13.040.99 有关空气质量的其他标准 标准查询与下载

VDI 3476 Blatt 2-2010 废气净化 催化废气净化方法 氧化过程

The guideline VDI 3476 Blatt 1 describes the fundamental principles for method selection, the design, the operating of facilities and the use of catalysts for catalytic waste gas cleaning. This guideline discusses the oxidative methods of waste gas cleaning. The focus is on design documentation and on examples for the practical use of these methods.

Waste gas cleaning - Catalytic waste gas cleaning methods - Oxidative processes

ASTM D4532-10 使用气旋采样器对工作场所环境中的可吸入尘埃进行采样的标准试验方法

This test method covers the determination of respirable dust concentration in workplace atmospheres. Variations of the test method are in world-wide use for determining compliance relative to occupational exposure levels. The test method may be used to verify dust control measures. The test method may also be applied in research into health effects of dust in an occupational setting.1.1 This test method provides details for the determination of respirable dust concentration defined in terms of international convention in a range from 0.5 to 10 mg/m3 in workplace atmospheres. Specifics are given for sampling and analysis using any one of a number of commercially available cyclone samplers. 1.2 The limitations on the test method are a minimum weight of 0.1 mg of dust on the filter, and a maximum loading of 0.3 mg/m2 on the filter. The test method may be used at higher loadings if the flow rate can be maintained constant. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This test method contains notes that are explanatory and are not part of the mandatory requirements of the method. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Respirable Dust in Workplace Atmospheres Using Cyclone Samplers

ASTM D6345-10 空气中挥发性有机化合物的主动、一体化取样方法的选择的标准指南

This guide provides a broad perspective on techniques that can be used by environmental managers for selecting VOC air monitoring methods. It summarizes various methods for measurement of VOC in air derived from a variety of sources and experiences and incorporates them into condensed guidelines. This guide provides a common basis for selecting methods for VOC measurement as well a discussion of the limitations of typical methods. This guide should be used during the planning stages of an air monitoring program along with other applicable guides and practices (for example, D1357) to select ASTM or other appropriate methods.1.1 This guide provides assistance in the selection of active integrative sampling methods, in which the volatile organic analytes are collected from air over a period of time by drawing the air into the sampling device, with subsequent recovery for analysis. Where available, specific ASTM test methods and practices are referenced. 1.2 Guidance is provided for the selection of active sampling methods based either on collection of an untreated air sample (whole air samples) or selective sampling using sorbent concentration techniques that selectively concentrate components in air. Advantages and disadvantages of specific collection vehicles are presented. 1.3 This guide does not cover the use of cryogenically cooled field sampling devices used in some automated analysis systems. Detailed instructions for cryogenic recovery of compounds captured as whole air samples or thermally desorbed from sorbents are typically covered in standard methods for sample analysis and are beyond the scope of this guide. 1.4 Both thermal and solvent desorption techniques for sample recovery are discussed. 1.5 Organic compounds are classified on the basis of vapor pressure as very volatile, volatile, semivolatile and nonvolatile. Physical characteristics of many volatile organic compounds (VOCs) are provided to aid in selection of sampling techniques for VOC measurement. Semivolatile and nonvolatile organic compounds are defined in the guide to help guide users avoid misidentifying compounds that are not covered in this guide. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Selection of Methods for Active, Integrative Sampling of Volatile Organic Compounds in Air

DIN EN 15267-2:2009 空气质量.自动测量系统的认证.第2部分:AMS制造商质量制造过程的管理体系和认证后监管的初步评估.英文版本DIN EN 15267-2-2009-07

This European Standard specifies the requirements for the manufacturer's quality management system, the initial assessment of the manufacturer's production control and the continuing surveillance of the effect of subsequent design changes on the performance of certified automated measuring systems. This European Standard also serves as a reference document for auditing the manufacturer's quality management system.

Air quality - Certification of automated measuring systems - Part 2: Initial assessment of the AMS manufacturers quality management system and post certification surveillance for the manufacturing process; English version of DIN EN 15267-2:2009-07

DIN EN 15267-1:2009 空气质量.自动测量系统的质量保证.第1部分:一般原则.英文版本DIN EN 15267-1-2009-07

This European Standard specifies the general principles, including common procedures and requirements, for the product certification of automated measuring systems (AMS) for monitoring ambient air quality and emissions from stationary sources. This product certification consists of the following sequential stages: a) performance testing of an automated measuring system; b) initial assessment of the AMS manufacturer's quality management system; c) certification; d) surveillance. This European Standard applies to the certification of all AMS for monitoring ambient air quality and emissions from stationary sources for which performance criteria and test procedures are available in European Standards.

Air quality - Certification of automated measuring systems - Part 1: General principles; English version of DIN EN 15267-1:2009-07

LST EN 15267-2-2009 空气质量 自动测量系统的认证 第2部分：AMS 制造商质量管理体系的初步评估和制造过程的认证后监督

Air quality - Certification of automated measuring systems - Part 2: Initial assessment of the AMS manufacturer?s quality management system and post certification surveillance for the manufacturing process

LST EN 15267-1-2009 空气质量 自动测量系统的认证 第1部分：一般原则

Air quality - Certification of automated measuring systems - Part 1: General principles

BS EN 15267-1:2009 空气质量.自动化测量系统的证书.通用原理

This European Standard specifies the general principles, including common procedures and requirements, for the product certification of automated measuring systems (AMS) for monitoring ambient air quality and emissions from stationary sources. This product certification consists of the following sequential stages: a) performance testing of an automated measuring system; b) initial assessment of the AMS manufacturer’s quality management system; c) certification; d) surveillance. This European Standard applies to the certification of all AMS for monitoring ambient air quality and emissions from stationary sources for which performance criteria and test procedures are available in European Standards.

Air quality - Certification of automated measuring systems - Part 1: General principles

BS EN 15267-2:2009 空气质量.自动测量系统的认证.第2部分:AMS制造商的质量管理系统的初始评估和制造工艺的认证后监督

This European Standard specifies the requirements for the manufacturer’s quality management system, the initial assessment of the manufacturer’s production control and the continuing surveillance of the effect of subsequent design changes on the performance of certified automated measuring systems. This European Standard also serves as a reference document for auditing the manufacturer’s quality management system.

Air quality - Certification of automated measuring systems - Part 2: Initial assessment of the AMS manufacturer's quality management system and post certification surveillance for the manufacturing process

SNI 7248-2009 工作场所空气中铅(Pb)含量静态测试测量

Static test measurement of lead (Pb) content in the air in the workplace

SNI 7249-2009 工作场所空气中甲苯含量的静态测试方法

Static test method for toluene content in workplace air

ASTM D6178-97(2008) 估计短期吸入暴露于寝具组发出的挥发性有机化学品的标准做法

Standard Practice for Estimation of Short-term Inhalation Exposure to Volatile Organic Chemicals Emitted from Bedding Sets

DIN EN 15267-3:2008 空气质量.自动测量系统的质量保证.第3部分:固定源排放监控用自动测量系统的性能标准和试验程序

This European Standard specifies the performance criteria and test procedures for automated measuring systems that measure gases and particulate matter in, and flow of, the waste gas from stationary sources. This European Standard supports the requirements of particular EU Directives. It provides the detailed procedures covering the QAL1 requirements of EN 14181 and, where required, input data used in QAL3.

Air quality - Certification of automated measuring systems - Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources; English version of DIN EN 15267-3:2008-03

CNS 15047-2008 香品

Joss sticks

CNS 15095-2007 金、银纸

本标准适用于信仰焚烧用之金、银纸（以下简称为金银纸），惟纸祭品除外。

Joss Papers

CNS 15047-2006 香品

本标准适用于宗教仪式燃烧用之香品（俗称拜香incense）。惟不包括熏香

Joss sticks

VDI 2066 Blatt 1-2006 颗粒物测量 流动气体中的粉尘测量 粉尘负荷的重量法测定

Guideline VDI 2066 Part 1 specifies a manual gravimetric reference measurement method for the determination of the dust load (dust content) and the dust mass flow of a dust/gas mixture flowing through a defined cross-section (e.g. stacks, pipelines or ducts). Such measurement tasks mainly arise, if dust emissions have to be determined e.g. in case of a check of compliance with limit or guarantee values, calibration of automated dust emission measuring systems, performance measurements at dust precipitators, and during check or optimization of process parameters. This guideline can be applied at different dust contents according to the following application ranges, and in case of wet or water-vapour saturated flue gas as well as in case of over-saturated flue gas with water droplets. It is applicable in the following application ranges: Application Range A: cleaned-up gas with concentrations up to 50 mg/m3, Application Range B: cleaned-up gas with concentrations up to 150 mg/m3, Application Range C: intermediate gas with concentrations up to 2 g/m3, Application Range D: raw gas with concentrations e.g. up to 100 g/m3 The sampling time of a single measurement is usually 30 min. Guideline VDI 2066 Part 1 is applicable to measurements at stationary sources. For the Application Range A, the technical requirements of this guideline are identical to those of DIN EN 13284-1. In this case, they fulfil the normative requirements of DIN EN 13284-1. For plants covered by European Directives [G5; G6], the dust measurement according to DIN EN 13284-1 is strictly required. This applies to plants the erection and operation of which is regulated by the 13th or 17th Ordinance [G2; G3] on the implementation of the German Federal Immission Control Act [G1]. If the dust measurement is carried out for these plants in accordance with Application Range A of this guideline, the equivalence with DIN EN 13284-1 shall be indicated in the measurement report. This guideline also provides procedures for special operating conditions and interfering components in the flue gas.

Particulate matter measurement - Dust measurement in flowing gases - Gravimetric determination of dust load

DIN EN ISO 16000-11:2006 室内空气.第11部分:建筑产品和家具释放挥发性有机化合物的测定.取样、样品储藏和试验样品制备

Studies of emission of volatile organic compounds (VOCs) from building products or furnishing in test chambers or cells require proper handling of the product prior to testing and during the testing period. The present standard specifies sampling, storage of samples, the transport conditions and the preparation of test specimens.

Indoor air - Part 11: Determination of the emission of volatile organic compounds from building products and furnishing - Sampling, storage of samples and preparation of test specimens (ISO 16000-11:2006); English version of DIN EN ISO 16000-11:2006-06

DIN EN ISO 16000-10:2006 室内空气.第9部分:建筑产品和家具释放挥发性有机化合物的测定.释放试验容器法

The project specifies a general laboratory test method for determination of area specific emission rate of volatile organic compounds (VOCs) from newly produced building products or furnishing under defined climate conditions. This method can also, in principle, be applied to aged products. The emission data obtained can be used to calculate concentrations in a model room. Part 10 is applicable for different types of emission test cells used for the determination of volatile organic compounds from building products or furnishing. According to the use of an emission test cell, it is also possible to perform non-destructive emission measurements on building products or furnishing on-site in buildings. However, the procedure for such measurements is not described in this standard (see DIN ISO 16000-6).

Indoor air - Part 10: Determination of the emission of volatile organic compounds from building products and furnishing - Emission test cell method (ISO 16000-10:2006); English version of DIN EN ISO 16000-10:2006-06

LST EN 13725-2004/AC-2006 空气质量 动态嗅觉法测定气味浓度

Air quality - Determination of odour concentration by dynamic olfactometry