59.140.30 皮革和裘皮 标准查询与下载

T/HEBQIA 159-2023 服装用绵羊皮革

本文件规定了服装用绵羊皮革的基本要求、技术要求、试验方法、检验规则、标志、包装、贮存、运输。

sheep leather for clothing

GSO ISO 17076-1:2023 皮革 耐磨性的测定 第1部分：泰伯法

This document specifies a method of determining the abrasion resistance of leather using a Taber® apparatus.

Leather — Determination of abrasion resistance — Part 1: Taber method

GSO ISO 2589:2023 皮革 物理和机械试验 厚度的测定

ISO 2589:2016 specifies a method for determining the thickness of leather. The method is applicable to all types of leather of any tannage. The measurement is valid for both the whole leather and a test sample.

Leather — Physical and mechanical tests — Determination of thickness

GSO ISO 17072-1:2023 皮革 金属含量的化学测定 第1部分：可萃取金属

This document specifies a method for the determination of extractable metals in leather using extraction with an acid artificial-perspiration solution and subsequent determination with inductively coupled plasma optical emission spectrometry (ICP-OES), inductively coupled plasma mass spectrometry (ICP-MS), atomic absorption spectrometry (AAS) or spectrometry of atomic fluorescence (SFA). This method determines extractable metals in leather; it is not compound-specific or specific to the oxidation state of the metals. This method is especially suitable for determining the extractable chromium in chromium-tanned leathers.

Leather — Chemical determination of metal content — Part 1: Extractable metals

GSO ISO 3376:2023 皮革 物理和机械试验 拉伸强度和伸长率的测定

This document specifies a method for determining the tensile strength, elongation at a specified load and elongation at maximum force of leather. It is applicable to all types of leather.

Leather — Physical and mechanical tests — Determination of tensile strength and percentage elongation

ASTM D6014-00(2023) 皮革表面动态吸水性测定的标准试验方法

1.1 This test method covers determining the degree of wettability of a leather surface. This test method does not apply to wet blue. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Dynamic Water Absorption of Leather Surfaces

ASTM D5552-10(2023) 彩色皮革抗出血性的标准试验方法

1.1 This test method covers the determination of the resistance of colored leather to bleeding. This test method does not apply to wet blue. 1.2 This test method is intended for use on finished upper leather for shoes or similar end use, or the leather article such as shoe, handbag, etc. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Resistance of Colored Leather to Bleeding

ASTM D5053-03(2023) 皮革克罗克色牢度的标准试验方法

1.1 This test method covers the determination of the degree of color that may be transferred from leather to other surfaces by rubbing under wet (damp) or dry conditions, or both. This test method does not apply to wet blue. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Colorfastness of Crocking of Leather

BS EN ISO 2418:2023 皮革 化学、物理、机械和牢度测试 测试样本的放置和准备

1   Scope This document specifies the position of laboratory test specimens within a piece of leather and the method of labelling and marking the laboratory test specimens for future identification. In addition, this document specifies the design of press knives for cutting test pieces and the preparation of test pieces. It is applicable to all types of leather derived from mammals, irrespective of the tanning used. It is not applicable to leathers derived from birds, fish, reptiles or furs.

Leather. Chemical, physical, mechanical and fastness tests. Position and preparation of specimens for testing

BS EN ISO 19076:2023 皮革 皮革表面的测量 电子技术

1   Scope This document provides a method for the measurement of the surface of leather or leather parts by the use of electronic measuring machines. It applies to the measurement of leather (or leather parts) fulfilling the following requirements: — flexible leather, finished or unfinished dry leather; — flexible wet leather (see Annex E); — flexibility, such as to allow full distension on the measuring line or surface.

Leather. Measurement of leather surface. Electronic techniques

BS EN ISO 14268:2023 皮革 物理和机械测试 水蒸气透过率的测定

1   Scope This document describes a method for determining the water vapour permeability of leather and provides alternative methods of sample preparation and for the measurement procedure.

Leather. Physical and mechanical tests. Determination of water vapour permeability

EN ISO 2418:2023 皮革化工,物理,机械和色牢度试验取样位置

This document specifies the position of laboratory test specimens within a piece of leather and the method of labelling and marking the laboratory test specimens for future identification. In addition, this document specifies the design of press knives for cutting test pieces and the preparation of test pieces. It is applicable to all types of leather derived from mammals, irrespective of the tanning used. It is not applicable to leathers derived from birds, fish, reptiles or furs.

Leather - Chemical, physical, mechanical and fastness tests - Position and preparation of specimens for testing (ISO 2418:2023)

EN ISO 14268:2023 皮革.物理和机械试验.水蒸气渗透性的测定

This document describes a method for determining the water vapour permeability of leather and provides alternative methods of sample preparation and for the measurement procedure.

Leather - Physical and mechanical tests - Determination of water vapour permeability (ISO 14268:2023)

EN ISO 19076:2023 皮革-皮革表面测量采用电子技术

This document provides a method for the measurement of the surface of leather or leather parts by the use of electronic measuring machines. It applies to the measurement of leather (or leather parts) fulfilling the following requirements: — flexible leather, finished or unfinished dry leather; — flexible wet leather (see Annex E); — flexibility, such as to allow full distension on the measuring line or surface.

Leather - Measurement of leather surface - Electronic techniques (ISO 19076:2023)

ISO 2418:2023 皮革.化学、物理、机械和牢度试验.试验样品的位置和制备

Leather — Chemical, physical, mechanical and fastness tests — Position and preparation of specimens for testing

ISO 2418:2023|IULTCS/IUP 2 皮革 化学、物理、机械和牢度测试 测试样品的位置和准备

This document specifies the position of laboratory test specimens within a piece of leather and the method of labelling and marking the laboratory test specimens for future identification. In addition, this document specifies the design of press knives for cutting test pieces and the preparation of test pieces. It is applicable to all types of leather derived from mammals, irrespective of the tanning used. It is not applicable to leathers derived from birds, fish, reptiles or furs.

Leather — Chemical, physical, mechanical and fastness tests — Position and preparation of specimens for testing

ISO 2418:2023 | IULTCS/IUP 2 皮革 化学、物理、机械和牢度试验 测试样品的位置和准备

Leather — Chemical, physical, mechanical and fastness tests — Position and preparation of specimens for testing

ISO 14268:2023 皮革.物理和机械试验.水蒸气渗透性的测定

This document describes a method for determining the water vapour permeability of leather and provides alternative methods of sample preparation and for the measurement procedure.

Leather — Physical and mechanical tests — Determination of water vapour permeability

ISO 14268:2023|IULTCS/IUP 15 皮革《物理机械试验》《水蒸气透过率的测定》

Leather — Physical and mechanical tests — Determination of water vapour permeability

ISO 19076:2023|IULTCS/IUP 58 皮革 皮革表面测量 电子技术

Leather — Measurement of leather surface — Electronic techniques