共找到 1390 条与 相关的标准,共 93 页
本标准规定了采用金相法测定复合金属覆层厚度所用的仪器、设备、材料及试样制备、测量方法与步骤。 本标准适用于测定复合金属的覆层厚度。
Methods for measuring thickness of coated layer on composite metal--The metallographic method
本标准规定了在电镀锌层和电镀镉层上用于防腐蚀的铬酸盐转化膜的具体要求。 本标准不适用于仅仅提供特殊颜色或为改善油漆附着强度的表面精饰。
Chromate conversion coatings on electroplated zinc and cadmium coatings
本标准适用于金属覆盖层中的电沉积层、自催化镀层、喷涂层的维氏和努氏显微硬度测定,也适用于铝上阳极氧化膜的维氏和努氏显微硬度测定,测定时试验力均低于10N。 要得到满意的结果,覆盖层必须具有足够的厚度,且一般宜在横断面上进行测定。
Metallic and related coatings--Vickers and knoop microhardness tests
本标准规定了在含二氧化硫气氛和凝露条件下,材料或产品耐蚀性能的试验方法。 本标准适用于金属覆盖层和非有机覆盖层的腐蚀试验。 本标准不适用于涂料和清漆覆盖层的腐蚀试验。
Metallic and other non-organic coatings--Sulfur dioxide test with general condensation of moisture
本标准规定用酸处理后的抗染色力来评定阳极氧化膜的封闭质量。 本标准适用于检验那些有待于在大气曝晒与腐蚀环境下工作的阳极氧化膜,更适用于对耐污染氧化膜的检验。 本标准不适用于检验高铜、高硅(Cu>2%,Si>4%)铝合金上形成的氧化膜;重铬酸钾封闭后的氧化膜;涂油、打蜡、上漆处理过的氧化膜;深色氧化膜;厚度小于3μm的氧化膜。
Anodizing of aluminium and aluminium alloys--Estimationof loss of absorptive power of anodic oxide coatings after sealing--Dye spot test with prior acid treatment
本标准规定用击穿电位检验铝及铝合金阳极氧化膜的绝缘性。 本标准适用于检验阳极氧化膜的绝缘性能,主要检验下列两种阳极氧化膜: a.对绝缘性能有一定要求的阳极氧化膜。 b.以击穿电位为原则,而制定的阳极氧化工艺所生产的阳极氧化膜。在一般情况下,本标准仅用于对封闭和干燥后的阳极氧化膜进行检验,不适用于对涂漆或有其他覆盖层的氧化膜进行检验。
Anodizing of aluminium and aluminium alloys--Insulation check by measurement of breakdown potential
本标准适用于铝及铝合金制品阳极氧化膜厚度的测定。 本标准不适用于测量特殊膜(如深色氧化膜)、试样基底粗糙的膜。在一般工业条件下,可测量10μm以上的膜。当表面平滑时也可测量5~10μm的氧化膜。
Test methods for thickness of anodic oxidation coatings on aluminium and aluminium alloys--Split-beam microscope method
本标准规定用重量法对铝及铝合金制品阳极氧化膜的厚度进行测量。 本标准适用于除铜含量大于6%以外的绝大部分铝合金。
Test methods for thickness of anodic oxidation coatings on aluminium and aluminium alloys--Gravimetric method
本标准规定了有关铝及铝合金阳极氧化膜厚度的术语和最小厚度的测量原则。
Anodizing of aluminium and aluminium alloys--Definitions thickness of anodic oxidation coatings and conventions concerning the measurement of thickness
本标准主要适用于铝及铝合金的阳极氧化膜。 本标准不适用的范围有: 屏蔽型无孔氧化膜; 用于有机涂覆底层或金属镀覆底层的氧化膜; 工程上应用的硬质阳极氧化膜。 本标准等同于ISO7599-1983《铝及铝合金阳极氧化--阳极氧化膜的总规范》。
Anodizing of aluminium and aluminium alloys--General specifications for anodic oxidation coatings
本标准规定了评定电沉积铬层的电解腐蚀试验方法,本方法快速而准确。 本标准适用于评价钢或锌合金铸件上的铜-镍-铬和镍-铬电沉积层在户外的耐蚀性。对产品在户外使用的期限和结果,本标准未作规定和解释。对于其他材料和其他沉积层体系,若要用本试验方法,则应事先验证本方法同其室外使用的相应关系。
Electrodeposited chromium coatings--Electrolytic corrosion testing (EC test)
本标准规定了用腐蚀膏法评价金属和其它无机覆盖层质量的试剂、设备和步骤。 本方法主要适用于铜-镍-铬或镍-铬电镀部件。
Metallic and other non-organic coatings--Corrodokote corrosion test(CORR test)
金属和其它无机覆盖层 厚度测量方法评述
Metallic and other non-organic coatings--Review of methods of measurement of thickness
金属和氧化物覆盖层 横断面厚度显微镜测量方法
Metallic and oxide coatings--Measurement of coating thickness--Microscopical method
本标准规定了电沉积层和化学沉积层附着强度的定性检验方法。
Metallic coatings on metallic substrates--Electrodeposited and chemically deposited coatings--Review of methods available for testing adhesion
Standard Test Methods for Determination of Tin Coating Weights for Electrolytic Tin Plate
Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments
Standard Specification for Electrodeposited Copper for Engineering Uses
Standard Specification for Electrodeposited Engineering Chromium Coatings on Ferrous Substrates
Standard Practice for Qualitative Adhesion Testing of Metallic Coatings
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号