Z13 固体废弃物、土壤及其他环境要素采样方法 标准查询与下载

ASTM D5438-00 化学分析用地板尘埃采集的标准实施规程

1.1 This practice covers a procedure for the collection of a sample of dust from carpets and bare floors that can be analyzed for lead, pesticides, or other chemical compounds and elements. 1.2 This practice is applicable to a variety of carpeted and bare floor surfaces. It has been tested for level loop and plush pile carpets and bare wood floors, specifically. 1.3 This practice is not intended for the collection and evaluation of dust for the presence of asbestos fibers. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Collection of Floor Dust for Chemical Analysis

XP X30-403-1999 废品.硅酸盐玻璃.通过蒸发和浓缩在一封闭环管内重新产生的,不断更新的含水溶液的接触中初始溶解速度的测定试验

Waste - Silicate glass - Test for determination of the initial dissolution velocity on contact with a regularly renewed aqueous solution, regenerated within a closed circuit by evaporation and condensation.

CJ/T 103-1999 城市生活垃圾.全氮的测定.半微量开氏法

Municipal domestic refuse.Determination of total nitrogen.Semi-micro Kjeldahl method

CJ/T 100-1999 城市生活垃圾.镉的测定.原子吸收分光光度法

本标准规定了用原子吸收分光光度法测定福含量的原理、仪器、试剂和操作步骤。 本标准适用于城市生活垃圾中福的测定。

Municipal domestic refuse.Determination of cadmium.Atomic absorption spectrophotometric method

CJ/T 101-1999 城市生活垃圾.铅的测定.原子吸收分光光度法

Municipal domestic refuse.Determination of lead.Atomic absorption spectrophotometric method

CJ/T 102-1999 城市生活垃圾.砷的测定.二乙基二硫代氨基甲酸银分光光度法

Municipal domestic refuse.Determination of arsenic.Spectrophotometric method with silver diethyldithiocarbamate

CJ/T 105-1999 城市生活垃圾.全钾的测定.火焰光度法

Municipal domestic refuse.Determination of total potassium.Flame spectrophotometric method

CJ/T 104-1999 城市生活垃圾.全磷的测定.偏钼酸铵分光光度法

Municipal domestic refuse.Determination of total phosphorus.Ammonium metamolybdate spectrophotometric method

CJ/T 96-1999 城市生活垃圾.有机质的测定.灼烧法

Municipal domestic refuse.Determination of organic matter.Ignition method

CJ/T 97-1999 城市生活垃圾.总铬的测定.二苯碳酰二肼比色法

Municipal domestic refuse.Determination of total chromium.Diphenyl carbazide color method

CJ/T 98-1999 城市生活垃圾.汞的测定.冷原子吸收分光光度法

Municipal domestic refuse.Determination of mercury.Cold atomic absorption spectrophotometric method

CJ/T 99-1999 城市生活垃圾.pH的测定.玻璃电极法

Municipal domestic refuse.Determination of pH.Glass electrode method

ISO 11268-3:1999 土壤质量 污染物对蚯蚓的影响 第3部分:野外影响的测定指南

This part of ISO 11268 describes techniques for determining the effects of substances on earthworms in the field, and provides a basis for determining the effects of chemicals applied to, or incorporated into, soil.

Soil quality - Effects of pollutants on earthworms - Part 3: Guidance on determination of effects in field situations

ISO 11267:1999 土壤质量 土壤污染对弹尾目(Folsomia candida)的再生抑制

This International Standard describes a method for determining the effects of substances on the reproduction of Folsomia Candida by dermal and alimentary uptake in a defined artificial soil substrate. The method is not applicable to volatile substances, i.e. substances for which H (Henry's constant) or the air/water partition coefficient is greater than 1, or for which the vapour pressure exceeds 0,013 3 Pa at 25 ℃. NOTE 1 The stability of the test substance cannot be assured over the test period. No allowance is made in the test method described for possible degradation of the test substance over the course of the experiment.. NOTE 2 Recommendations for adapting the method for comparing or monitoring soil quality are given in annex E.

Soil Quality - Inhibition of Reproduction of Collembola (Folsomia Candida) by Soil Pollutants (Second Edition)

ASTM E1729-99 用原子能谱测定技术对铅测定用干涂料样品现场采集的标准实施规程

1.1 This practice covers the collection of dried paint samples or other coatings from buildings and related structures. These samples are collected in a manner that will permit subsequent digestion and determination of lead using laboratory analysis techniques such as Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) and Flame Atomic Absorption Spectrometry (FAAS). 1.2 This practice is used to collect samples for subsequent determination of lead on an area basis (milligrams of lead per area sampled) or concentration basis (milligrams of lead per gram of dried paint collected or weight percent). 1.3 This practice does not address the sampling design criteria (that is, sampling plan that includes the number and location of samples) that are used for risk assessment and other purposes. To provide for valid conclusions, sufficient numbers of samples must be obtained as directed by a sampling plan. 1.4 This practice contains notes that are explanatory and are not part of the mandatory requirements of this practice. 1.5 The values stated in SI units are to be regarded as the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Field Collection of Dried Paint Samples for Lead Determination by Atomic Spectrometry Techniques

BS EN 12176:1998 污泥的特性记述.pH值的测定

The scope of this standard is the sludges, i.e. and sludges products from: —storm water handling; —night soil; —urban wastewater collecting systems; —urban wastewater treatment plants; —treating industrial wastewater similar to urban wastewater (as defined in Directive 91/271 EEC); —water supply treatment plants; —water distribution systems; —but excluding hazardous sludges from industry. This method is applicable to the determination of pH values of sludges which include liquid, paste-like or solid matter. If the sludge sample is sufficiently liquid, direct measurement should be made. If the sludge sample contains relatively high percentages of solids the measurement should be carried out after dilution with water.

Characterization of sludge - Determination of pH value

ISO 11632:1998 固定源排放 二氧化硫质量浓度的测定 离子色谱法

This International Standard specifies a method for the determination of the mass concentration of sulfur dioxide emitted from combustion facilities and technical processes, and defines the most important performance characteristics. The method described in this International Standard has been tested for a sulfur dioxide concentration range of 6 mg/m to 333 mg/m with sampling periods of 30 min. It is applicable to mass concentrations of sulfur dioxide exceeding this range by carrying out an appropriate dilution of the sample solutions prior to the analysis or by using larger volumes of absorption solution, and to sulfur dioxide concentrations below this range by extending the sampling period. This International Standard is applicable to the analysis of samples containing negligible levels of sulfur trioxide and volatile sulfates (< 5 % of the expected sulfur dioxide concentration), and ammonia (< 5 mg/m). All concentrations are based on dry gas at a temperature of 273,2 K and pressure of 101,3 kPa.

Stationary source emissions - Determination of mass concentration of sulfur dioxide - Ion chromatography method

HJ/T 20-1998 工业固体废物采样制样技术规范

本规范规定了工业固体废物采样制样方案设计、采样技术、制样技术、样品保存和质量控制。 本规范适用于工业固体废物的特性鉴别、环境污染监测、综合利用及处置等所需样品的采集和制备。 本规范不适用于放射性指标监测的采样制样。

Technical specifications on sampling and sample preparation from industry solid waste

ASTM D6050-97(2003)e1 有机液体有害废物中不溶固体测定的标准试验方法

Facilities utilizing bulk liquid hazardous waste fuels are concerned about material handling characteristics and the overall quality of the fuel. A high percentage of insoluble, suspended solid material can create pumping, filtering, or grinding difficulties in the off-loading of bulk shipments of OLHW and can contribute to excessive wear on processing equipment. High solids can also decrease the quality and consistency of commingled fuel by decreasing the effectiveness of agitation in storage tanks.1.1 This test method covers the determination of the approximate amount of insoluble, suspended solid material in organic liquid hazardous waste (OLHW). 1.2 This test method is intended to be used in approximating the amount of insoluble, suspended solids in determining the material handling characteristics and fuel quality of OLHW. It is not intended to replace more sophisticated procedures for the determination of total solids. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Insoluble Solids in Organic Liquid Hazardous Waste

ASTM D6050-97 有机液体有害废物中不溶固体测定的标准试验方法

1.1 This test method covers the determination of the approximate amount of insoluble, suspended solid material in organic liquid hazardous waste (OLHW). 1.2 This test method is intended to be used in approximating the amount of insoluble, suspended solids in determining the material handling characteristics and fuel quality of OLHW. It is not intended to replace more sophisticated procedures for the determination of total solids. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Insoluble Solids in Organic Liquid Hazardous Waste