共找到 99 条与 相关的标准,共 7 页
This document specifies the requirements for flat products for pressure equipment, made of thermomechanically rolled weldable fine grain steels as specified in Tables A.1 and B.1. The steels are not suitable for hot forming. Until now, no sufficient data for the standardization of the elevated temperature properties of these steels are available. If their use at such temperatures is intended, the conditions for this are specially agreed upon between the interested parties. The requirements and definitions of ISO 9328-1 also apply to this document. NOTE 1 Fine grain steels are understood to be steels with a ferritic grain size of 6 or finer when tested in accordance with ISO 643. NOTE 2 This document offers the possibility of specifying products in accordance with European design codes and ASME-type design codes.
Steel flat products for pressure purposes - Technical delivery conditions - Part 5: Weldable fine grain steels, thermomechanically rolled
This document specifies the requirements for flat products for pressure equipment made of quenched and tempered weldable fine grain steels as specified in Tables A.1 and B.1. The requirements and definitions of ISO 9328-1 also apply to this document. NOTE 1 Fine grain steels are understood to be steels with a ferritic grain size of 6 or finer when tested in accordance with ISO 643. NOTE 2 This document offers the possibility of specifying products in accordance with European design codes and ASME-type design codes.
Steel flat products for pressure purposes - Technical delivery conditions - Part 6: Weldable fine grain steels, quenched and tempered
This document specifies the technical delivery conditions for plates and strip for pressure equipment made of non-alloy and alloy steels as specified in Tables A.1 and B.1. The requirements and definitions
Steel flat products for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
This document specifies requirements for flat products for pressure purposes made of stainless steels, including austenitic creep-resisting steels, in thicknesses as specified in Tables 7 to 10. The requirements and definitions of ISO 9328-1 also apply to this document.
Steel flat products for pressure purposes - Technical delivery conditions - Part 7: Stainless steels
This document specifies the general technical delivery conditions for steel flat products (plate/sheet and strip) used principally for the construction of pressure equipment. The general technical delivery requirements of ISO 404 also apply to products supplied in accordance with this document.
Steel flat products for pressure purposes - Technical delivery conditions - Part 1: General requirements
This document specifies the requirements for flat products for pressure equipment made of weldable fine grain steels as specified in Tables A.1 and B.1. The requirements and definitions of ISO 9328-1 also apply to this document. NOTE 1 Fine grain steels are understood as steels with a ferritic grain size of 6 or finer when tested in accordance with ISO 643. NOTE 2 This document offers the possibility to specifying products in accordance with European design codes and ASME-type design codes.
Steel flat products for pressure purposes - Technical delivery conditions - Part 3: Weldable fine grain steels, normalized
This document specifies the technical delivery conditions for plates and strip for pressure equipment made of nickel-alloy steels as specified in Tables A.1 and B.1. The requirements and definitions of ISO 9328-1 also apply to this document. NOTE This document offers the possibility of specifying products in accordance with European design codes and ASME-type design codes.
Steel flat products for pressure purposes - Technical delivery conditions - Part 4: Nickel-alloy steels with specified low temperature properties
High strength steel plates for pressure vessels for intermediate and moderate temperature service
Flat products made of steels for pressure purposes. Weldable fine grain steels, normalized
Steel sheet and strip for welded gas cylinders
Carbon steel plates for pressure vessels for intermediate and moderate temperature services
Flat products made of steels for pressure purposes - Part 7: Stainless steels; German version EN 10028-7:2016
This European Standard specifies requirements for flat products for pressure purposes made of stainless steels, including austenitic creep resisting steels, in thicknesses as indicated in Tables 7 to 10. The requirements of EN 10028-1 also apply. NOTE 1 The steel grades covered by this European Standard have been selected from EN 10088-1. NOTE 2 Once this European Standard is published in the Official Journal of the European Union (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and Part 7) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done.
Flat products made of steels for pressure purposes - Part 7: Stainless steels
Steel plates for pressure vessels for intermediate temperature service
Carbon steel plates for pressure vessels for low temperature service
High strength steel plates for pressure vessel for intermediate and moderate temperature service
This Japanese Industrial Standard specifies the hot-rolled steel sheets, plates and strips (hereafter referred to as "steel sheets, plates and strips") to be used for welded gas cylinders with a maximum capacity of 500 L which contain such high-pressure gases as LP gas and acetylene.
Steel sheet, plates and strip for gas cylinders
This Standard specifies the hot-rolled nickel steel plates (hereafter referred to as "steel plates") to be used for pressure vessels and storage equipment for low temperature service.
Nickel steel plates for pressure vessels for low temperature services
This part of ISO 9328 specifies the requirements for flat products for pressure equipment, made of thermomechanically rolled weldable fine grain steels as specified in Tables A.1 and B.1. The steels are not suitable for hot forming. Until now, no sufficient data for the standardization of the elevated temperature properties of these steels are available. If their use at such temperatures is intended, the conditions for this are specially agreed upon between the interested parties. The requirements and definitions of ISO 9328-1 also apply to this part of ISO 9328. NOTE 1 Fine grain steels are understood to be steels with a ferritic grain size of 6 or finer when tested in accordance with ISO 643. NOTE 2 This part of ISO 9328 offers the possibility of specifying products in accordance with European design codes and ASME-type design codes.
Steel flat products for pressure purposes - Technical delivery conditions - Part 5: Weldable fine grain steels, thermomechanically rolled
This part of ISO 9328 specifies the requirements for flat products for pressure equipment made of weldable fine grain steels as specified in Tables A.1 and B.1. The requirements and definitions of ISO 9328-1 also apply to this part of ISO 9328. NOTE 1 Fine grain steels are understood as steels with a ferritic grain size of 6 or finer when tested in accordance with ISO 643. NOTE 2 This part of ISO 9328 offers the possibility to specifying products in accordance with European design codes and ASME-type design codes.
Steel flat products for pressure purposes - Technical delivery conditions - Part 3: Weldable fine grain steels, normalized
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号