25.220.10 标准查询与下载

EN ISO 11125-9:2022 涂料和相关产品使用前钢基体的制备.金属喷砂清理磨料的试验方法.第9部分:磨损试验和性能

This document specifies three procedures to test the service life of a blast-cleaning abrasive under laboratory conditions. The performance of an abrasive is also measured by its ability to clean, via transmission of kinetic energy to the substrate in the blasting process. This document also specifies the procedures that can be performed in the same testing machines to help evaluate abrasive performance under laboratory conditions. This document applies to the testing of virgin metallic blasting media in the delivery state by centrifugal blasting under laboratory conditions.

Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 9: Wear testing and performance (ISO 11125-9:2021)

ASTM B480-88(2022) 电镀用镁和镁合金制备的标准指南

1.1 This guide describes two processes used for plating on magnesium and magnesium alloys: direct electroless nickel plating and zinc immersion. Some users report that the direct electroless nickel procedure does not produce quite as high a level of adhesion as zinc immersion. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 5.1.1 and 5.2.9.2. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Preparation of Magnesium and Magnesium Alloys for Electroplating

ASTM B253-11(2022) 电镀用铝合金制备的标准指南

1.1 This guide covers cleaning and conditioning treatments used before metal deposition (Section 5), and immersion deposit/strike procedures (Section 6) that enhance the adhesion of metals that are subsequently applied to aluminum products by electrodeposition or by autocatalytic chemical reduction. 1.2 The following immersion deposit/strike procedures are covered: 1.2.1 Zinc immersion with optional copper strike (6.3). 1.2.2 Zinc immersion with neutral nickel strike (6.4). 1.2.3 Zinc immersion with acetate-buffered, nickel glycolate strike (6.5). 1.2.4 Zinc immersion with acid or alkaline electroless nickel strike. 1.2.5 Tin immersion with bronze strike (6.6). 1.3 From the processing point of view, these procedures are expected to give deposits on aluminum alloys that are approximately equivalent with respect to adherence. Corrosion performance is affected by many factors, however, including the procedure used to prepare the aluminum alloy for electroplating. 1.4 This guide is intended to aid electroplaters in preparing aluminum and its alloys for electroplating. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements see Section 7 and Appendix X1. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Preparation of Aluminum Alloys for Electroplating

ASTM D5703-95(2022)e1 粘土砖砌体的预处理表面清洁的标准实施规程

1.1 This practice covers non-abrasive surface cleaning of clay brick masonry to remove surface contaminants such as dirt, grease, loose material, soot, fly ash, hydrocarbon residues, algae, etc. in preparation for the application of water repellent coatings without damaging or altering the surface appearance of the clay brick masonry. 1.2 Procedures included in this practice are water cleaning, detergent water cleaning, pressurized water cleaning, steam cleaning, and acid cleaning. It is not intended for the cleaning of newly constructed brick masonry. Use of procedures described in this practice may not be appropriate where the surface is of a historical nature. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard information see Section 5, 6.4.1.1, and 6.4.1.2. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry

ASTM D6386-22 涂漆用锌（热浸镀锌）涂层钢铁产品和五金件表面制备的标准实施规程

1.1 This practice describes methods of preparing surfaces of new and weathered hot-dip galvanized steel for painting with liquid paint and coating products. Preparing surfaces of new and partially weathered galvanized steel for powder coating is addressed in Practice D7803. Hot-dip galvanized steel is produced by the immersion of fabricated or unfabricated products in a bath of molten zinc, as specified in Specifications A123/A123M or A153/A153M. This practice covers surface preparation on iron and steel products and hardware that have not been painted previously. Galvanized surfaces may have been treated with protective coatings to prevent the occurrence of wet storage stain. This practice does not apply to sheet galvanized steel products nor to the coil coating or continuous roller coating processes. Sheet and coil surface preparation can be done in accordance with Practice D7396. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Painting

22/30413960 DC BS ISO 11128 喷砂清理磨料规范 可回收的封装磨料介质

BS ISO 11128. Specifications for blast cleaning abrasives. Recyclable encapsulated abrasive media

KS M ISO 8503-5:2021 涂料和相关产品使用前钢衬底的制备.喷砂清理钢衬底的表面粗糙度特性.第5部分:测定表面轮廓的复制胶带法

Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 5: Replica tape method for the determinat

KS M ISO 8503-5-2021 涂料和相关产品使用前钢衬底的制备.喷砂清理钢衬底的表面粗糙度特性.第5部分:测定表面轮廓的复制胶带法

Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 5: Replica tape method for the determinat

prEN ISO 11127-6:2021 涂装油漆和相关产品前钢基材的准备 非金属喷砂清理磨料的试验方法 第6部分：通过电导率测量测定水溶性污染物（ISO/DIS 11127-6:2021）

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 6: Determination of water-soluble contaminants by conductivity measurement (ISO/DIS 11127-6:2021)

PN-EN ISO 11124-5-2021-09 E 涂漆和相关产品前钢基材的准备 金属喷砂清理磨料规范 第5部分：切割钢丝（ISO 11124-5:2019）

Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 5: Cut steel wire (ISO 11124-5:2019)

T/CRRA 0807-2021 工程机械零部件再制造　清洗技术规范

本文件规定了以下主要技术内容： 4 清洗分类    根据清洗不同阶段和作用、清洗对象、被清除对象、清洗方式的不同对清洗作出了分类。 5 清洗的一般要求    对清洗工艺在清洁度、防腐、安全和环保方面提出了要求。  6 再制造清洗技术要求    对拆解前清洗、零部件再制造过程清洗、装配前清洗、涂装前清洗提出了要求。 7 清洗方法    对各阶段宜采用的清洗方法提出了要求。

Remanufacturing of construction machinery parts ——Technical specification for cleaning

BS ISO 11125-9:2021 涂装油漆和相关产品前，对钢衬底进行预处理 金属喷砂清理磨料的试验方法 磨损测试和性能

Preparation of steel substrates before application of paints and related products. Test methods for metallic blast-cleaning abrasives. Wear testing and performance

DS/ISO 11125-9:2021 涂装油漆和相关产品前钢基材的准备 金属喷砂清理磨料的试验方法 第9部分：磨损试验和性能

Preparation of steel substrates before application of paints and related products – Test methods for metallic blast-cleaning abrasives – Part 9: Wear testing and performance

ISO 11125-9:2021 涂料和相关产品使用前钢基体的制备.金属喷砂清理磨料的试验方法.第9部分:磨损试验和性能

This document specifies three procedures to test the service life of a blast-cleaning abrasive under laboratory conditions. The performance of an abrasive is also measured by its ability to clean, via transmission of kinetic energy to the substrate in the blasting process. This document also specifies the procedures that can be performed in the same testing machines to help evaluate abrasive performance under laboratory conditions. This document applies to the testing of virgin metallic blasting media in the delivery state by centrifugal blasting under laboratory conditions.

Preparation of steel substrates before application of paints and related products — Test methods for metallic blast-cleaning abrasives — Part 9: Wear testing and performance

PN-EN ISO 3861-2021-07 E 喷砂和喷砂用橡胶软管和软管组件 规范（ISO 3861:2021）

Rubber hoses and hose assemblies for sand and grit blasting -- Specification (ISO 3861:2021)

PN-EN ISO 11127-3-2021-07 E 涂料及相关产品涂装前钢材表面处理非金属喷砂清理磨料试验方法第3部分：表观密度的测定（ISO 11127-3:2020）

Preparation of steel substrates before application of paints and related products--Test methods for non-metallic blast-cleaning abrasives--Part 3: Determination of apparent density (ISO 11127-3:2020)

PN-EN ISO 11127-5-2021-07 E 涂料及相关产品涂装前钢材表面处理非金属喷砂清理磨料试验方法第5部分：水分的测定（ISO 11127-5:2020）

Preparation of steel substrates before application of paints and related products--Test methods for non-metallic blast-cleaning abrasives--Part 5: Determination of moisture (ISO 11127-5:2020)

PN-EN ISO 11127-2-2021-07 E 涂料及相关产品涂装前钢材表面处理非金属喷砂清理磨料试验方法第2部分：粒度分布的测定（ISO 11127-2:2020）

Preparation of steel substrates before application of paints and related products--Test methods for non-metallic blast-cleaning abrasives--Part 2: Determination of particle size distribution (ISO 11127-2:2020)

PN-EN ISO 11127-1-2021-07 E 涂料及相关产品涂装前钢材表面处理非金属喷砂清理磨料试验方法第1部分：取样（ISO 11127-1:2020）

Preparation of steel substrates before application of paints and related products--Test methods for non-metallic blast-cleaning abrasives--Part 1: Sampling (ISO 11127-1:2020)

UNI EN ISO 11127-1:2021 涂漆和相关产品前钢基材的准备 非金属喷砂清理磨料的试验方法 第1部分：取样

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 1: Sampling