard test conditions for rating an archery bow.1.1 This specification covers the testing technique to determine the rating velocities of a compound bow. 1.2 This specification will provide only a certification of performance, that is, the velocities at which a given bow will launch arrows of specified weights under standard conditions. 1.3 This specification is not intended to provide any engineering or structural evaluation of the bow that would determine its fitness for the use intended, safe function, or any other attribute except as stated. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Determining the Rating Velocities of a Compound Archery Bow

ASTM F1881-11 测量棒球球棒性能因数的标准试验方法

This test method offers a laboratory means to compare the relative performances of baseball bats. Use of this test method can provide sports governing bodies a means to compare calculated batted-ball speed and other physical properties of the bats.1.1 This test method defines a method for determining bat performance by measuring the bat-ball coefficient of restitution (BBCOR), deriving the bat performance factor (BPF), and calculating batted-ball speed (BBS). It is applicable to baseball bats of any construction or material. The test method provides a quantitative measure of bat dynamic performance that may be used for comparison purposes. 1.2 The BBCOR, BPF, and BBS are each calculated from measurements taken in the laboratory on test equipment meeting the requirements defined in this test method. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Baseball Bat Performance Factor

ASTM F2772-11 室内运动地板系统运动性能的标准规格

1.1 This specification establishes levels for athletic performance properties of multi-purpose indoor sports floor systems, excluding turf and materials specific to running tracks and tennis courts. 1.2 The methods described are applicable in both the laboratory and field unless otherwise stated. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Athletic Performance Properties of Indoor Sports Floor Systems

ASTM F1436-11 弓射箭弦中心工作直径尺寸规格的标准指南

This guide is not meant to be all inclusive since there are, and will continue to be, special circumstances that will dictate the use of nonconforming dimensions. These special circumstances and the requirements that they establish cannot be totally anticipated and therefore must be treated individually. These guidelines are based on an analysis of presently used materials for the manufacture of bow strings and the strength requirements dictated by archery bows falling within a draw weight range of 0 to 100 lb (0 to 444.8 N). These guidelines also address the desirability of proper fit of the arrow nock to the center serving.1.1 This guide covers the formulation of preliminary guidelines for the outside diameter dimensions of the center servings for the shooting strings for archery bows.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Guide for Center Serving Diameter Dimensions for Archery Bow Strings

ASTM F472-11 高山滑雪板的几何标准术语

A standard set of definitions is needed to allow manufacturers, consumers, retailers, and scientists to use a common language in describing Alpine skis.1.1 This terminology covers the terms required to describe the geometry of Alpine skis and does not cover special purpose skis. 1.2 The terms are presented in a sequence considered to be the most logical, with definitions presented later calling upon those presented earlier.

Standard Terminology for Geometry of Alpine Skis

ASTM F1853-11 睡袋容积测量的标准试验方法

This test method can be used to quantify and compare packing volumes of sleeping bags. It defines the volume occupied by a sleeping bag under a standardized load (see 4.2).1.1 This test method covers the quantitative volume of a sleeping bag in a cylinder under a standardized load. 1.2 This test method uses a physical volumetric measurement applicable in the laboratory or in the field. 1.3 The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Sleeping Bag Packing Volume

ANSI/ASTM F2040:2011 雪上娱乐运动用头盔的规范

Specification for Helmets Used for Recreational Snow Sports

ASTM F2398-11 测量棒球或垒球棒的转动惯量和冲击中心的标准试验方法

This test method offers a laboratory means to measure the inertial properties of bats, specifically weight, balance point, center of percussion, and MOI, in support of other test methods including the ASTM standards referenced in this document. Use of this test method can provide sports governing bodies the means to establish rules regarding the physical properties of bats, specifically MOI. 1.1 Method for determining the moment of inertia (MOI), the center of percussion (COP), and the balance point (BP) of baseball and softball bats. These physical properties are used in Test Method F1881, Test Method F1890, and Test Methods F2219. 1.2 The MOI, COP, and BP are measured in the laboratory on test equipment meeting the requirements defined in this test method. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Moment of Inertia and Center of Percussion of a Baseball or Softball Bat

ASTM F2569-11 体育运动用表面压力还原性能评估的标准试验方法

The force reduction property is just one of the important properties of a surface used for athletic activity. It may be an indicator of the performance, safety, comfort, or suitability of the surface. Manufacturers of athletic surfaces may use this test method to evaluate the effects of design changes on the impact forces generated on the surface. Facility owners may use this standard to evaluate the performance of existing sport/athletic surfaces. Results may be useful during the selection process for a replacement surface, or for an additional athletic surface being added to the facility. Facility owners may also use this test method to verify that newly installed surfaces perform at or near the levels included in project specifications. 1=drop mass and striker 2=guide rod 3=spring 4=upper end-cap 5=bottom end-cap 6=test foot 7=adjustable support 8=height adjustment and release mechanism 9=load cell 10=housing sleeve 11=guide holeFIG. 1 Force Reduction Test Apparatus1.1 This test method covers the quantitative measurement and normalization of impact forces generated through a mechanical impact test on an athletic surface. The impact forces simulated in this test method are intended to represent those produced by lower extremities of an athlete during landing events on sport or athletic surfaces. 1.2 This test method may be applied to any surface where athletic activity may be conducted.

Standard Test Method for Evaluating the Force Reduction Properties of Surfaces for Athletic Use

ASTM F1064-11 租用的全套和非全套高山滑雪板/滑雪靴固定装置/滑雪靴设备的抽样和检验用标准操作规程

The purpose of this practice is to aid in providing the end user with an appropriate functioning system and release/retention value by providing the rental facility with an ongoing program for monitoring the appropriateness of functional characteristics of the system. It is assumed that these procedures are integrated into the maintenance and operating procedures specified by the equipment manufacturers. This practice is not intended to create additional or redundant requirements for the rental facility. However, this practice should be the basis for the development of rental procedures if the equipment manufacturer's maintenance and operating procedures do not specifically state that they are in compliance with this practice. This practice will aid the rental facility in providing the end user with an appropriate release/retention value. This practice is applicable to rental facilities that use releasable Alpine ski bindings. It is not intended as a method for evaluating equipment design.1.1 This practice establishes a uniform method for the sampling and inspection of complete and incomplete Alpine ski/binding/boot systems used in rental operations. This practice is appropriate for use in rental applications in which all or part of the functional components of the system are supplied by the rental facility. 1.2 This practice should be followed by any facility that rents complete or incomplete Alpine ski/binding/boot systems to an end user. Note 18212;Refer to Practice F1063 for equivalent procedures and tolerances for retail systems.

Standard Practice for Sampling and Inspection of Complete and Incomplete Alpine Ski/Binding/Boot Systems in Rental Applications

ANSI/ASTM F1853:2011 睡袋容积测量的试验方法

Test Method for Measuring Sleeping Bag Packing Volume

ASTM F803-11 特定体育项目用眼镜保护装置的标准规范

1.1 This specification covers eye protectors, designed for use by players of racket sports, women's lacrosse, field hockey, basketball, baseball, and soccer that minimize or significantly reduce injury to the eye and adnexa due to impact and penetration by racket-sport rackets and balls, women's lacrosse and field hockey sticks and balls, baseballs, soccer balls, hands, elbows, and fingers. Protective eyewear offers protection only to the eyes and does not protect other parts of the head. 1.2 Protectors are divided into three types depending on their design characteristics. 1.3 This specification applies to eye protectors for use by wearers of corrective lenses and also by those players who do not require prescription eyewear. (Warning8212;Polycarbonate spectacle lenses should be used if spectacles are worn under protective eyewear.) 1.4 In this standard, the use of the words “shall” or “must” indicates a mandatory requirement. The word “should” indicates a recommendation. 1.5 Failure of the product occurs when the protector is unable to meet the general, mechanical, and optical (if applicable) requirements of the standard. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.7 The following precautionary caveat pertains only to the test methods portions, Sections 9-11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Eye Protectors For Selected Sports

ASTM F2040-11 雪上娱乐运动用头盔标准规范

1.1 This specification defines performance requirements for helmets used in nonmotorized recreational snow sports (such as skiing, snowboarding, and other alpine sports). This specification is a performance standard and is not intended to restrict design. Although a helmet that meets this specification will help reduce the risk of some types of injuries to the head at slower speeds, the protection is limited. The user is responsible for participating in the sport within his/her abilities and the nature of the snow conditions which may vary widely. Compliance with the common sense rules of the sport's safety, including any applicable responsibility codes, is essential to help reduce the risk of personal injury. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. 1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed the standard and should not be sold with any indication that it meets parts of the standard.

Standard Specification for Helmets Used for Recreational Snow Sports

ASTM F2856-11 储存和安全搬运小彩弹球柱体的标准操作规程

1.1 This practice is intended to satisfy the demand for information on the basic procedures for the safe handling and transfilling of small (not bulk) paintball CO2 cylinders commonly used with a paintball marker for propulsion of a paintball. This standard does not address issues dealing with the transfilling, storage, and handling of supply cylinders that may be used in transfilling smaller cylinders. 1.2 The CO2 fill procedures are written for the pressure cycling cylinder transfilling method most commonly used by paintball field and/or store operators. 1.3 This practice should not be confused with federal, state, provincial, or municipal specifications or regulations; insurance requirements; or national safety codes. 1.4 This practice does not purport to address all of the safety problems, if any, associated with the safe handling and transfilling of small paintball cylinders. It is the responsibility of the user of this standard to establish appropriate safety practices and determine the applicability of regulatory limitations, such as and not limited to DOT, CGA, and OSHA, prior to use.

Standard Practice for Transfilling and Safe Handling of Small Paintball Cylinders

ASTM F2844-11 垒球和棒球球棒桶的位移压力的标准试验方法

This test method offers a means to compare the barrel compression of softball and baseball bats. This test is not intended for wood or solid bats.1.1 This test method describes a comparative measurement method for determining the compression force of softball and baseball bat barrels as defined by a static compression displacement test. 1.2 This standard is not intended to define the performance of softball or baseball bats but to determine the intrinsic barrel compression of a specific bat. 1.3 This standard can be used to compare the relative barrel compression force of bats using a relatively slow, non-impact loading rate. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Displacement Compression of Softball and Baseball Bat Barrels

ASTM F1750-11 彩弹球枪加螺纹推进装置接口标准规范

1.1 This specification covers the male and female threaded connectors used to interface a propellant source with a working pressure of 10 342 kPa (1800 psig) or less to a paintball marker. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specification for Paintball Marker Threaded-Propellant Source Interface

KS G 5745-2010 越野滑雪

이 표준은 눈 위를 활주하는 것을 목적으로 하는 크로스컨트리 스키(이하 스키라 한다.)에서

Crosscountry skis

DIN EN 1938:2010 人员眼睛保护.摩托车和机动脚踏两用车驾驶员用防护镜

Personal eye protection - Goggles for motorcycle and moped users; German version EN 1938:2010

KS G 7009-2010 潜水用具.压缩空气标准

이 표준은 주로 레저용으로 스쿠버 다이빙에 사용하는 개방식 스쿠버의 호흡용 압축 공기(이하

Compressed air for scuba diving