49.025.99;75.100 标准查询与下载

SAE ARP5088B-2014 用自动电位滴定测定聚酯和二酯燃气涡轮润滑剂中总酸值的试验方法

The test method describes the procedure for determination of the total acid number of new and degraded polyol ester and diester based gas turbine lubricants by potentiometric titration technique. The method was validated to cover an acidity range 0.05 to 6.0 mg KOH g-1. The method may also be suitable for the determination of acidities outside of this range and for other classes of lubricant.

Test Method for the Determination of Total Acidity in Polyol Ester and Diester Gas Turbine Lubricants by Automatic Potentiometric Titration

SAE ARP5921-2014 使用气相焦炭对空气油雾环境中航空润滑油结焦倾向的评估

This method is designed to evaluate the coking propensity of synthetic ester-based aviation lubricants under two phase air-oil mist conditions as found in certain parts of a gas turbine engine, for instance, bearing chamber vent lines. Based on the results from round robin data in 2008-2009 from four laboratories, this method is currently intended to provide a comparison between lubricants as a research tool; it is not currently a satisfactory pass/fail test. At this juncture a reference oil may improve reproducibility (precision between laboratories); a formal precision statement will be given when there is satisfactory data and an agreed on, suitable refe

Evaluation of Coking Propensity of Aviation Lubricants in an Air-Oil Mist Environment using the Vapor Phase Coker

SAE AS5780B-2013 航空和航空派生的燃气涡轮发动机润滑油规格

This specification defines basic physical, chemical, and performance limits for 5 cSt grades of gas turbine engine lubricating oils used in aero and aero-derived marine and industrial applications, along with standard test methods and requirements for laboratories performing them. It also defines the quality control requirements to assure batch conformance and materials traceability, and the procedures to manage and communicate changes in oil formulation and brand. This specification invokes the Performance Review Institute (PRI) product qualification process. Requests for submittal information may be made to the PRI at the address in Appendix C, referencin

Specification for Aero and Aero-Derived Gas Turbine Engine Lubricants

SAE AMS3053A-2012 抗水烯烃基润滑油

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a water resistant lubricant in the form of grease procured in inch/pound units. MAM 3053 is the metric version of this AMS. This grease has been used typically for lubrication of high speed main shaft bearings of missiles and turbine engines, but usage is not limited to such applications.

Grease, Water Resistant Polyalphaolefin Base

SAE AMS3057A-2012 飞机减速箱用半流体润滑剂

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers semi-fluid lubricant suitable for use in aircraft gearboxes and transmissions. This product has been used typically for lubricating transmissions in wing slat/flap actuators in certain aircraft, and other mechanisms, but usage is not limited to such applications.

Lubricant, Semi-Fluid, for Aircraft Gearboxes

SAE AMS3052-2007 稠化锂低温范围通用航空器润滑剂

This specification covers grease for use within an aircraft. This product is used typically as a lubricant in contact with anti-friction bearings, plain bearings and other mechanisms, but usage is not limited to such applications. Each application should be considered separately. This material has a service temperature range of -100 to +250 °F (-73 to +121 °C) where performance in the presence of water is also required.

Grease, Aircraft, General Purpose, Low Temperature Range, Lithium Thickened

SAE AS5780A-2005 航空和航空衍生的气体涡轮机润滑剂的规范

This specification defines basic physical, chemical, and performance limits for 5 cSt grades of gas turbine engine lubricating oils used in aero and aero-derived marine and industrial applications, along with standard test methods and requirements for laboratories performing them. It also defines the quality control requirements to assure batch conformance and materials traceability, and the procedures to manage and communicate changes in oil formulation and brand. This specification invokes the Performance Review Institute (PRI) product qualification process. Requests for submittal information may be made to the PRI at the address in Appendix C, referencing this specification. Products qualified to this specification are listed on a Qualified Products List (QPL) managed by the PRI. Additional tests and evaluations may be required by individual equipment builders before an oil is approved for use in their equipment. Approval and/or certification for use of a specific gas turbine oil in aero and aero-derived marine and industrial applications is the responsibility of the individual equipment builders and/or governmental authorities and is not implied by compliance with or qualification to this specification.

(R) Specification for Aero and Aero-Derived Gas Turbine Engine Lubricants

SAE AMS3054B-2001 应用于低温零下55度(零下67°F)的润滑油

1.1 Form:This specification covers a petroleum-base lubricating oil.1.2 Application:This lubricant has been used typically for general purpose, low-temperature lubrication applicationswhere low evaporation and rust-preventive characteristics are desired, but usage is not limited to such applications.1.3 Safety - Hazardous Materials:While the materials, methods, applications, and processes described or referenced in thisspecification may involve the use of hazardous materials, this specification does not address thehazards which may be involved in such use. It is the sole responsibility of the user to ensurefamiliarity with the safe and proper use of any hazardous materials and to take necessaryprecautionary measures to ensure the health and safety of all personnel involved.

Oil, Lubricating, Low Temperature for -55 Degrees C (-67 Degrees F) Service

SAE ARP5088A-2000 用自动电位滴定测定聚酯和二酯燃气涡轮润滑剂中总酸值的试验方法

The test method describes the procedure for determination of the total acid number of new and degraded polyol ester and diester based gas turbine lubricants by potentiometric titration technique. The method was validated to cover an acidity range 0.05 to 6.0 mg KOH g\u-. The method may also be suitable for the determination of acidities outside of this range and for other classes of lubricant.

Test Method for the Determination of Total Acidity in Polyol Ester and Diester Gas Turbine Lubricants by Automatic Potentiometric Titration

SAE AMS3057-2000 飞机减速箱用半流体润滑剂

This specification covers semi-fluid lubricant suitable for use in aircraft gearboxes and transmissions. This product has been used typically for lubricating transmissions in wing slat/flap actuators in certain aircraft, and other mechanisms, but usage is not limited to such applications.

Lubricant, Semi-Fluid, for Aircraft Gearboxes

SAE AMS3053-1994 防水合成烃基润滑脂

This specification covers a water resistant lubricant in the form of grease procured in inch/pound units. MAM 3053 is the metric version of this AMS. This grease has been used typically for lubrication of high speed main shaft bearings of missiles and turbine engines, but usage is not limited to such applications.

Grease, Water Resistant Polyalphaolefin Base