Y71 建筑五金 标准查询与下载

DIN EN 1303:2005 建筑五金.锁用圆柱形锁芯.要求和试验方法

This European Standard applies to cylinders for such locks as are normally used in buildings and are designed to be used with cylinders. This European Standard specifies performance and other requirements for the strength, security, durability, performance and corrosion resistance of cylinders and their original keys. It establishes two categories of use based on performance tests and five grades of security based on design requirements and on performance tests that simulate attack.#,,#

Building hardware - Cylinders for locks - Requirements and test methods; German version EN 1303:2005

BS EN 1303:2005 建筑五金.锁芯.要求和试验方法

This document applies to cylinders for locks normally used in buildings, which are designed to be used with cylinders. This document specifies performance and other requirements for the strength, security, durability, performance and corrosion resistance of cylinders and their original keys. It establishes one category of use, three categories of durability, two categories each for fire and corrosion resistance all based on performance tests as well as six grades of key related security based on design requirements and three grades on performance tests that simulate attack. This document includes tests of satisfactory operation at temperatures between - 20 ℃ and + 80 ℃. It specifies test methods to be used on cylinders and their protective measures linked with these cylinders and recommended by the manufacturer. Corrosion resistance is specified by reference to the requirements of the European Standard EN 1670 on the protection of corrosion for locks and building hardware, see annex B. The suitability of cylinders for use on fire or smoke-door assemblies is determined by fire performance tests conducted in addition to the performance testing required by this standard. Since suitability for use on fire doors is not essential in every situation, the manufacturer has the option to state if the cylinder conforms to these additional requirements or not. Unless otherwise specified cylinders shall conform to the requirements specified in the relevant European Standard EN 1634-1 or prEN 1634-2, see annex A. Assessment of fire resistance of grade 1 doors is beyond the scope of this document. On occasions there may be a need for additional functions within the design of the cylinder. Purchasers should satisfy themselves that the products are suitable for their intended use.

Building hardware - Cylinders for locks - Requirements and test methods

JIS A 5508:2005 钉子

この規格は，主として一般に使用される手打用くぎ及び自動くぎ打機用のくぎ()について規定する。ただし，自動くぎ打機用として連結するための材料及びその方法については規定しない。 注()自動くぎ打機用のくぎとは，プラスチック，紙，針金，のりなどを用いて連結されろくぎをいう。

Nails

QB/T 2697-2005 地弹簧

本标准规定了地弹簧的产品分类、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于安装在平开门扇下可单、双向开门、使用温度在-15℃～40℃、由金属弹簧、液压阻尼组合作用的各种地弹簧。

Floor spring

QB/T 2698-2005 闭门器

本标准规定了闭门器的产品分类、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于安装在平开门扇上部、单向开门、使用温度在-15℃～40℃、由金属弹簧、液压阻尼组合作用的各种闭门器。

Door closer

SN/T 1534-2005 出口呆舌门锁检验规程

本标准规定了出口呆舌门锁的技术要求、抽样、检验及检验结果的判定。 本标准适用于出口呆舌门锁的检验，不适用于其他门锁。

Rule of inspection of doorlocks with dead bolt for export

DIN 18267:2005 窗把手.弹簧锁和可锁窗把手

This standard defines requirements and test methods for cklickable, cklickable and latchable and clickable and lockable window handles.#,,#

Window handles - Clickable and lockable window handles

ASTM F1577-05 双开式弹簧门安全锁的标准试验方法

A major concern for detention and correctional administrative officials is the reliable operation of locks used in their facilities. These test methods aid in assigning a level of physical security and performance to locks for swinging door assemblies. These test methods evaluate the resistance of a lock to attacks using battering devices, prying devices, and fire. These test methods also evaluate the performance of a lock under simulated operating conditions. These test methods do not provide a measure of the resistance or performance of a lock subjected to attack by chemical agents, ballistics, explosives, or other extreme methods of attack. These test methods do not measure the resistance or performance of the device when subjected to environmental elements such as rain, snow, or wind-carried dust or sand. Where such elements may be a factor, the manufacturer should be consulted for proper application. The primary purpose of these test methods is to approximate the levels of abuse and operating conditions to which locks are subjected in detention and correctional institutions. The desired result of these test methods will provide a measure of assurance of protection to the correctional personnel, public, and inmates. It is recommended that the detention/correctional facility administration provide adequate training, supervision, and preventative maintenance programs to enable door assemblies to function as intended throughout the expected service life.1.1 These test methods cover the apparatus, procedures, and acceptance conditions for evaluating the normal operational performance and the performance characteristics under assault conditions of locks used in swinging door assemblies in detention and correctional institutions. Thus, they give only an indication of the performance characteristics of locks in actual service. Such variables as installation and maintenance conditions are not considered.1.2 It is the intent of these test methods to help ensure that detention locks perform at or above minimum acceptable levels to control passage to unauthorized or secure areas, to confine inmates, and to delay and frustrate escape attempts and resist vandalism. It is recognized that in order to meet the intent of these test methods, door and frame assemblies must be compatible with the level of performance required by Test Method F 1450.1.3 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Detention Locks for Swinging Doors

ASTM F1643-05 安全滑动门锁装置组件的标准试验方法

A major concern for detention and correctional administrative officials is the reliable operation of sliding devices used in their facilities. These test methods aid in assigning a level of physical security and performance to devices for sliding door assemblies. These test methods evaluate the resistance of a sliding door assembly to attacks using battering devices, prying devices, smoke, and fire. These test methods also evaluate the performance of a sliding device under simulated operating conditions. These test methods do not provide a measure of the resistance or performance of the device subjected to attack by chemical agents, ballistics, explosives, or other extreme methods of attack. These test methods do not measure the resistance or performance of the device when subjected to environmental elements such as humidity, temperature, rain, snow, or wind-carried dust or sand. Where such elements may be a factor the manufacturer should be consulted for proper application. The primary purpose of these test methods is to approximate the levels of abuse and operating conditions to which devices are subjected in detention and correctional institutions. The result of these test methods will provide a measure of assurance of protection to the correctional personnel, public, and inmates. Preventative maintenance programs shall be provided in accordance with the manufacturerrsquo;recommendation to enable sliding device assemblies to function as intended throughout the expected service life. These test methods do not measure the performance or cycle life of the local or remote mechanical emergency release mechanism, or both, due to their design variables and low user requirements.1.1 These test methods cover the apparatus, procedures, and acceptance conditions for evaluating the normal operational performance and the performance characteristics under assault, smoke, and fire conditions of sliding device assemblies in detention and correctional institutions. These test methods give an indication of the performance characteristics of devices in actual service. Such variables as installation and maintenance conditions are not considered.1.2 It is the intent of these test methods to help ensure that detention sliding devices perform at or above minimum acceptable levels to control passage to unauthorized or secure areas, to confine inmates and to delay and frustrate escape attempts and resist vandalism. However, these test methods do not address door construction. It is recognized that in order to meet the intent of these test methods, door assemblies shall be compatible with the level of performance required by Test Methods F 1450.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Detention Sliding Door Locking Device Assembly

ASTM F1758-05 安全等级双开式弹簧门用安全铰链的标准试验方法

A major concern for detention and correctional administrative officials is the reliable operation of hinges used in their facilities. These test methods aid in assigning a level of physical security and performance to hinges for swinging door assemblies. These test methods evaluate the effect on hinges of battering attacks on the door simulating assault conditions as well. These test methods also evaluate the performance of a hinge under simulated normal operation. These test methods do not provide a measure of the resistance or performance of a hinge to attack by the following: chemical agents, ballistics, explosives, or other extreme methods of attack, such as direct impact or manipulation on the hinges or to environmental elements such as rain, snow, or wind-carried dust or sand. Where such elements are a potential factor, consult the manufacturer. The primary purpose of these test methods is to approximate the levels of abuse conditions and normal operating conditions to which hinges are subjected in detention and correctional institutions. These test methods attempt to do this through the different grade levels associated with cycle and impact testing. The desired result of these test methods will provide a measure of assurance of protection to the correctional personnel, public, and inmates.1.1 These test methods cover the apparatus, procedures, and acceptance conditions for evaluating the normal operating performance characteristics and the performance characteristics under assault conditions of hinges used in swinging door assemblies in detention and correctional institutions. These types of hinges are described in detail in , , and . Thus, these test methods only give an indication of the performance characteristics of hinges in actual service. Such variables as installation and maintenance conditions which have a potential impact on performance characteristics are not considered.1.2 It is the intent of these test methods to help ensure that detention hinges (reference to hinges is inclusive of a continuous hinge) perform at or above minimum acceptable levels to confine inmates, to delay and frustrate escape attempts, and to resist vandalism and assault conditions. It is recognized that in order to meet the intent of these test methods, door, frame and lock assemblies must be compatible with the level of performance required by Test Methods F 1450 and F 1577.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.1.4 Consult NFPA 80 for Fire Doors Windows concerning hinge requirements on fire doors.

Standard Test Methods for Detention Hinges Used on Detention-Grade Swinging Doors

ASTM F1758-05(2012) 安全等级双开式弹簧门用安全铰链的标准试验方法

A major concern for detention and correctional administrative officials is the reliable operation of hinges used in their facilities. These test methods aid in assigning a level of physical security and performance to hinges for swinging door assemblies. These test methods evaluate the effect on hinges of battering attacks on the door simulating assault conditions as well. These test methods also evaluate the performance of a hinge under simulated normal operation. These test methods do not provide a measure of the resistance or performance of a hinge to attack by the following: chemical agents, ballistics, explosives, or other extreme methods of attack, such as direct impact or manipulation on the hinges or to environmental elements such as rain, snow, or wind-carried dust or sand. Where such elements are a potential factor, consult the manufacturer. The primary purpose of these test methods is to approximate the levels of abuse conditions and normal operating conditions to which hinges are subjected in detention and correctional institutions. These test methods attempt to do this through the different grade levels associated with cycle and impact testing. The desired result of these test methods will provide a measure of assurance of protection to the correctional personnel, public, and inmates.1.1 These test methods cover the apparatus, procedures, and acceptance conditions for evaluating the normal operating performance characteristics and the performance characteristics under assault conditions of hinges used in swinging door assemblies in detention and correctional institutions. These types of hinges are described in detail in 3.1.6, 3.1.9, and 3.1.22. Thus, these test methods only give an indication of the performance characteristics of hinges in actual service. Such variables as installation and maintenance conditions which have a potential impact on performance characteristics are not considered. 1.2 It is the intent of these test methods to help ensure that detention hinges (reference to hinges is inclusive of a continuous hinge) perform at or above minimum acceptable levels to confine inmates, to delay and frustrate escape attempts, and to resist vandalism and assault conditions. It is recognized that in order to meet the intent of these test methods, door, frame and lock assemblies must be compatible with the level of performance required by Test Methods F1450 and F1577. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. 1.5 Consult NFPA 80 for Fire Doors & Windows concerning hinge requirements on fire doors.

Standard Test Methods for Detention Hinges Used on Detention-Grade Swinging Doors

QB/T 1334-2004 水嘴通用技术条件

本标准规定了水嘴(水龙头)的定义、产品分类、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于公称通径为DN15、DN20、DN25，公称压力1.0MPa，介质温度不大于90℃条件下使用的，安装盥洗室(洗手间、浴室等)、厨房和化验室等卫生设施上各种结构的水嘴。

Universal technical terms for faucets

CJ/T 193-2004 内层熔接型铝塑复合管

Internal layer thermo-fusion polyolefin/aluminum/polyolefin composite pipe

NF P26-306:2004 建筑五金.细木工用片式合页.总则、术语、分类和尺寸

Building hardware - Paumelles hinges with leaves for woodword - General, terminology, classification and dimensions.

BS DD CEN/TS 13126-2:2004 建筑五金、窗户和门上窗的配件.要求和试验方法.窗销把手

Building hardware, fittings for windows and door height windows - Requirements and test methods - Part 2:Casement fastener handles

PD CEN/TS 13126-6:2004 建筑五金件、窗和门上窗用配件 要求和试验方法 第6部分 可变几何支柱铰链(带或不带摩擦系统)

This Part of CEN/TS 13126 specifies the requirements and test methods for durability, strength, security and function of mechanically operated variable geometry stay hinges (with or without a friction system). NOTE 1 Balancing stay arms / hinges do not represent a friction system. NOTE 2 For the purpose of this standard the friction system is achieved by friction pads or similar.

Building hardware, fittings for windows and door height windows - Requirements and test methods - Part 6: Variable geometry stay hinges (with or without a friction system)

BS DD CEN/TS 13126-17:2004 建筑五金、窗户和门上窗的配件.要求和试验方法.倾斜和滑动系统配件

Building hardware, fittings for windows and door height windows - Requirements and test methods - Part 17:Fittings for tilt and slide systems

BS DD CEN/TS 13126-16:2004 建筑五金、窗户和门上窗的配件.要求和试验方法.提升和滑动系统配件

Building hardware, fittings for windows and door height windows - Requirements and test methods - Part 16:Fittings for lift and slide systems

BS DD CEN/TS 13126-15:2004 建筑五金、窗户和门上窗的配件.要求和试验方法.滑轮

Building hardware, fittings for windows and door height windows - Requirements and test methods - Part 15:Rollers

BS DD CEN/TS 13126-14:2004 建筑五金、窗户和门上窗的配件.要求和试验方法.窗扇扣件

Building hardware, fittings for windows and door height windows - Requirements and test methods - Part 14:Sash fasteners