13.220.40;83.080.01 标准查询与下载

ISO/TR 10093:2018 塑料. 燃烧试验. 标准火源

Plastics - Fire tests - Standard ignition sources

DIN EN ISO 5659-2:2017 塑料.烟雾产生.第2部分:用独立燃烧室检验测定光密度(ISO 5659-2-2017);德文版本EN ISO 5659-2-2017

ISO 5659-2 specifies a method of measuring smoke production from the exposed surface of specimens of essentially flat materials, composites or assemblies not exceeding 25 mm in thickness when placed in a horizontal orientation and subjected to specified levels of thermal irradiance in a closed cabinet with or without the application of a pilot flame. This method of test is applicable to all plastics and may also be used for the evaluation of other materials (e. g. rubbers, textile-coverings, painted surfaces, wood and other materials)

Plastics - Smoke generation - Part 2: Determination of optical density by a single-chamber test (ISO 5659-2:2017); German version EN ISO 5659-2:2017

ISO/TR 10093:2017 塑料.燃烧试验.标准火源

Plastics - Fire tests - Standard ignition sources

BS EN ISO 5659-2:2017 塑料.生烟性测定.单烟箱光密度测定

Plastics. Smoke generation. Determination of optical density by a single-chamber test

BS EN ISO 4589-3:2017 塑料 通过氧指数测定燃烧行为 高温测试

Plastics. Determination of burning behaviour by oxygen index. Elevated-temperature test

BS EN ISO 4589-2:2017 塑料.通过氧指数测定其燃烧性.室温试验

Plastics. Determination of burning behaviour by oxygen index. Ambient-temperature test

BS EN ISO 4589-1:2017 塑料 通过氧指数测定燃烧行为 一般要求

Plastics. Determination of burning behaviour by oxygen index. General requirements

ISO 5659-2:2017 塑料.烟雾产生.第2部分:用单燃烧室试验测定光密度

Plastics - Smoke generation - Part 2: Determination of optical density by a single-chamber test

ISO 4589-1:2017 塑料.通过氧指数测定其燃烧性.第1部分:一般要求

This document specifies the general requirements for the oxygen index (OI) test which are further described in ISO 4589-2 and ISO 4589-3 as follows: of oxygen and nitrogen introduced at 23 °C ± 2 °C that will just support combustion of a material under specified test conditions; typically between 25 °C and 150 °C (although temperatures up to 400 °C can be used).

Plastics - Determination of burning behaviour by oxygen index - Part 1: General requirements

ISO 4589-3:2017 塑料.通过氧指数测定其燃烧性.第3部分:高温试验

This document specifies methods for determining the minimum volume fraction of oxygen, in a mixture with nitrogen, that will support combustion of small vertical test specimens under specified test conditions over a range of temperatures between 25 °C and 150 °C. The range of temperatures is typically between 40 °C and 150 °C. The results are defined as temperature index values at the test temperature, which is typical of the practical temperature that a plastic material can experience in an overheated service situation. Methods are provided for testing materials that are self-supporting at the test temperature in the form of vertical bars or sheet up to 10,5 mm thick. However, they are not applicable to form V which requires a supporting frame as defined in ISO 4589-2:2017, Table 2. These methods are suitable for solid, laminated or cellular materials characterized by an apparent density 100 kg/m3 or higher. The methods are also applicable to some cellular materials having an apparent density of less than 100 kg/m3. A method is provided for testing flexible sheet or film materials while supported vertically. This document also includes a method (see Annex A) for determining the temperature at which the OI of small vertical test specimens in air is 20,9 % under specified test conditions. The temperature at which this occurs is defined as the flammability temperature (FT) and the method is limited to the determination of temperatures less than 400 °C. The method is not applicable to materials having an OI of

Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated-temperature test

ISO 4589-2:2017 塑料 通过氧指数测定其燃烧性 第2部分:室温试验

Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test

BS ISO 12992:2017 塑料制品.薄膜和薄板垂直火焰蔓延的测定

Plastics. Vertical flame spread determination for film and sheet

ISO 12992:2017 塑料. 薄膜和薄板垂直火焰蔓延的测定

Plastics - Vertical flame spread determination for film and sheet

KS M ISO 9773:2016 塑料 立式软薄试样与小火焰源接触的燃烧性能测定

Plastics－Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source

JIS K 7242-2:2015 塑料.烟雾的产生.第2部分:使用单室试验测定光密度

Plastics -- Smoke generation -- Part 2: Determination of optical density by a single-chamber test

BS EN ISO 15791-1:2013 塑料. 塑料产品用中等燃烧试验的研制和应用. 通用指南

Plastics. Development and use of intermediate-scale fire tests for plastics products. General guidance

ASTM D635-14 塑料在水平状态时的燃烧速率和/或燃烧蔓延程度及燃烧时间的标准试验方法

5.1 Tests made on a material under conditions herein prescribed are of value in comparing the rate of burning or extent and time of burning characteristics, or both, of different materials, in controlling manufacturing processes, or as a measure of deterioration or change in these burning characteristics prior to or during use. Correlation with flammability under actual use conditions is not implied. 5.2 The rate of burning and other burning phenomena will be affected by such factors as density, pigments, any anisotropy of the material and the thickness of the specimen. Test data shall be compared only for specimens of similar thickness, whether comparisons are being made with the same or different materials. The rate of burning and other burning phenomena will vary with thickness. 5.3 It is feasible that sheet materials that have been stretched during processing will relax during burning and give erratic results unless they are first heated above their deflection temperature, in accordance with Test Method D648, for a time sufficient to permit complete relaxation. 5.4 Burning tests require that certain variables be arbitrarily fixed, for example, specimen size, energy source and application time, and end points. Materials will be found that are unusually sensitive to one or more of the conditions chosen for this method leading to highly variable results. Additional burning characterization by other methods is highly desirable in such cases (see Note 2). 5.5 In this procedure, the specimens are subjected to specific laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it will not always be possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this procedure. 1.1 This fire-test-response test method covers a small-scale laboratory screening procedure for comparing the relative linear rate of burning or extent and time of burning, or both, of plastics in the form of bars, molded or cut from sheets, plates, or panels, and tested in the horizontal position. Note 1: This test method, and test method A of IEC8201;60695-11-10 are technically equivalent. Note 2: For additional information on materials which do not burn to the first reference mark by this test, see Test Method D3801. 1.2 This test method was developed for polymeric materials used for parts in devices and appliances. The results are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application. The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standard applicable to such equipment.

Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

ASTM D1929-14 测定塑料着火温度的标准试验方法

4.1 Tests made under conditions herein prescribed can be of considerable value in comparing the relative ignition characteristics of different materials. Values obtained represent the lowest ambient air temperature that will cause ignition of the material under the conditions of this test. Test values are expected to rank materials according to ignition susceptibility under actual use conditions. 4.2 This test is not intended to be the sole criterion for fire hazard. In addition to ignition temperatures, fire hazards include other factors such as burning rate or flame spread, intensity of burning, fuel contribution, products of combustion, and others. 1.1 This fire test response test method2 covers a laboratory determination of the flash ignition temperature and spontaneous ignition temperature of plastics using a hot-air furnace. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 Caution—During the course of combustion, gases or vapors, or both, are evolved that have the potential to be hazardous to personnel. 1.4 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 1.3 and 1.4. Note 1: This test method and ISO 871-1996 are identical in all technical details.

Standard Test Method for Determining Ignition Temperature of Plastics

KS M ISO 10840:2013 塑料.标准燃烧试验的使用指南

이 표준은 플라스틱 재료와 제품의 화재 시험에 있어 다음과 같은 사항들에 대하여 적용한다.― 실제 현장 사용 조건을 반영하는 적절한 시험의 선정― 지정된 시험(들)을 측정할 수 있는 화재 반응 특성의 그룹화― 재료 특성, 품질 관리, 사전 예비 시험, 최종 제품 시험, 환경 실태 평가, DfE(친환경 설계)와 같은영역에서 관련이 있는 시험의 평가― 플라스틱을 표준 화재 시험에서 시험할 때 발생할 수 있는 가능한 문제의 정의이 표준의 적용범위는 플라스틱용 새로운 화재 시험의 개발이나 설계를 포함하지 않는다. 그러나 시험편 장착 및 고정과 관련된 접근 유연성은 화재 시험 실험실과 인증 기관에서 다양한 방식으로 사용하는 다양한 플라스틱의 평가 방법을 고려할 때 귀중할 수 있다.

Plastics — Guidance for the use of standard fire tests

ISO 30021:2013 塑料. 燃烧性能. 纤维增强聚合物复合材料的中间尺度耐火测试

This International Standard specifies a method of determining the fire resistance of non-load-bearing separating elements made of fibre reinforced plastics (FRP) when exposed to heating on one face. It is applicable to FRP products for which the end-use application is smaller than the full-scale fire test specimen specified in ISO 834-1. Fire barriers in transportation applications are a common example,since the end-use dimensions of the barrier products are often smaller than those specified in ISO 834-1.

Plastics.Burning behaviour.Intermediate-scale fire-resistance testing of fibre-reinforced polymer composites