25.220.10 标准查询与下载

GB/T 18839.3-2002 涂覆涂料前钢材表面处理 表面处理方法 手工和动力工具清理

本标准规定了涂覆涂料前钢材表面处理的方法一一手工和动力工具清理。 本标准适用于新的钢构件，也适用于以前涂覆过涂料但有些区域受损或全部需要重新涂覆涂料的钢材表面。

Preparation of steel substrates before application of paints and related products--Surface preparation methods--Hand-and power-tool cleaning

GB/T 18839.2-2002 涂覆涂料前钢材表面处理 表面处理方法 磨料喷射清理

本标准规定了涂覆涂料前钢材表面处理方法磨料喷射清理的定义及其方法、所用磨料和工艺程序等。 本标准适用于未涂过涂料或已涂有涂料的新的和已腐蚀的钢材表面的清理。

Preparation of steel substrates before application of paints and related products--Surface preparation methods--Abrasive blast-cleaning

GB/T 18838.1-2002 涂覆涂料前钢材表面处理 喷射清理用金属磨料的技术要求 导则和分类

GB／T l8838的本部分规定了涂覆涂料前钢材表面喷射清理用的金属磨料(以下简称金属磨料)的分类和标记等。 本部分适用于未经使用过的金属磨料的标记。 注1：虽然本部分IS0 11124是为满足钢构件处理要求而特别制定的，但规定的这些特性一般也适用于使用喷射清 理技术处理的其他材料的表面和部件。这些技术已在IS0 8504—2：2000((涂覆涂料前钢材表面处理表面处理 方法第2部分：磨料喷射清理》中规定。

Preparation of steel substrates before application of paints and related products--Specifications for metallic blast-cleaning abrasives--General introduction and classification

GB/T 17850.1-2002 涂覆涂料前钢材表面处理 喷射清理用非金属磨料的技术要求导则和分类

GB／T l7850的本部分规定了涂覆涂料前钢材表面处理 喷射清理用的非金属磨料(以下简称非金属磨料)的分类和标记等。 本部分适用于未经使用过的非金属磨料的标记。 注1：虽然本部分IS0 11126是为满足钢构件处理要求而特别制定的，但规定的这些特性一般也适用于使用喷射清 理技术处理的其他材料的表面和部件。这些技术已在ISQ 8504—2：2000《涂覆涂料前钢材表面处理表面处理 方法第2部分：磨料喷射清理》中规定。

Preparation of steel substrates before application of paints and related products--Specifications for non-metallic blast-cleaning abrasives--General introduction and classification

GB/T 6807-2001 钢铁工件涂装前磷化处理技术条件

本标准规定了钢铁工件涂装前的磷化膜分类、技术要求、检验方法及验收规则。 本标准适用于钢铁工件涂装前的磷化处理。经处理所形成的磷化膜用作涂装底层，以增强涂膜与钢铁基体的附着力及耐蚀性，提高钢铁工件的涂装质量。

Specifications for phosphating treatment of iron and steel parts before painting

GB/T 18570.4-2001 涂覆涂料前钢材表面处理 表面清洁度的评定试验 涂覆涂料前凝露可能性的评定导则

本标准给出了涂覆涂料前钢材表面凝露可能性的评定导则。 本标准适用于确定施工现场的环境条件是否适合于涂覆涂料。

Preparation of steel substrates before application of paints and related products--Tests for the assessment of surface cleanliness--Guidance on the estimation of the probability of condensation prior to paint application

GB/T 18570.2-2001 涂覆涂料前钢材表面处理 表面清洁度的评定试验 清理过的表面上氯化物的实验室测定

本标准规定了测定钢材表面水溶性氯化物的方法。 本标准适用于钢材表面的氯化物的测定。本标准也适用于以前涂覆过涂料的表面。本标准不适用于湿喷砂时用铬酸盐或亚硝酸盐作缓蚀剂处理过的钢材表面。

Preparation of steel substrates before application of paints and related products--Tests for the assessment of surface cleanliness--Laboratory determination of chloride on cleaned surfaces

23/30461756 DC BS ISO 8504-5 在涂覆油漆和相关产品之前准备钢基材 表面处理方法 第5部分：水射流（水射流清洗）

BS ISO 8504-5. Preparation of steel substrates before application of paints and related products. Surface preparation methods - Part 5. Water Jetting (Water Jet Cleaning)

ASTM D4579-00(2023) 处理酸性脱脂剂或蒸馏器的标准实施规程

Standard Practice for Handling an Acid Degreaser or Still

BS EN ISO 11127-7:2022 在涂覆油漆和相关产品之前准备钢基材 非金属喷砂清理磨料的测试方法 水溶性氯化物的测定

1   Scope This document specifies the apparatus, the reagents and the procedure to be used in conducting the neutral salt spray (NSS), acetic acid salt spray (AASS) and copper-accelerated acetic acid salt spray (CASS) tests for assessment of the corrosion resistance of metallic materials, with or without permanent or temporary corrosion protection. It also describes the method employed to evaluate the corrosivity of the test cabinet environment. It does not specify the dimensions or types of test specimens , the exposure period to be used for a particular product, or the interpretation of results. Such details are provided in the appropriate product specifications. The salt spray tests are particularly useful for detecting discontinuities, such as pores and other defects, in certain metallic, organic, anodic oxide and conversion coatings. The NSS test is particularly applicable to: — metals and their alloys; — metallic coatings (anodic and cathodic); — conversion coatings; — anodic oxide coatings; — organic coatings on metallic materials. The AASS test is especially useful for testing decorative ...

Preparation of steel substrates before application of paints and related products. Test methods for non-metallic blast-cleaning abrasives. Determination of water-soluble chlorides

BS EN ISO 11127-6:2022 在涂覆油漆和相关产品之前准备钢基材 非金属喷砂清理磨料的测试方法 通过电导率测量测定水溶性污染物

1   ​Scope This document specifies a method for the determination of water-soluble contaminants in non-metallic blast-cleaning abrasives by conductivity measurement. This is one of a number of parts in the ISO 11127 series dealing with the sampling and testing of non-metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements on each are contained in the ISO 11126 series. The ISO 11126 series and the ISO 11127 series have been drafted as a coherent set of International Standards on non-metallic blast-cleaning abrasives.

Preparation of steel substrates before application of paints and related products. Test methods for non-metallic blast-cleaning abrasives. Determination of water-soluble contaminants by conductivity measurement

EN ISO 11127-7:2022 使用涂料及相关产品前钢材的预处理.喷丸处理非金属磨料试验方法.第7部分:水溶性氯化物的测定

This document specifies three methods for the determination of water-soluble chlorides in non-metallic blast-cleaning abrasives, namely, amperometric titration, spectro-photometry and ion chromatography. This document is part of the ISO 11127 series dealing with the sampling and testing of non-metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements on each are contained in the ISO 11126 series. The ISO 11126 series and the ISO 11127 series have been drafted as a coherent set of International Standards on non-metallic blast-cleaning abrasives.

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 7: Determination of water-soluble chlorides (ISO 11127-7:2022)

ISO 11127-7:2022 涂料和相关产品使用前钢衬底的制备.非金属喷砂清理磨料的试验方法.第7部分:水溶性氯化物的测定

Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 7: Determination of water-soluble chlorides

EN ISO 11127-6:2022 涂装油漆和有关产品前钢材预处理喷射清理用非金属磨料的试验方法.第6部分:通过测量电导率测定水溶性杂质

This document specifies a method for the determination of water-soluble contaminants in non-metallic blast-cleaning abrasives by conductivity measurement. This is one of a number of parts in the ISO 11127 series dealing with the sampling and testing of non-metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements on each are contained in the ISO 11126 series. The ISO 11126 series and the ISO 11127 series have been drafted as a coherent set of International Standards on non-metallic blast-cleaning abrasives.

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 6: Determination of water-soluble contaminants by conductivity measurement (ISO 11127-6:2022)

ASTM D7120/D7120M-10(2022) 涂层用屋顶膜的评价和制备标准指南

1.1 This guide covers the procedures for evaluating and preparing non-aggregate surfaced membranes for the application of a coating. It does not address design, construction, or installation issues regarding the roof assembly or the roof membrane. It is not an application guide for roof coatings. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Evaluation and Preparation of Roof Membranes for Coating Application

BS EN ISO 11125-9:2022 在涂覆油漆和相关产品之前准备钢基材 金属喷砂清理磨料的试验方法 磨损试验和性能

Preparation of steel substrates before application of paints and related products. Test methods for metallic blast-cleaning abrasives - Wear testing and performance

ISO 11127-6:2022 涂料和相关产品使用前钢衬底的制备.非金属喷砂清理磨料的试验方法.第6部分:通过电导率测量测定水溶性污染物

This document specifies a method for the determination of water-soluble contaminants in non-metallic blast-cleaning abrasives by conductivity measurement. This is one of a number of parts in the ISO 11127 series dealing with the sampling and testing of non- metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements on each are contained in the ISO 11126 series. Standards on non-metallic blast-cleaning abrasives.

Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 6: Determination of water-soluble contaminants by cond

ASTM B183-18(2022) 电镀用低碳钢的制备

1.1 This practice is intended as an aid to electroplaters in setting up a suitable cleaning cycle preparatory to electroplating of low-carbon steel (Note 1) containing less than 0.35 mass % of carbon and to indicate some of the precautions that must be taken to maintain this cycle in good operating condition. NOTE 1—The preparation of high-carbon steel for electroplating is covered in Guide B242. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Low-Carbon Steel for Electroplating

BS ISO 8504-4:2022 在涂覆油漆和相关产品之前准备钢基材 表面处理方法-酸洗

1   ​Scope This document describes the typical method for acid pickling generally used in a shop facility for the preparation of steel substrates before application of paints and related products. It is in general applicable to new steelwork. This method is essentially intended to remove rust and mill scale. Typically, only slight oil residues can be removed during this process. It can be used on steel surfaces that are easily deformed by abrasive blasting.

Preparation of steel substrates before application of paints and related products. Surface preparation methods - Acid pickling

ISO 8504-4:2022 涂料和相关产品使用前钢衬底的制备.表面制备方法.第4部分:酸洗

Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 4: Acid pickling