Z60 污染物排放综合 标准查询与下载

BS EN 14997:2015 废物的表征 浸出行为测试 连续 pH 控制下 pH 对浸出的影响

Characterization of waste. Leaching behaviour test. Influence of pH on leaching with continuous pH control

DB33/ 962-2015 纺织染整工业大气污染物排放标准

Emission Standards of Air Pollutants for Textile Dyeing and Finishing Industry

EN 14997:2015 废弃物特性.沥滤性能测定.pH值对连续pH值控制过滤的影响

This European Standard specifies a method for the determination of the influence of pH on the leachability of inorganic constituents from a waste material. Approaching equilibrium as defined in this European Standard is established by continuous adjustment of the pH by addition of acid or base to reach desired pH values. This test method produces eluates, which are subsequently characterized physically and chemically. This European Standard is a parameter specific test as specified in EN 12920. The application of this test method alone is not sufficient for the determination of the detailed leaching behaviour of a waste under specified conditions.

Characterization of waste - Leaching behaviour tests - Influence of pH on leaching with continuous pH-control

HJ 735-2015 土壤和沉积物 挥发性卤代烃的测定 吹扫捕集/气相色谱-质谱法

本标准规定了测定土壤和沉积物中挥发性卤代烃的吹扫捕集/气相色谱-质谱法。本标准适用于土壤和沉积物中氯甲烷等35种挥发性卤代烃的测定。其他挥发性卤代烃如果通过验证也适用于本标准。当取样量为5 g时,35种挥发性卤代烃的方法检出限为0.3~0.4 μg/kg,测定下限为1.2~1.6 μg/kg。详见附录A。

Soil and sediment.Determination of volatile halohydrocarbons.Purge and trap gas chromatography mass spectrometry

DB12/ 556-2015 工业炉窑大气污染物排放标准

本标准适用于天津市辖区内现有工业炉窑主要大气污染物的排放管理，以及新建、改建、扩建项目

Air Pollutant Emission Standards for Industrial Furnaces

DIN EN 16424:2015 废弃物的特性描述. 使用便携式X射线荧光光谱仪对元素成分进行的筛选方法; 德文版本EN 16424-2014

Characterization of waste - Screening methods for the element composition by portable X-ray fluorescence instruments; German version EN 16424:2014

HJ 734-2014 固定污染源废气 挥发性有机物的测定 固相吸附-热脱附/气相色谱-质谱法

本标准规定了固定污染源废气中24种挥发性有机物测定的固相吸附-热脱附/气相色谱-质谱法。本标准适用于固定污染源废气中24种挥发性有机物的测定,24种挥发性有机物包括:丙酮、异丙醇、正己烷、乙酸乙酯、苯、六甲基二硅氧烷、3-戊酮、正庚烷、甲苯、环戊酮、乳酸乙酯、乙酸丁酯、丙二醇单甲醚乙酸酯、乙苯、对/间二甲苯、2-庚酮、苯乙烯、邻二甲苯、苯甲醚、苯甲醛、1-癸烯、2-壬酮、1-十二烯。其他挥发性有机物经过验证后也可使用本方法。当采样体积为300 ml时,本标准的方法检出限为0.001~0.01 mg/m,测定下限为0.004~0.04 mg/m。详见附录A。

Stationary source emission.Determination of volatile organic compounds.Sorbent adsorption and thermal desorption gas chromatography mass spectrometry method

HJ 733-2014 泄漏和敞开液面排放的挥发性有机物检测技术导则

本标准规定了源自设备泄漏和敞开液面排放的挥发性有机物(VOCs)的检测技术要求。规定了对设备泄漏和敞开液面等无组织排放源的VOCs的检测方法、仪器设备要求、质量保证与控制等。本导则不适用直接测定泄漏和敞开液面排放源的VOCs质量排放速率。

Guideline for the determination of volatile organic compound leaks and uncovered liquid surface emissions

HJ 732-2014 固定污染源废气 挥发性有机物的采样 气袋法

本标准规定了使用聚氟乙烯(PVF)等氟聚合物薄膜气袋手工采集温度低于150℃的固定污染源废气中挥发性有机物(VOCs)的方法。本标准适用于固定污染源废气中非甲烷总烃和部分VOCs的采样,适用于本方法的VOCs包括经实验验证可在所用的材质类型气袋中稳定保存的化合物。三种氟聚合物薄膜材质气袋保存61种VOCs的性能指标参见附录A。

Emission from stationary sources.Sampling of volatile organic compounds.Bags method

BS PD CEN/TS 13649:2014 固定源排放. 专用气体有机化合物质量浓度的测定. 溶剂萃取或者热脱附之前的吸附采样方法

Stationary source emissions. Determination of the mass concentration of individual gaseous organic compounds. Sorptive sampling method followed by solvent extraction or thermal desorption

DB43/ 968-2014 工业废水铊污染物排放标准

Discharge standard of industrial wastewater thallium pollutant

DB61/ 941-2014 关中地区重点行业大气污染物排放限值

本标准适用于关中地区现有火电、水泥、炼焦、钢铁、有色和在用燃煤锅炉的大气污染物排放管理

Air Pollutant Emission Limits of Key Industries in Guanzhong Region

DB35/T 1452-2014 合成革与人造革工业污染治理工程技术规范

本标准规定了合成革与人造革工业污染治理工程设计、施工、验收和运行的技术要求。 本标准适用于合成革与人造革工业污染治理工程，包括合成革与人造革工业企业和该专业集控区集中污染治理工程，可作为合成革与人造革工业建设项目环境影响评价、环境保护设施设计与施工、建设项目竣工环境保护验收及建成后运行与管理的技术依据。

Technical specifications for industrial pollution control engineering of synthetic leather and artificial leather

DB37/T 2538-2014 山东省污染物排放地方标准编制规范

Specifications for Compilation of Local Pollutant Discharge Standards in Shandong Province

DB37/T 2539-2014 山东省环境友好型产品技术要求地方标准编制规范

Specifications for Compilation of Local Standards for Technical Requirements of Environmentally Friendly Products in Shandong Province

PD CEN/TS 16637-2:2014 建筑产品.危险物质排放的评估.第2部分：水平动态表面浸取试验

(1) This Technical Specification specifies a Dynamic Surface Leaching Test (DSLT) which is aimed at determining the release per unit surface area as a function of time of inorganic and/or non-volatile organic substances from a monolithic, plate- or sheet-like product, when it is put into contact with an aqueous solution (leachant). The test method is not suitable for substances that are volatile under ambient conditions. (2) This test is a parameter specific test focusing on identifying and specifying parameter specific properties tested under specified conditions. It is not aimed at simulating real situations. The application of results to specific intended conditions of use may be established by means of modelling (not included in this Technical Specification). (3) The modification for granular construction products with low hydraulic conductivity (Annex A) applies for granular particles with so little drainage capacity between the grains that percolation in percolation tests and in practice is nearly impossible. (4) The test method applies to more or less regularly shaped test portions consisting of monolithic test pieces with minimum dimensions of 40 mm in all directions (volume > 64000 mm 3(64 cm 3 )). It also applies to plate- or sheet-like products with surface areas of minimum 10000 mm 2(100 cm 2 ) exposed to the leachant. Products designed to drain water (e. g. draining tiles, porous asphalt) and monolithic granular products according to CEN/TS 16637-1:2014, Table 1, are also tested by this test method. All products to be tested are assumed to maintain their integrity over a time frame relevant for the considered intended use. (5) Metals, metallic coatings and organic coatings on metals are excluded from the scope of CEN/TS 16637-2 because the principles of this test (diffusion) are not obeyed by these products. Guidance on the need for testing of these products is under consideration. (6) For some coatings (e. g. some renders with organic binders according

Construction products - Assessment of release of dangerous substances - Part 2: Horizontal dynamic surface leaching test

PD CEN/TS 16637-1:2014 建筑产品.危险物质排放的评估.第1部分：浸出试验和附加试验步骤的试验指南

This Technical Specification allows the identification of the appropriate leaching test method for the determination of the release of Regulated Dangerous Substances from construction products into soil, surface water and groundwater. This document provides a stepwise procedure for the determination of appropriate release tests, including: a) guidance for the identification of construction products potentially emitting Regulated Dangerous Substances; b) determination of the test method based on general product properties; c) choice of the test method using specific product properties. Furthermore, this Technical Specification gives general guidance for CEN Technical Product Committees on basic aspects (sampling, sample preparation and storage, eluate treatment, analysis of eluates and documentation) to be specified in the relevant product standards. Metallic products, coatings on metallic products and organic coatings for metals are not considered in the determination scheme of this Technical Specification since the test method in CEN/TS 16637-2 (tank test) is not appropriate for the testing of these construction products due to a different release mechanism (solubility control). NOTE Metallic products are excluded from the scope of CEN/TS 16637-2 because the principles of that test (diffusion) are not obeyed by these products. Metallic products have shown pH dependent solubility control, which means that metals released from the oxidation layer on the metal until the maximum possible solubility level at the prevailing pH conditions in the surrounding water is reached (more water in contact with the same metal surface means more metals released and more time does not lead to more release due to solubility control). Maximum level of release can often be reached in minutes to hours. More generally, it can be stated that expression of results for metallic surfaces in mg/(m2-s) is always "conditional", i.e. dependent on the local conditions at which the measurements wer

Construction products - Assessment of release of dangerous substances - Part 1: Guidance for the determination of leaching tests and additional testing steps

BS ISO 14385-2:2014 固定源排放. 温室气体. 自动测量系统的正在进行的质量控制

Stationary source emissions. Greenhouse gases. Ongoing quality control of automated measuring systems

BS ISO 14385-1:2014 固定源排放. 温室气体. 自动测量系统的校正

Stationary source emissions. Greenhouse gases. Calibration of automated measuring systems

DB12/ 524-2014 工业企业挥发性有机物排放控制标准

本标准适用于现有和新建排污单位废气中挥发性有机物的排放管理， 以及建设项目的环境影响评价、环境保护设施设计、竣工环境保护验收及其投产后挥发性有机物的排放管理。

Emission Control Standards for Volatile Organic Compounds in Industrial Enterprises