13.040.99 有关空气质量的其他标准 标准查询与下载

ASTM E2913/E2913M-21 从复合擦拭样品中加热消解铅的标准实施规程

1.1 This practice is similar to Practice E1644 and covers the hot, nitric acid digestion of lead (Pb) from a composited sample of up to four individual wipe samples of settled dust collected from equally-sized areas in the same space. 1.2 This practice contains notes which are explanatory and not part of mandatory requirements of the practice. 1.3 This practice should be used by analysts experienced in digestion techniques such as hot blocks. Like all procedures used in an analytical laboratory, this practice needs to be validated for use and shown to produce acceptable results before being applied to client samples. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Hotplate Digestion of Lead from Composited Wipe Samples

ASTM E2914/E2914M-21 从复合擦拭样品中超声提取铅的标准实施规程

1.1 This practice covers the extraction of lead (Pb) using ultrasonication, heat and nitric acid from a composited sample of up to four individual wipe samples of settled dust collected from equally-sized areas in the same space. 1.2 This practice contains notes which are explanatory and not part of mandatory requirements of the practice. 1.3 This practice should be used by analysts experienced in digestion techniques such as hot blocks. Like all procedures used in an analytical laboratory, this practice needs to be validated for use and shown to produce acceptable results before being applied to client samples. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Ultrasonic Extraction of Lead from Composited Wipe Samples

ASTM D6552-06(2021) 控制和表征收集的气溶胶称重误差的标准实施规程

1.1 Assessment of airborne aerosol hazards in the occupational setting entails sampling onto a collection medium followed by analysis of the collected material. The result is generally an estimated concentration of a possibly hazardous material in the air. The uncertainty in such estimates depends on several factors, one of which relates to the specific type of analysis employed. The most commonly applied method for analysis of aerosols is the weighing of the sampled material. Gravimetric analysis, though apparently simple, is subject to errors from instability in the mass of the sampling medium and other elements that must be weighed. An example is provided by aerosol samplers designed to collect particles so as to agree with the inhalable aerosol sampling convention (see ISO 7708, Guide D6062, and EN 481). For some sampler types, filter and cassette are weighed together to make estimates. Therefore, if the cassette, for example, absorbs or loses water between the weighings required for a concentration estimation, then errors may arise. This practice covers such potential errors and provides solutions for their minimization. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Controlling and Characterizing Errors in Weighing Collected Aerosols

FprEN 13725-2021 固定源排放 用动态嗅觉法和气味排放率测定气味浓度

Stationary source emissions - Determination of odour concentration by dynamic olfactometry and odour emission rate

T/IMAS 029-2021 木材干燥尾气挥发性有机物（VOCs）取样和检测方法

1  范围　 2  规范性引用文件　 3  术语和定义　 4  方法原理　 5  试剂和材料　 6  仪器和设备　 7  挥发性有机物采样方法　 8  分析步骤　 9  结果计算　 10  质量保证与质量控制　 11  测试报告　

Method for sampling and determination of volatile organic compounds(VOCs) from wood drying processing

GSO ASTM D6330:2021 在规定的测试条件下使用小型环境室测定人造板挥发性有机化合物（不包括甲醛）排放的标准实施规程

1.1 The practice measures the volatile organic compounds (VOC), excluding formaldehyde, emitted from manufactured wood-based panels. A pre-screening analysis is used to identify the VOCs emitted from the panel. Emission factors (that is, emission rates per unit surface area) for the VOCs of interest are then determined by measuring the concentrations in a small environmental test chamber containing a specimen. The test chamber is ventilated at a constant air change rate under the standard environmental conditions. For formaldehyde determination, see Test Method D6007. 1.2 This practice describes a test method that is specific to the measurement of VOC emissions from newly manufactured individual wood-based panels, such as particleboard, plywood, and oriented strand board (OSB), for the purpose of comparing the emission characteristics of different products under the standard test condition. For general guidance on conducting small environmental chamber tests, see Guide D5116. 1.3 VOC concentrations in the environmental test chamber are determined by adsorption on an appropriate single adsorbent tube or multi-adsorbent tube, followed by thermal desorption and combined gas chromatograph/mass spectrometry (GC/ MS) or gas chromatograph/flame ionization detection (GC/ FID). The air sampling procedure and the analytical method recommended in this practice are generally valid for the identification and quantification of VOCs with saturation vapor pressure between 500 and 0.01 kPa at 25°C, depending on the selection of adsorbent(s).

Standard Practice for Determination of Volatile Organic Compounds (Excluding Formaldehyde) Emissions from Wood-Based Panels Using Small Environmental Chambers Under Defined Test Conditions

DB45/T 2318-2021 环境空气质量自动监测站建设技术规范

Technical specifications for the construction of automatic monitoring stations for ambient air quality

T/GIEHA 027-2021 雄安新区绿色室内空气净化产品及服务入选指南

产品要求见表1。 表1 产品要求 序号　产品类型　产品要求 1　空气净化设备 （空气净化器、新风系统）　a）空气净化设备需通过“第三方”认证机构认证，产品性能应达到T/CAQI 17、T/CAQI 33、T/CAQI 34、T/CAQI 35、T/GIEHA 008、T/GIEHA 010、T/GIEHA 021等分级标准中“九颗星”的要求； b）年度空气净化产品的品牌评价应达到T/CCBD 8-2020中“一线品牌”的要求。 2　照明　a）照明需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）照明的品牌应达到品牌评价中“一线品牌”的要求。 3　电梯　a）电梯需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）电梯的品牌应达到品牌评价中“一线品牌”的要求。 4　负离子装置　a）负离子装置需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）负离子装置的品牌应达到品牌评价中“一线品牌”的要求。 5　厨具　a）厨具需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）厨具的品牌应达到品牌评价中“一线品牌”的要求。 6　消毒设备　a）消毒设备需通过“第三方”认证机构认证，产品性能达到 T/GIEHA 021分级标准中“九颗星”的要求； b）消毒设备需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； c）消毒设备的品牌应达到品牌评价中“一线品牌”的要求。 7　家具　a）家具各项指标应符合GB/T 35607、GB 28481的相关要求； b）家具需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； c）健康家具的品牌应达到品牌评价中“一线品牌”的要求。 8　门窗　a）门窗需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）门窗的品牌应达到品牌评价中“一线品牌”的要求。 9　空调　a）空调产品需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）空调的品牌评价应达到T/GIEHA 022中“一线品牌”的要求。 10　建材（涂料、陶瓷等）　a)建材各项指标应符合GB18580、GB 18581、GB18582、GB18583、GB18584、GB18585、GB18586、GB18587的相关要求； b)建材需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； c）建材的品牌应达到品牌评价中“一线品牌”的要求。 11　空气净化设备配件 （风机、滤网、传感器等）　a）需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）品牌应达到品牌评价中“一线品牌”的要求。 3.3.2　服务及相关产品要求 服务及相关产品要求见表2。 表2服务及相关产品要求 1　室内环境污染治理及产品 　a）室内环境污染治理产品需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）室内环境污染治理的产品品牌应达到品牌评价中“一线品牌”的要求； c）符合T/GIEHA 002规定的要求，并且获得由相关行业协会颁发对应的甲级资质。 2　集中空调通风系统清洗消毒及产品　a）集中空调通风系统清洗消毒产品需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）集中空调通风系统清洗消毒的产品品牌应达到品牌评价中“一线品牌”的要求； c）符合T/GIEHA 003规定的要求，并且获得由相关行业协会颁发对应的甲级资质。 3　油烟管道清洗服务及产品　a）油烟管道清洗服务及产品需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； b）油烟管道清洗服务及产品品牌应达到品牌评价中“一线品牌”的要求； c）符合T/GIEHA 014规定的要求，并且获得由相关行业协会颁发对应的甲级资质。 4　室内空气质量检（监）测系统产品　a）室内空气质量实时检（监）测可视化产品各项指标应符合T/CAQI 39、T/GIEHA 024的相关要求； b）室内空气质量实时检（监）测可视化产品需经第三方检测机构检测，《检测报告》显示各项技术指标应达到行业同类产品前列； c）室内空气质量实时检（监）测可视化产品的品牌应达到品牌评价中“一线品牌”的要求。

Selection Guide For Green Indoor Air Purification Products, Materials And Services In Xiong'an New District

T/GIEHA 026-2021 雄安新区室内空气质量分级

表1  室内空气质量标准分级 序号　项目　平均时间　分级指标　单位 　　　一级　二级　三级　 1　新风量　　30　m3/(h*人) 2　二氧化硫SO2　1小时平均值　0.20　0.35　0.50　mg/m3 3　二氧化氮NO2　1小时平均值　0.2　0.22　0.24　mg/m3 4　一氧化碳CO　1小时平均值　10　mg/m3 5　二氧化碳CO2　日平均值　0.07　0.09　0.10　% 6　氨NH3　1小时平均值　0.15　mg/m3 7　臭氧O3　1小时平均值　0.1　0.13　0.16　mg/m3 8　甲醛HCHO　1小时平均值　0.03　0.05　0.07　mg/m3 9　苯C6H6　1小时平均值　0.017　0.039　0.06　mg/m3 10　甲苯C7H8　1小时平均值　0.15　mg/m3 11　二甲苯C8H10　1小时平均值　0.20　mg/m3 12　苯并[a]芘B(a)P　日平均值　1.0　ng/m3 13　可吸入颗粒物 PM10　日平均值　0.05　0.10　0.15　mg/m3 14　可吸入颗粒物PM2.5　日平均值　25　50　75　ug/m3 15　总挥发性有机物TVOC　8小时均值　0.20　0.33　0.45　mg/m3 16　负离子　1小时均值　1500　个/cm3 17　菌落总数　依据仪器定　500　1000　1500　cfu/m3 18　氡222Rn　年平均值 （行动水平c）　100　125　150　Bq/m3 注：以上分级指标说明见附录A。 新风量和负离子≧分级指标，其他参数要求≦分级指标。

Classification of indoor air quality in Xiong'an New district

T/ZAAM 0001-2021 乘用车内饰零部件及材料气味评价方法——稀释法

本标准包括一套完整的稀释法气味评价方法和相关设备、人员的要求。同时包括了方法限值制定的一般过程，适用于将现有的气味评价标准与本方法进行良好的转化。方法包括了对实验环境的要求、对实验设备的要求及对从事气味评价人员的要求，包括使用到的设备气体采集装置和气体评价装置。实验过程按样品下线要求、样品包装要求、样品的取样要求、样品的预处理、样品气袋的清洗、样品的气味培养、样品的气体采集与稀释、样品的评价和对评价数据的处理等各个过程。其中针对本方法的限值制定提出了一套基与气体强度和浓度关系的算法，本方法创新性的提出了将多个等级的主观评价替换为判断气味有无的选择性评价方法，简化了气味评价的表述，大大降低了气味评价人员主观选择难度，降低了评价的主观性，提高了数据的一致性、准确性与科学性；优化了传统的瓶子气味评价方法，使材料、零部件、整车气味评价能采用相同的评价方法；降低了气味评价的实验误差提高数据的有效性与可靠性；提高了不同层级产品之间的数据传递性，有利于整车、零部件、材料的气味整改、溯源与管控。该方法能与现有方法实现良好的过渡，为国家标准、行业标准的制定提供了重要的参考价值。该方法的提出能更好的应用于汽车零部件产品的气味一致性管控，有利于汽车气味品质的改善与提升。

Odor evaluation method for interior parts and materials of passenger cars--dilution method

T/CAQI 198-2021 分户新风净化系统

一般规定、新风净化系统设置、新风净化机选型设计、室外风口及室内气流组织设计、风管系统设计、监测与控制。

Household fresh air purification system

T/CAQI 203-2021 建筑通风系统用空气净化消毒装置

外观与试运转、性能要求、电气安全。

Air purification and disinfection device for building ventilation system

T/CAQI 202-2021 空气离子测量仪

启动与运转、输入功率、离子迁移率、离子浓度准确度测试、重复性试验、电气安全。

Air ion detector

DB33/T 310003-2021 长三角生态绿色一体化发展示范区固定污染源废气现场监测技术规范

Technical specifications for on-site monitoring of waste gas from fixed pollution sources in the Yangtze River Delta Ecological Green Integrated Development Demonstration Zone

DB32/T 310003-2021 长三角生态绿色一体化发展示范区固定污染源废气现场监测技术规范

本文件适用于长三角生态绿色一体化发展示范区（以下简称“示范区”）内固定污染源有组织排放和无组织排放废气现场监测的行为指南及质量保证与控制，示范区范围覆盖上海市青浦区、江苏省苏州市吴江区和浙江省嘉兴市嘉善县

Technical specifications for on-site monitoring of waste gas from fixed pollution sources in the Yangtze River Delta Ecological Green Integrated Development Demonstration Zone

DB31/T 310003-2021 长三角生态绿色一体化发展示范区固定污染源废气现场监测技术规范

Technical specifications for on-site monitoring of waste gas from fixed pollution sources in the Yangtze River Delta Ecological Green Integrated Development Demonstration Zone

JIS A 1460:2021 建筑板材甲醛释放量测定. 干燥剂法

Determination of the emission of formaldehyde from building boards -- Desiccator method

T/GZBC 45.1-2021 高效稳定餐饮油烟净化系统 第1部分：设计安装及运维管理规范

本文件规定了高效稳定餐饮油烟净化系统相关的术语定义、选址、设计、选型、安装、运行维护管理等要求。 本文件适用于餐饮场所选址，高效稳定餐饮油烟净化系统新建或改造时的系统设计、设备选型安装及日常运维管理。

Highly efficient and stable cooking fume purification systems— Part 1: Code of practice for design, installation and operation management

DB5301/T 50-2021 餐饮业油烟污染排放要求

本标准对餐饮业油烟污染物排放的控制要求、监测要求及监督与管理做出了规定。 本标准适用于对餐饮服务单位油烟污染物排放的规范、管理与监督。本标准不适用于以蒸、煮烹饪 方式为主的餐饮单位。

Requirements for Discharge of Oil Fume Pollution from Catering Industry

T/CAQI 140-2020 便携式甲醛检测仪

测试条件及测试用仪器仪表、外观、启动与运转、检测误差、示值重复性、漂移、干扰与排除。

Portable formaldehyde detector