25.220.40 标准查询与下载

KS D ISO 3497-2022 金属涂层 涂层厚度的测量 X射线光谱测定法

Metallic coatings－Measurement of coating thickness－X-ray spectrometric methods

KS D ISO 2178-2022 涂层厚度测量 磁性基材上的非磁性涂层 磁性法

Measurement of coating thickness－Non－magnetic coatings on magnetic substrates－Magnetic method

KS W 1139-2022 飞机镀镉（电镀）

Plating cadmium(electrodeposited) for aircraft

KS D ISO 12686-2022 金属和其他无机涂层 在镀镍、自催化镍或铬之前对金属制品进行自动控制喷丸处理 或作为最终表面处理

Metallic and other inorganic coatings－Automated controlled shot-peening of metallic articles prior to nickel, autocatalytic nickel or chromium plating, or as a final finish

KS D ISO 4518-2022 金属涂层 涂层厚度的测量 轮廓测定法

Metallic coatings－Measurement of coating thickness－Profilometric method

KS D ISO 2063-2022 金属及其他无机涂层 热喷涂 锌、铝及其合金

Metallic and other inoganic coatings－Thermal spraying－Zinc, aluminium and their alloys

KS D ISO 10587-2022 金属和其他无机涂层 ?测试金属涂层和未涂层外螺纹制品和棒材的残余脆化 ?斜楔法

Metallic and other inorganic coatings ? Test for residual embrittlement in both metallic-coated and uncoated externally-threaded articles and rods ? Inclined wedge method

ISO 1461:2022 钢铁制品上的热浸镀锌涂层.规范和试验方法

This document specifies the general properties of hot dip galvanized coatings and test methods for hot dip galvanized coatings applied by dipping fabricated iron and steel articles (including certain castings) in a zinc melt (containing not more than 2 % of other metals). This document does not apply to the following: a) sheet, wire and woven or welded mesh products that are continuously hot dip galvanized; b) tube and pipe that are hot dip galvanized in automatic plants; c) hot dip galvanized products (e.g. fasteners) for which specific standards exist and which can include additional requirements or requirements which are different from those of this document. NOTE Individual product standards can incorporate this document for the galvanized coating by quoting its number, or can incorporate it with modifications specific to the product. Different requirements can also be made for galvanized coatings on products intended to meet specific regulatory requirements. This document does not apply to after-treatment or additional coating of hot dip galvanized articles.

Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods

ISO 5154:2022 无线电波传输应用产品用装饰性金属涂层.名称与符号和特性方法

This document specifies the designation and the characterization methods of the decorative metallic coatings of the products for radio wave transmissive application. The designation consists of the transmission loss of the radio wave, the frequency band of the radio wave under consideration, the lightness and hue of the parts, as well as the main material and manufacturing process of metallic coatings. The characterization methods consist of the determination of the transmission loss of radio wave with specific frequency band and the evaluation of lightness and hue which represent the colour and appearance.

Decorative metallic coatings for radio wave transmissive application products — Designation and characterization method

ASTM D4584-05(2022) 测量电泳槽表观pH值的标准试验方法

1.1 This test method covers the measurement of the free hydrogen ion concentration of electrocoat baths and their ultrafiltrates. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Apparent pH of Electrocoat Baths

ASTM D6492-99(2022) 锌和锌/铝合金涂层钢上六价铬检测的标准实施规程

1.1 This practice can be used to detect the presence of hexavalent chromium on galvanized and zinc/aluminum alloy coated steel surfaces. Hexavalent chromium-bearing treatments (passivates) can be applied to coated steels to prevent storage stain. While passivated 55 % aluminum-zinc alloy coated steel is commonly painted, passivated galvanized steel is not. Chrome passivation may interfere with the successful pretreatment of galvanized steel, as well as contaminate cleaning and pretreatment baths on a coil coating line. 1.2 The amount of hexavalent chromium that will cause the indicator to produce a discernible pink color is in the range of 0.5 parts per million dissolved in the indicator solution. It is possible that a coated steel surface that produces a negative result does have chromium on the surface. If a material that yields a negative result is suspected of having chromium on the surface, instrumental methods should be used. Chrome deposits of 1 mg/ft2 can be easily missed by analytical instruments such as the scanning electron microscope with energy dispersive x-ray analysis (EDXA) capability. Auger electron spectroscopy (AES) or electron spectroscopy for chemical analysis (ESCA) can identify chemical species present in the levels required for adequate detection. Stripping the metallic coating and analyzing for chrome by atomic absorption or inductively coupled plasma can also give reliable results in detecting the presence of chrome. 1.3 This practice is designed to be a qualitative means of screening chrome passivated coils from those which are not chrome passivated. 1.4 Some chromium-free passivates are being used commercially. Although these products will test negative for hexavalent chromium, they may interfere with cleaning and pretreating. Chromium bearing passivates that contain film forming constituents such as acrylic resins are also being commercially applied. The reaction of these products to the spot test will vary. Abrading the surface with emery paper will improve the likelihood of reliable detection. This technique is not recommended for acrylic resin containing passivation treatments. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Detection of Hexavalent Chromium On Zinc and Zinc/Aluminum Alloy Coated Steel

T/CIPR 037-2022 真空电镀亮面轻质圈技术规范

本文件规定了真空电镀亮面轻质圈的术语和定义、技术要求、技术指标、一般要求，并描述了技术目标和技术效益。

Technical Specification for Vacuum Electroplating

ASTM B994/B994M-22 镍钴合金镀层的标准规范

1.1 This specification describes the requirements for corrosion-resistant coatings of electrodeposited nickel-cobalt on metallic substrates and electrodeposited nickel-cobalt used for electroforming. NOTE 1—The nickel-cobalt alloy is principally deposited as a coating on steel products. It can also be electrodeposited on iron, stainless steel, aluminum, titanium, and any other metal substrate. NOTE 2—The nickel-cobalt alloy coating has a low coefficient of friction of 0.08 that provides a dry lubricant on part surfaces that are in contact with each other and are subject to galling. 1.2 This specification incorporates an accelerated exposure test method to evaluate the effects of corrosion and galling on the coating, and incorporates a means of reporting the results to the purchaser. 1.3 The specification incorporates a classification scheme that establishes service conditions for thickness, classes of deposits based on the level of monitoring, and type based on supplemental coatings used after deposition. 1.4 The coating thickness ranges from 5 to >30 µm, and it can be applied to machined parts, springs, latches, threaded parts, fasteners, etc. The deposit can also be used to electroform parts requiring high strength with the alloy being maintained at 50 % nickel-cobalt. 1.5 The nickel-cobalt alloy is used to protect ferrous metals in contact with corrosive environments such as: oil and gas production facilities, coastal marine, and ACQ (Alkaline Copper Quaternary) treatments for wood treatments. 1.6 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This standard has been revised to comply with the Restriction of Hazardous Substances RoHS Requirements that seek to limit the exposure of workers and the public to toxic metals. The nickel-cobalt alloy does not contain any of the six Restricted Hazardous Substances. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Cobalt Alloy Coating

ASTM B999-15(2022) 导电和非导电基体上钛和钛合金电镀、钛和钛合金电沉积层的标准规范

1.1 This specification covers the requirements for electrodeposited coatings of titanium and titanium-zirconium alloys on conductive and non-conductive substrates for engineering (functional) uses. The coatings of titanium-zirconium alloys are those that range in zirconium between 10wt% and 14wt% zirconium and are known as “terne” metallic electrodeposits. 1.2 This specification applies for both conductive (metallic) substrates and non-conductive (plastics, fibers, carbon foam, etc.) 1.3 Electrodeposits of titanium and titanium-zirconium alloys on aluminum and conductive substrate and nonconductive substrate are produced where it is desired to obtain atmospheric corrosion resistance. Deposits of titanium and titaniumzirconium alloys particularly on aluminum have shown to have excellent corrosion protective qualities in atmospheric exposure, especially when under-coated by electroless nickel. Titanium and titanium-zirconium alloy deposits provide corrosion protection from dilute sulfuric acid, are used for lining of brine refrigeration tanks, chemical equipment apparatus, storage batteries, and as a wear coating for bearing surfaces. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Titanium and Titanium Alloys Plating, Electrodeposited Coatings of Titanium and Titanium Alloys on Conductive and Non-Conductive Substrate

ASTM B733-22 金属表面自动催化（化学镀）镍磷涂层的标准规范

1.1 This specification covers requirements for autocatalytic (electroless) nickel-phosphorus coatings applied from aqueous solutions to metallic products for engineering (functional) uses. 1.2 The coatings are alloys of nickel and phosphorus produced by autocatalytic chemical reduction with hypophosphite. Because the deposited nickel alloy is a catalyst for the reaction, the process is self-sustaining. The chemical and physical properties of the deposit vary primarily with its phosphorus content and subsequent heat treatment. The chemical makeup of the plating solution and the use of the solution can affect the porosity and corrosion resistance of the deposit. For more details, see ASTM STP 265 (1)2 and Refs (2), (3), (4), and (5). 1.3 The coatings are generally deposited from acidic solutions operating at elevated temperatures. 1.4 The process produces coatings of uniform thickness on irregularly shaped parts, provided the plating solution circulates freely over their surfaces. 1.5 The coatings have multifunctional properties, such as hardness, heat hardenability, abrasion, wear and corrosion resistance, magnetics, electrical conductivity provide diffusion barrier, and solderability. They are also used for the salvage of worn or mismachined parts. 1.6 The low phosphorus (2 to 4 % P) coatings are microcrystalline and possess high as-plated hardness (620 to 750 HK 100). These coatings are used in applications requiring abrasion and wear resistance. 1.7 Lower phosphorus deposits in the range between 1 % and 3 % phosphorus are also microcrystalline. These coatings are used in electronic applications providing solderability, bondability, increased electrical conductivity, and resistance to strong alkali solutions. 1.8 The medium phosphorous coatings (5 to 9 % P) are most widely used to meet the general purpose requirements of wear and corrosion resistance. 1.9 The high phosphorous (more than 10 % P) coatings have superior salt-spray and acid resistance in a wide range of applications. They are used on beryllium and titanium parts for low stress properties. Coatings with phosphorus contents greater than 11.2 % P are not considered to be ferromagnetic. 1.10 Units—The values stated in SI units are to be regarded as standard. 1.11 The following precautionary statement pertains only to the test method portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.12 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal

ASTM B579-22 锡铅合金电沉积涂层（焊锡板）的标准规范

1.1 This specification covers the requirements for electrodeposited tin-lead coatings on fabricated articles of iron, steel, copper, and copper alloys, to protect them against corrosion (Note 1), to improve and preserve solderability over long periods of storage, and to improve anti-galling characteristics. NOTE 1—Some corrosion of tin-lead coatings may be expected in outdoor exposure. In normal indoor exposure, tin-lead is protective on iron, copper, and copper alloys. Corrosion may be expected at discontinuities (pits or pores) in the coating. Porosity decreases as the thickness is increased. A primary use of the tin-lead coating (solder) is with the printed circuit industry as a solderable coating and as an etch mask material. 1.2 This specification applies to electrodeposited coatings containing a minimum of 50 % and a maximum of 70 % tin. The specification applies to mat, bright, and flow-brightened tin-lead coatings. NOTE 2—Tin-lead plating baths are composed of tin and lead fluoborates and of addition agents to promote stability. The final appearance may be influenced by the addition of proprietary brighteners. Without brighteners, the coatings are mat; with brighteners, they are semibright or bright. Flow-brightened coatings are obtained by heating mat coatings to above the melting point of tin-lead for a few seconds and then quenching; palm oil, hydrogenated oils, or fats are used as a heat-transfer medium at a temperature of 260 6 10 °C (500 6 20 °F), but other methods of heating are also in use. The maximum thickness for flow-brightening is about 7.5 µm (0.3 mil); thicker coatings tend to reflow unevenly. The shape of the part is also a factor; flat surfaces tend to reflow more unevenly than wires or rounded shapes (Note 3). NOTE 3—Volatile impurities in tin-lead coatings will cause bubbling and foaming during flow-brightening resulting in voids and roughness. The impurities can arise from plating solution addition agents and from improper rinsing and processing. 1.3 This specification does not apply to sheet, strip, or wire in the unfabricated form or to threaded articles having basic major diameters up to and including 19 mm (0.75 in.). 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Electrodeposited Coatings of Tin-Lead Alloy (Solder Plate)

ASTM A924/A924M-22 热浸法金属涂层钢板一般要求的标准规范

Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process

JIS G 3303:2022 马口铁和黑钢板

Tinplate and blackplate

ISO 2080:2022 金属和其他无机涂层.表面处理 金属和其他无机涂层.词汇

This document defines the terms related to the general types of surface-finishing processes. Emphasis is placed on practical usage in surface-finishing technology in the metal-finishing field. This document does not include terms for porcelain and vitreous enamel, thermally sprayed coatings and galvanising for which specialized vocabularies and glossaries exist. For the most part, basic terms that have the same meaning in surface finishing as in other fields of technology, and that are defined in handbooks and dictionaries of chemistry and physics, are not included.

Metallic and other inorganic coatings — Surface treatment, metallic and other inorganic coatings — Vocabulary

BS ISO 24284:2022 金属涂层 除冰盐环境下装饰镀铬腐蚀试验方法

What is ISO 24284 - Corrosion test method for decorative chrome plating about? ISO 24284 discusses metallic coatings. Metallic coatings contain a metallic element or alloy. Metallic coatings can be applied by using a sprayer, electrochemically, chemically, or mechanically. ISO 24284 specifies the apparatus, reagents, and procedure to assess the corrosion resistance of chromium electroplated parts in the presence of de-icing salts (especially calcium chloride) in the laboratory. This method is primarily applicable to decorative parts plated with chromium, especially to exterior (automobile) parts electroplated with nickel-chromium or copper-nickel-chromium. ISO 24284 simulates special corrosion in the presence of hygroscopic and corrosive de-icing salt and conductive mud with a high salt concentration on chromium electroplated deposits during winter. Who is ISO 24284 - Corrosion test method for decorative chrome plating for? ISO 24284 on the corrosion test method for decorative chrome plating is useful for: Steel manufacturing industries

Metallic coatings. Corrosion test method for decorative chrome plating under a de-icing salt environment